ST UM2248 User Manual
Hide thumbs Also See for UM2248:
Table of Contents

Advertisement

Quick Links

All manuals and user guides at all-guides.com
UM2248
User manual
Evaluation board with STM32L4R9AI MCU
Introduction
The STM32L4R9I-EVAL board is designed as complete demonstration and development
®
®
platform for the STMicroelectronics Arm
Cortex
-M4 core-based STM32L4R9AI
microcontroller with four I²C buses, three SPI and six USART ports, CAN port, two SAI
ports, 12-bit ADC, 12-bit DAC, internal 640-Kbyte SRAM and 2-Mbyte Flash memory, two
Octo-SPI memory interfaces, touch-sensing capability, USB OTG FS port, LCD-TFT
®
controller, MIPI
DSI host controller, flexible memory controller (FMC), 8- to 14-bit camera
interface and JTAG debugging support.
The STM32L4R9I-EVAL, shown in
Figure
3,
Figure
4, and
Figure
5, is used as a reference
design for user application development before porting to the final product.
The full range of hardware features on the board helps the user to evaluate all the
peripherals (USB, USART, digital microphones, ADC and DAC, TFT LCD, MIPI DSI
display, LDR, SRAM, NOR Flash memory device, Octo-SPI Flash memory device,
microSD™ card, sigma-delta modulators, CAN transceiver, EEPROM) and develop
applications. Extension headers allow easy connection of a daughterboard or wrapping
board for a specific application.
An ST-LINK/V2-1 is integrated on the board, as the embedded in-circuit debugger and
programmer for the STM32 MCU and the USB virtual COM port bridge.
October 2017
DocID030791 Rev 2
1/87
www.st.com
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the UM2248 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for ST UM2248

  • Page 1 Extension headers allow easy connection of a daughterboard or wrapping board for a specific application. An ST-LINK/V2-1 is integrated on the board, as the embedded in-circuit debugger and programmer for the STM32 MCU and the USB virtual COM port bridge.
  • Page 2: Table Of Contents

    9.3.2 ST-LINK/V2-1 firmware upgrade ......18 ETM trace ..........18 Power Supply .
  • Page 3 All manuals and user guides at all-guides.com UM2248 Contents 9.10 USB OTG FS port ......... . 26 9.10.1...
  • Page 4 10.16 TFT LCD connector CN20 (RGB) ......61 10.17 ST-LINK/V2-1 USB Micro-B connector CN21 ..... 61...
  • Page 5 All manuals and user guides at all-guides.com UM2248 Contents 10.18 CAN D-type male connector CN22 ......62 Electrical schematics .
  • Page 6 All manuals and user guides at all-guides.com List of tables UM2248 List of tables Table 1. Setting of configuration elements for trace connector CN12 ..... . . 19 Table 2.
  • Page 7 ST-LINK/V2-1 ........
  • Page 8: Features

    PMOD connector • Board expansion connectors: – Motor-control connector – Extension connector for daughterboard • Flexible power-supply options: power jack, ST-LINK/V2-1 USB connector, USB OTG FS connector, daughterboard • On-board ST-LINK/V2-1 debugger/programmer with USB re-enumeration capability: 8/87 DocID030791 Rev 2...
  • Page 9: Product Marking

    ST is not responsible for any consequences resulting from such use. In no event will ST be liable for the customer using any of these engineering samples tools as reference design or in production.
  • Page 10: Demonstration Software

    MCU, is preloaded in the STM32 Flash memory for easy demonstration of the device peripherals in standalone mode. The latest versions of the demonstration source code and associated documentation are available from www.st.com. Ordering information To order the evaluation board based on the STM32L4R9AII6 MCU, use the order code STM32L4R9I-EVAL.
  • Page 11: Hardware Layout And Configuration

    All manuals and user guides at all-guides.com UM2248 Hardware layout and configuration Hardware layout and configuration The STM32L4R9I-EVAL board is designed around STM32L4R9AII6 target microcontroller in UFBGA 169-pin package. Figure 1 illustrates STM32L4R9AII6 connections with peripheral components. Figure 2 shows the location of main components on the evaluation board.
  • Page 12: Figure 2. Stm32L4R9I-Eval Board (Top Side)

    All manuals and user guides at all-guides.com Hardware layout and configuration UM2248 Figure 2. STM32L4R9I-EVAL board (top side) 12/87 DocID030791 Rev 2...
  • Page 13: Stm32L4R9I-Eval Board Views

