Advertisement
34
model no. 055-9035-4 | contact us 1-800-689-9928
52/38° CROWN MOULDING
Angle Between
Mitre Setting
Walls
146
10.66
147
10.34
148
10.01
149
9.69
150
9.37
151
9.05
152
8.73
153
8.41
154
8.09
155
7.77
156
7.46
157
7.14
158
6.82
159
6.51
160
6.20
161
5.88
162
5.57
163
5.26
164
4.95
165
4.63
166
4.32
167
4.01
168
3.70
169
3.39
170
3.08
171
2.77
172
2.47
173
2.15
174
1.85
175
1.54
176
1.23
177
0.92
178
0.62
179
0.31
45/45° CROWN MOULDING
Bevel Setting
Mitre Setting
Bevel Setting
13.32
12.20
11.93
12.93
11.83
11.59
12.54
11.46
11.24
12.16
11.09
10.89
11.77
10.73
10.55
11.38
10.36
10.20
10.99
10.00
9.85
10.60
9.63
9.50
10.21
9.27
9.15
9.82
8.91
8.80
9.43
8.55
8.45
9.04
8.19
8.10
8.65
7.83
7.75
8.26
7.47
7.40
7.86
7.11
7.05
7.47
6.75
6.70
7.08
6.39
6.35
6.69
6.03
6.00
6.30
5.68
5.65
5.90
5.32
5.30
5.51
4.96
4.94
5.12
4.61
4.59
4.72
4.25
4.24
4.33
3.90
3.89
3.94
3.54
3.53
3.54
3.19
3.10
3.15
2.83
2.83
2.75
2.48
2.47
2.36
2.12
2.12
1.97
1.77
1.77
1.58
1.41
1.41
1.18
1.06
1.06
0.79
0.71
0.71
0.39
0.35
0.35
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various
types of commercial solvents and may be damaged by their use. Use clean clothes to remove dirt, dust, oil,
grease, etc.
SAWDUST
Periodically, sawdust will accumulate under the table and base. This could cause difficulty in the movement
of the table when setting up a mitre cut. Frequently blow out or vacuum up the sawdust.
LOWER BLADE GUARD
Do not use the saw without the lower blade guard.
The lower blade guard is attached to the saw for your protection. Should the lower guard become damaged,
do not use the saw until the damaged guard has been replaced. Check regularly to make sure the lower
guard is working properly. Clean the lower guard of any dust or buildup with a damp cloth.
BATTERIES
The battery pack is equipped with lithium-ion rechargeable batteries. The duration of use from each charge
will depend on the type of work performed.
Do not disassemble the battery pack or attempt to replace the batteries. Handling of the batteries, especially
when wearing rings and jewellery, could result in a serious burn.
To obtain the longest possible battery life, read and understand the instruction manual.
•
It is good practice to unplug the charger and remove the lithium-ion battery pack when not in use.
CAUTION!
If blowing sawdust, wear proper eye protection to keep debris from blowing into eyes.
CAUTION!
• Do not use solvents on the guard. They could make the plastic cloudy and brittle.
• When cleaning the lower guard, disconnect battery pack to avoid unexpected start-up.
WARNING!
• To avoid fire or toxic reaction, never use gasoline, naphtha acetone, lacquer thinner or similar
highly volatile solvents to clean the mitre saw.
35
Advertisement