    All manuals and user guides at all-guides.com UM2248 Hardware layout and configuration STM32L4R9I-EVAL board views Figure 3. STM32L4R9I-EVAL board (top view) with round DSI display MB1314 daughterboard Picture is not contractual DocID030791 Rev 2 13/87...
  • Page 14: Figure 4. Stm32L4R9I-Eval Board (Top View) With Tft Lcd Mb1315 Daughterboard

    All manuals and user guides at all-guides.com Hardware layout and configuration UM2248 Figure 4. STM32L4R9I-EVAL board (top view) with TFT LCD MB1315 daughterboard Picture is not contractual 14/87 DocID030791 Rev 2...
  • Page 15: Figure 5. Stm32L4R9I-Eval Board (Bottom View)

    All manuals and user guides at all-guides.com UM2248 Hardware layout and configuration Figure 5. STM32L4R9I-EVAL board (bottom view) Picture is not contractual DocID030791 Rev 2 15/87...
  • Page 16: Mechanical Dimensions

    All manuals and user guides at all-guides.com Hardware layout and configuration UM2248 Mechanical dimensions Figure 6. MB1313 STM32L4R9I-EVAL board 16/87 DocID030791 Rev 2...
  • Page 17: St-Link/V2-1

    Hardware layout and configuration Figure 7. MB1314 DSI display daughterboard ST-LINK/V2-1 ST-LINK/V2-1 facility for debug and flashing of STM32L4R9AII6, is integrated on the STM32L4R9I-EVAL board. Compared to ST-LINK/V2 stand-alone tool available from STMicroelectronics, ST-LINK/V2- 1 offers new features and drops some others.
  • Page 18: Drivers

    STM32L4R9AII6. Section 9.5 provides more detail on powering STM32L4R9I-EVAL. For full detail on both versions of the debug and flashing tool, the stand-alone ST-LINK/V2 and the embedded ST-LINK/V2-1, refer to www.st.com. 9.3.1 Drivers Before connecting STM32L4R9I-EVAL to a Windows (XP, 7, 8 10) PC via USB, a driver for ST-LINK/V2-1 must be installed.
  • Page 19: Power Supply

    Power jack CN18, marked PSU_DC5V on the board. A jumper must be placed in E5V location of JP11. The positive pole is on the center pin as illustrated in Figure • Micro-B USB receptacle CN21 of ST-LINK/V2-1, provides up to 500mA to the board. Offering enumeration feature described in Section 9.5.1.
  • Page 20: Supplying The Board Through St-Link/V2-1 Usb Port

    EVAL from the power source. In the next phase of the enumeration procedure, the host PC informs the ST-LINK/V2-1 facility of its capability to supply up to 300 mA of current. If the answer is positive, the ST-LINK/V2-1 sets the U22 ST890 switch to ON position to supply power to the remainder of the STM32L4R9I-EVAL board.
  • Page 21: Table 2. Power Supply Related Jumpers Settings

    All manuals and user guides at all-guides.com UM2248 Hardware layout and configuration Table 2. Power supply related jumpers settings Jumper / solder Setting Configuration bridge STM32L4R9I-EVAL is supplied through CN18 power jack (marked PSU_DC5V). CN5 and CN6 extension connectors do not pass the 5 V of STM32L4R9I-EVAL to daughterboard.
  • Page 22: Clock References

    CN21 using USB charger. 1. On all ST-LINK/V2-1 boards, the target application is now able to run even if the STLINK/V2-1 is either not connected to an USB host, or is powered through a USB charger (or through a not-enumerating USB host).
  • Page 23: Reset Sources

    All manuals and user guides at all-guides.com UM2248 Hardware layout and configuration Table 3. X1 crystal related solder bridge settings (continued) Solder Setting Configuration bridge Default setting. Open PC15 OSC32_OUT terminal is not routed to extension connector CN5. X1 is used as clock reference.
  • Page 24: Bootloader Limitations

    To locate the visual date code information on the STM32L4R9II6 package, refer to its datasheet (DS12023) available at www.st.com, section Package Information. Date code related portion of the package marking takes Y WW format, where Y is the last digit of the year and WW is the week.
  • Page 25: Audio

    WA3: Using bootloader, load a patch code in RAM to write in Flash memory through same Write Memory write protocol as bootloader (code provided by ST). The patch code is available for download from www.st.com...
  • Page 26: Headphones Outputs

    All manuals and user guides at all-guides.com Hardware layout and configuration UM2248 9.9.2 Headphones outputs The STM32L4R9I-EVAL board potentially drives two sets of stereo headphones. Identical or different stereo audio content are played back in each set of headphones. STM32L4R9AII6 sends up to two independent stereo audio channels, via its SAI1 TDM port, to the WM8994 codec device.
  • Page 27: Limitations In Using Usb Otg Fs Port

    All manuals and user guides at all-guides.com UM2248 Hardware layout and configuration terminal of CN3 Micro-AB USB connector to power the USB device. For this to happen, the STM32L4R9AII6 sets the U2 power switch STMPS2151STR to ON state. The LD6 green LED marked OTG_FS indicates that the peripheral is supplied from the board.
  • Page 28: Motor Control

    All manuals and user guides at all-guides.com Hardware layout and configuration UM2248 9.13 Motor control The CN1 connector is designed to receive a motor-control (MC) module. Table 7 shows the assignment of CN1 and STM32L4R9AII6 terminals. Table 7 also lists the modifications to be made on the board versus its by-default configuration.
  • Page 29 All manuals and user guides at all-guides.com UM2248 Hardware layout and configuration Table 7. Motor-control terminal and function assignment (continued) Motor-control STM32L4R9AII6 microcontroller connector CN1 Alternate Terminal Port Board modifications for Terminal Function name name enabling motor control function Close SB37.
  • Page 30: Board Modifications To Enable Motor Control

    All manuals and user guides at all-guides.com Hardware layout and configuration UM2248 Table 7. Motor-control terminal and function assignment (continued) Motor-control STM32L4R9AII6 microcontroller connector CN1 Alternate Terminal Port Board modifications for Terminal Function name name enabling motor control function Close SB17.
  • Page 31: Figure 9. Pcb Top-Side Rework For Motor Control

    All manuals and user guides at all-guides.com UM2248 Hardware layout and configuration Figure 9. PCB top-side rework for motor control DocID030791 Rev 2 31/87...
  • Page 32: Figure 10. Pcb Bottom-Side Rework For Motor Control

    All manuals and user guides at all-guides.com Hardware layout and configuration UM2248 Figure 10. PCB bottom-side rework for motor control 32/87 DocID030791 Rev 2...
  • Page 33: Can

    All manuals and user guides at all-guides.com UM2248 Hardware layout and configuration 9.14 The STM32L4R9I-EVAL board supports one CAN2.0A/B channel compliant with CAN specification. The CN22 DB9 male connector is available as CAN interface. A 3.3 V CAN transceiver is fitted between the CN22 connector and the CAN controller port of STM32L4R9AII6.
  • Page 34: Extension Connectors Cn5, Cn6, Cn13 And Cn14

    All manuals and user guides at all-guides.com Hardware layout and configuration UM2248 9.15 Extension connectors CN5, CN6, CN13 and CN14 The CN5, CN6, CN13 and CN14 headers complement to give access to all GPIOs of the STM32L4R9AII6 microcontroller. In addition to GPIOs, the following signals and power supply lines are also routed on CN5 or CN6 or CN13 or CN14: •...
  • Page 35: Limitations

    All manuals and user guides at all-guides.com UM2248 Hardware layout and configuration Table 9. Port assignment for control of physical input devices Jumper Setting Routing Potentiometer is routed to pin PB4 o fSTM32L4R9AII6. Default setting. Potentiometer is routed to pin PA0 of STM32L4R9AII6.
  • Page 36: Comparator

    All manuals and user guides at all-guides.com Hardware layout and configuration UM2248 The R108 resistor in series with PA0 is beneficial for reducing the output offset. Table 10 shows the configuration elements and their settings allowing to access the OpAmp1 function.
  • Page 37: Limitations

    All manuals and user guides at all-guides.com UM2248 Hardware layout and configuration Table 11. Configuration elements related with Comp2 (continued) Element Setting Configuration R204 out Comp2_OUT is routed to pin PB5 of STM32L4R9AII6. SB48 open R204 Default setting. SB48 R204 in Comp2_OUT is not routed to pin PB4 of STM32L4R9AII6.
  • Page 38: Limitations

    All manuals and user guides at all-guides.com Hardware layout and configuration UM2248 Table 12. SRAM chip select configuration Resistor Fitting Configuration Default setting. SRAM chip select is controlled with FMC_NE1 R134 SRAM is deselected. FMC_NE1 is freed for other application purposes.
  • Page 39: Operating Voltage

    All manuals and user guides at all-guides.com UM2248 Hardware layout and configuration a case, the disconnected addressing inputs of the NOR Flash memory device are pulled down by resistors. Section 9.4 provides information on the associated configuration elements. 9.21.2 Operating voltage NOR Flash memory operating voltage must be in the range from 1.65 V to 3.6 V.
  • Page 40: Limitations

    All manuals and user guides at all-guides.com Hardware layout and configuration UM2248 Table 14. Configuration elements related with Octo-SPI Flash device (continued) Element Setting Configuration Default setting. R67 in OctoSPI1_IO6 data line is available at Octo-SPI Flash memory SB54 open device.
  • Page 41: Table 15. Touch-Sensing-Related Configuration Elements

    All manuals and user guides at all-guides.com UM2248 Hardware layout and configuration touch sensing performance, by isolating copper tracks to avoid disturbances due to their antenna effect. Table 15. Touch-sensing-related configuration elements Element Setting Configuration PC6 port is routed to CN6 connector for daughterboard.
  • Page 42: Limitations

    All manuals and user guides at all-guides.com Hardware layout and configuration UM2248 Table 15. Touch-sensing-related configuration elements (continued) Element Setting Configuration PB7 port is routed to CN5 connector for daughterboard. This setting is not good for robustness of touch sensing.
  • Page 43: Idd Measurement

    All manuals and user guides at all-guides.com UM2248 Hardware layout and configuration Table 16. MFX signals (continued) Direction Pin number Pin name Function of Terminal MFX functions of MFX of MFX STM32L4R9AII6 device (for MFX) MFX_GPIO8 EXT_RESET Output EXT_I2C MFX_GPIO9...
  • Page 44: Limitations

    All manuals and user guides at all-guides.com Hardware layout and configuration UM2248 Table 18. DSI display module connector CN16 (continued) Pin No. Description Pin connection Pin No. Description Pin connection DSI_D0_P DSI_D0_N DSI_D1_P DSI_D1_N BLVDD (5 V) SPI_CS PG12 BLVDD (5 V)
  • Page 45: Limitations

    All manuals and user guides at all-guides.com UM2248 Hardware layout and configuration mount on STM32L4R9I-EVAL board with RGB mode. Table 19 shows the assignment of CN20 and STM32L4R9AII6 terminals. Table 19. TFT LCD module connector CN20 RGB mode FMC mode...
  • Page 46: Pmod Connector

    All manuals and user guides at all-guides.com Hardware layout and configuration UM2248 9.31 PMOD connector The standard PMOD connector P1 is available on STM32L4R9I-EVAL board to support flexibility in small form factor application. The PMOD connector is implemented the PMOD type 2A and 4A on STM32L4R9I-EVAL board.
  • Page 47: Mb1315 Tft Lcd Board

    All manuals and user guides at all-guides.com UM2248 Hardware layout and configuration Table 21. MB1314 board connector CN1 pin function description (continued) Pin number Description Pin number Description 3.3 V I2C_SDA SWIRE I2C_SCL DSI_TE DSI_BL_CTRL DSI_RST Warning: Permanent Image sticking may occur if AMOLED displays same image for an extended period of time.
  • Page 48 All manuals and user guides at all-guides.com Hardware layout and configuration UM2248 Table 22. MB1315 board connector CN1 pin function description (continued) Pin number Description Pin number Description LCD_DSIP HSYNC VSYNC PCLK RST# BL_CTRL BL+5 V BLGND BLGND +3.3 V...
  • Page 49: Connectors

    All manuals and user guides at all-guides.com UM2248 Connectors Connectors 10.1 Motor-control connector CN1 Figure 11. Motor-control connector CN1 (top view) Table 23. Motor-control connector CN1 Pin of Pin of Description number number Description STM32L4R9AII6 STM32L4R9AII6 of CN1 of CN1...
  • Page 50: External I 2 C Connector Cn2

    All manuals and user guides at all-guides.com Connectors UM2248 10.2 External I C connector CN2 Figure 12. EXT_I2C connector CN2 (front view) Table 24. EXT_I2C connector CN2 Pin number Description Pin number Description I2C1_SDA (PH5) I2C_SCL (PH4) EXT_RESET (MFX_GPIO8) 10.3 USB OTG FS Micro-AB connector CN3 Figure 13.
  • Page 51: Analog Input-Output Connector Cn4

    All manuals and user guides at all-guides.com UM2248 Connectors 10.4 Analog input-output connector CN4 Figure 14. Analog input-output connector CN4 (top view) Table 26. Analog input-output connector CN4 Pin number Description Pin number Description Analog input-output PA4 10.5 Extension connectors CN5, CN6, CN13 and CN14 All GPIO signals from STM32L4R9AII6 are connected to extension connectors CN5, CN6, CN13 and CN14.
  • Page 52: Table 28. Daughter Board Extension Connector Cn6

    All manuals and user guides at all-guides.com Connectors UM2248 Table 27. Daughter board extension connector CN5 (continued) How to disconnect alternative functions to Description Alternative functions number use on the extension connector PH10 OCTO-SPI2_IO5 Remove the U5. OCTO-SPI2_NCS Remove the U5.
  • Page 53 All manuals and user guides at all-guides.com UM2248 Connectors Table 28. Daughter board extension connector CN6 (continued) How to disconnect alternative functions to Description Alternative functions number use on the extension connector LPUART1_RX Remove the U9. VBUS_FS, MC Remove R203, open SB35.
  • Page 54: Table 29. Daughter Board Extension Connector Cn13

    All manuals and user guides at all-guides.com Connectors UM2248 Table 28. Daughter board extension connector CN6 (continued) How to disconnect alternative functions to Description Alternative functions number use on the extension connector OCTO-SPI1_NCS Remove the U6. Table 29. Daughter board extension connector CN13...
  • Page 55: Table 30. Daughter Board Extension Connector Cn14

    All manuals and user guides at all-guides.com UM2248 Connectors Table 29. Daughter board extension connector CN13 (continued) How to disconnect alternative functions to Description Alternative functions number use on the extension connector FMC_A22 Keep the CN12 open. FMC_A0 DFSDM, MC Remove R242, open SB36.
  • Page 56 All manuals and user guides at all-guides.com Connectors UM2248 Table 30. Daughter board extension connector CN14 (continued) How to disconnect alternative functions to Description Alternative functions number use on the extension connector PE14 FMC_D11 PE15 FMC_D12 Do not use the CN11, CN12, CN15, CN17 for...
  • Page 57: Rs232 Connector Cn7

    All manuals and user guides at all-guides.com UM2248 Connectors 10.6 RS232 connector CN7 Figure 15. RS232 D-sub male connector (front view) Table 31. RS232 D-sub male connector Pin number Description Description number RS232_RX (PG8) RS232_RTS (PB12) RS232_TX (PG7) RS232_CTS (PB13) 10.7...
  • Page 58: Mfx Programming Connector Cn9

    All manuals and user guides at all-guides.com Connectors UM2248 Table 32. microSD connector CN8 Description Description number number SDIO_D2 (PC10) Vss/GND SDIO_D3 (PC11) SDIO_D0 (PC8) SDIO_CMD (PD2) SDIO_D1 (PC9) SDIO_CLK (PC12) MicroSDcard_detect (MFX GPIO15) 10.8 MFX programming connector CN9 The connector CN9 is used only for embedded MFX (multi function expander) programming during board manufacture.
  • Page 59: Trace Debugging Connector Cn12

    All manuals and user guides at all-guides.com UM2248 Connectors 10.10 Trace debugging connector CN12 Figure 18. ETM trace debugging connector CN12 (Top view) Table 34. Trace debugging connector CN12 Description Description number number +3.3 V TMS/PA13 TCK/PA14 TDO/PB3 TDI/PA15 RESET#...
  • Page 60: Dsi Display Connector Cn16 (Mipi)

    All manuals and user guides at all-guides.com Connectors UM2248 10.12 DSI display connector CN16 (MIPI) A TFT color LCD with MIPI DSI interface board is mounted on CN16. Refer to Section 9.29 detail. 10.13 JTAG connector CN17 Figure 19. JTAG/SWD debugging connector CN17 (Top view) Table 36.
  • Page 61: Power Connector Cn18

    10.17 ST-LINK/V2-1 USB Micro-B connector CN21 The USB connector CN21 is used to connect on board ST-LINK/V2-1 facility to a PC for programming and debugging purposes. Figure 21. USB Micro-B connector CN21 (front view) Table 37. USB Micro-B connector CN21 (front view)
  • Page 62: Can D-Type Male Connector Cn22

    All manuals and user guides at all-guides.com Connectors UM2248 Table 37. USB Micro-B connector CN21 (front view) (continued) Pin number Description Pin number Description Shield 10.18 CAN D-type male connector CN22 Figure 22. CAN D-type 9-pin male connector CN22 (front view) Table 38.
  • Page 63: Electrical Schematics

    All manuals and user guides at all-guides.com UM2248 Electrical schematics Electrical schematics This section provides design schematics for the STM32L4R9I-EVAL key features to help users to implement these features in application designs. This section includes: • Overall schematics for the STM32L4R9I-EVAL, see Figure 23 •...
  • Page 64: Figure 23. Overall Schematics For The Stm32L4R9I-Eval

    All manuals and user guides at all-guides.com Figure 23. Overall schematics for the STM32L4R9I-EVAL U_MCU U_MotorControl U_DSI LCD MCU.SchDoc MotorControl.SchDoc DSI LCD.SchDoc MC_CurrentA MC_CurrentA USART1_CK USART1_CK MC_CurrentB MC_CurrentB USART1_TX USART1_TX MC_CurrentC MC_CurrentC SWIRE SWIRE MC_PFC_IndCurr MC_PFC_IndCurr U_IDD_measurement DSI_BL_CTRL DSI_BL_CTRL MC_BusVoltage MC_BusVoltage IDD_measurement.SchDoc MC_Temperature...
  • Page 65: Stm32L4R9I-Eval Mcu

    All manuals and user guides at all-guides.com Figure 24. STM32L4R9I-EVAL MCU SB36 MC_CurrentA SB38 R242 MC_PFC_IndCurr DFSDM_DATA4 R214 SB37 MFX_IRQ_OUT MC_CurrentB SB39 R244 OpAmp1_INP SAI1_SDA SB40 SB43 MC_Temperature MC_CurrentC R216 R217 OpAmp1_INM LCD_INT SB54 MC_PFC_Vac PA0-WKUP OCTOSPI1_IO6 R215 SB55 OpAmp1_VOUT MC_BusVoltage R221 OCTOSPI1_CLK...
  • Page 66: Figure 25. Power Supply

    All manuals and user guides at all-guides.com Figure 25. Power supply connected by shunt of IDD_measurement circuitry VDD_MCU +3V3 ZEN056V130A24LS VDD_ADJ TP11 CN18 JP10 VDD_IO 220uF VDD_IO DC-10B VDD_MCU Header 2X1 100nF BNX002-01 ESDA7P60-1U1M VDDIO2 VDDA VDDIO2 VDDA VDD_MCU VDDA VSSA/VREF- +3V3 VREF+...
  • Page 67: Figure 26. Sram And Nor Flash Memory Devices And Tft Lcd

    All manuals and user guides at all-guides.com Figure 26. SRAM and NOR Flash memory devices and TFT LCD D[0..15] D[0..15] A[0..23] A[0..23] CN20 PF14 DQ15A-1 PF15 DQ14 PE15 DQ13 PE10 I/O15 DQ12 PE11 I/O14 DQ11 PD10 PE12 I/O13 DQ10 PD11 PE13 I/O12 PD12...
  • Page 68: Figure 27. Audio Codec Device

    All manuals and user guides at all-guides.com Figure 27. Audio codec device +3V3 I2C address: 0x34 LDO1VDD AGND +3V3 AVDD1 AGND SPKVDD1 AGND +1V8 SPKVDD2 SPKGND1 AVDD2 SPKGND2 +1V8 CPVDD CPGND DCVDD DGND DBVDD HP2GND +1V8 LDO2VDD R159 I2C_SDA R166 R165 LDO1ENA SCLK...
  • Page 69: Figure 28. Dsi Display Connector

    All manuals and user guides at all-guides.com Figure 28. DSI display connector DSI LCD CN16 DSI_CK_P DSI_INT DSI_CK_N DSI_D2_P SB28 DSI_D2_N SB27 DSI_D0_P DSI_D0_N DSI_D3_P SB31 DSI_D3_N SB30 DSI_D1_P DSI_D1_N PG12 SPI_CS PG13 USART1_CK SB25 C134 SPI_CLK BEAD(FCM1608KF-601T03) C135 10uF USART1_TX 100nF SB24...
  • Page 70: Figure 29. Physical Control Peripherals, Microsd Card And Eeprom

    All manuals and user guides at all-guides.com Figure 29. Physical control peripherals, microSD card and EEPROM MICRO SD (TF) Card Buttons LEDs SDIO1_D1 SDIO1_D0 PC11 SDIO1_D3 PC10 SDIO1_D2 R190 PC12 +3V3 Green SDIO1_CLK R187 PB15 LED1 SDIO1_CMD Orange R186 PH13 C103 WKUP LED2...
  • Page 71: Figure 30. Analog Input And Output And Touch-Sensing Device

    All manuals and user guides at all-guides.com Figure 30. Analog input and output and touch-sensing device Comp2_INP Comp2_INP Header 2X1 Default setting: Open Comp2_OUT Comp2_OUT ADC_DAC [N/A] 3386P-103(10K) Close to MCU on PCB Default setting: 1<->2 from Potentiometer ADC&DAC connector COMP2_OUT STM32L Potentiometer...
  • Page 72: Figure 31. St-Link/V2-1

    All manuals and user guides at all-guides.com Figure 31. ST-LINK/V2-1 +3V3_ST_LINK +3V3_ST_LINK CN19 R161 R160 STM_JTMS_SWDIO VBUS_FS STM_JTCK_SWCLK BAT60JFILM BAT60JFILM LDK120M33R +3V3_ST_LINK C136 C139 C142 C140 C137 Vout 4.7uF 100nF 100nF 100nF 100nF SB33 [N/A] +3V3_ST_LINK BAT60JFILM BYPASS VUSB_ST_LINK R162...
  • Page 73: Figure 32. Idd Measurement

    All manuals and user guides at all-guides.com Figure 32. IDD measurement R123 BEAD(FCM1608KF-601T03) VDD1 VDD1 C126 C127 100nF GPIO0 JOY_SEL SPARE GPIO1 JOY_DOWN MFX_IRQ_OUT MFX_IRQ_OUT GPIO2 JOY_LEFT TSC_XP/GPO0 GPIO3 JOY_RIGHT NRST BAT60JFILM MFX_aGPIO1 NRST TSC_XN/GPO1 GPIO4 JOY_UP TSC_YP/GPO2 GPIO5 uSD_Detect TSC_YN/GPO3 GPIO6 USB_PSON...
  • Page 74: Figure 33. Jtag And Trace Debug Connectors

    All manuals and user guides at all-guides.com Figure 33. JTAG and trace debug connectors CN15 PA13 PA13 TMS/SWDIO PA14 PA15 TCK/SWCLK PA14 TDO/SWO PA15 R104 TRST Tag-10_C RESET# R139 Only footprint with Cable: TC2050-IDC-NL [N/A] Trace connector JTAG connector CN17 CN12 JTAG R144...
  • Page 75: Figure 34. Motor-Control Connector

    All manuals and user guides at all-guides.com Figure 34. Motor-control connector +3V3 Motor control connector MC_EmergencySTOP EMERGENCY STOP MC_PWM_1H PWM_1H PH13 MC_PWM_1L PWM_1L MC_PWM_2H PWM_2H PH14 MC_PWM_2L PWM_2L MC_BusVoltage MC_PWM_3H PWM_3H PH15 MC_PWM_3L PWM_3L BUS VOLTAGE 100nF 100K MC_CurrentA PHASE A CURRENT + PHASE A CURRENT - PHASE B CURRENT + PHASE B CURRENT -...
  • Page 76: Figure 35. Usb Otg Fs Port

    All manuals and user guides at all-guides.com Figure 35. USB OTG FS port +3V3 MFX_GPIO7 USB_OVRCR To MFX FAULT VBUS MFX_GPIO6 USB_PSON From MFX STMPS2151STR 4.7uF Shield Shield Shield Shield 475900001 Hirose: ZX62RD-AB-5P8 +3V3 VBUS_FS PA11 USBOTG_DM PA12 USBOTG_DP PA10 USBOTG_ID I/O1 I/O4...
  • Page 77: Figure 36. Usart, Can Transceiver And Pmod Connector

    All manuals and user guides at all-guides.com Figure 36. USART, CAN transceiver and PMOD connector USART +3V3 DB9-male C106 C105 100nF 100nF C107 100nF 100nF 100nF UART_RTS_3V3 T1IN T1OUT UART_TX_3V3 T2IN T2OUT T3IN T3OUT R1OUTB R2OUTB R1OUT R1IN UART_RX UART_RX_3V3 R2OUT R2IN R3OUT...
  • Page 78: Figure 37. Octo-Spi Flash Memory Device

    All manuals and user guides at all-guides.com Figure 37. Octo-SPI Flash memory device R212 [N/A] OCTOSPI1_CLK SCLK OCTOSPI1_NCS OCTOSPI1_DQS OCTOSPI1_IO0 SIO0 C5 for VPP from Mircon OCTOSPI1_IO1 SIO1 OCTOSPI1_IO2 SIO2 OCTOSPI1_IO3 SIO3 OCTOSPI1_IO4 SIO4 VCCQ R202 PG11 OCTOSPI1_IO5 SIO5 VCCQ [N/A] OCTOSPI1_IO6 SIO6...
  • Page 79: Figure 38. Extension Connectors

    All manuals and user guides at all-guides.com Figure 38. Extension connectors Place close Memory Left CN13 PH14 PH12 PH15 PG15 PG10 PH13 11 12 11 12 PG13 PG12 13 14 13 14 15 16 15 16 PI10 17 18 17 18 PI11 19 20 19 20...
  • Page 80: Appendix A I/O Assignment

    All manuals and user guides at all-guides.com I/O assignment UM2248 Appendix A I/O assignment Table 39. STM32L4R9I-EVAL I/O assignment Primary UFBGA RGB LCD with Motor-control Pin name Pinout assignment 169 DSI FMC mode connector DSI_CKN DSI_CKP DSI_D0N DSI_D0P DSI_D1N DSI_D1P...
  • Page 81 All manuals and user guides at all-guides.com UM2248 I/O assignment Table 39. STM32L4R9I-EVAL I/O assignment (continued) Primary UFBGA RGB LCD with Motor-control Pin name Pinout assignment 169 DSI FMC mode connector JTDO/TRACESWO NJTRST || COMP2_INP SAI1_SD_B || COMP2_OUT TSC_G2_IO3 || USART1_TX...
  • Page 82 All manuals and user guides at all-guides.com I/O assignment UM2248 Table 39. STM32L4R9I-EVAL I/O assignment (continued) Primary UFBGA RGB LCD with Motor-control Pin name Pinout assignment 169 DSI FMC mode connector FMC_NWE LCD_NWE FMC_NWAIT LCD_DE FMC_NE1 FMC_D13 LCD_R3 FMC_D14 LCD_R4...
  • Page 83 All manuals and user guides at all-guides.com UM2248 I/O assignment Table 39. STM32L4R9I-EVAL I/O assignment (continued) Primary UFBGA RGB LCD with Motor-control Pin name Pinout assignment 169 DSI FMC mode connector PF11 DSI_TE/LCD_DE PF12 FMC_A6 PF13 FMC_A7 LCD_B1 PF14 FMC_A8...
  • Page 84 All manuals and user guides at all-guides.com I/O assignment UM2248 Table 39. STM32L4R9I-EVAL I/O assignment (continued) Primary UFBGA RGB LCD with Motor-control Pin name Pinout assignment 169 DSI FMC mode connector SPI2_NSS SPI2_SCK SPI2_MISO SPI2_MOSI MC_EmergencyST Audio_INT OCTOSPIP2_NCS OCTOSPIP2_CLK OCTOSPIP2_IO2...
  • Page 85 All manuals and user guides at all-guides.com UM2248 I/O assignment Table 39. STM32L4R9I-EVAL I/O assignment (continued) Primary UFBGA RGB LCD with Motor-control Pin name Pinout assignment 169 DSI FMC mode connector DocID030791 Rev 2 85/87...
  • Page 86: Revision History

    All manuals and user guides at all-guides.com Revision history UM2248 Revision history Table 40. Document revision history Date Revision Changes 18-Aug-2017 Initial version Added: STM32L4R9I-EVAL board bottom view in Figure 5 Bootloader limitation in Chapter 9.8.1 Warning on AMOLED display in Chapter 9.32...
  • Page 87 ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement.

Table of Contents