Brand and product names are trademarks or registered trademarks of their respective owners. Disclaimer Winmate Inc. reserve the right to make changes, without notice, to any product, including circuits and/or software described or contained in this manual in order to improve design and/or performance.
Page 5
Preface Advisory Conventions Four types of advisories are used throughout the user manual to provide helpful information or to alert you to the potential for hardware damage or personal injury. These are Notes, Important, Cautions, and Warnings. The following is an example of each type of advisory. NOTE: A note is used to emphasize helpful information IMPORTANT:...
Page 6
IP65 Flat Stainless PCAP Panel PC User Manual CAUTION/ATTENTION Always ground yourself to remove any static charge before touching the CPU card. Modern electronic devices are very sensitive to static electric charges. As a safety precaution, use a grounding wrist strap at all times. Place all electronic components in a static-dissipative surface or static- shielded bag when they are not in the chassis.
Page 7
Preface user manual. o The equipment has been dropped and damaged. o The equipment has obvious signs of breakage. • Do not leave this equipment in an uncontrolled environment where the storage temperature is below -20°C (-4°F) or above 60°C (140°F). It may damage the equipment. CAUTION/ATTENTION Use the recommended mounting apparatus to avoid risk of injury.
Page 8
IP65 Flat Stainless PCAP Panel PC User Manual Federal Communications Commission Radio Frequency Interface Statement This device complies with part 15 FCC rules. Operation is subject to the following two conditions: This device may not cause harmful interference. This device must accept any interference received including ...
About This User Manual About This User Manual This User Manual provides information about using the Winmate® IP65 Flat Stainless PCAP Panel PC with Intel ® Celeron ® Bay Trail-M N2930 1.83 GHz processor. This User Manual applies to the IP65 Flat Stainless PCAP Panel PC –...
Page 10
IP65 Flat Stainless PCAP Panel PC User Manual Introduction This chapter gives you product overview, describes features and hardware specification. You will find all accessories that come with the device in the packing list. Mechanical dimensions and drawings included in this chapter.
Chapter 1: Introduction Chapter 1: Introduction Winmate® IP65 Flat Stainless PCAP Series Panel PC is rugged, industrial-grade panel PC series built to withstand challenging environments, undergoing rigorous testing to ensure safety and top performance. All of the models in the series are sealed to IP65 standard. Stainless housing features anti-corrosion properties making it suitable for food, chemical and pharmaceutical industries.
IP65 Flat Stainless PCAP Panel PC User Manual 1.2 Package Content Carefully remove the box and unpack your Panel PC. Please check if all the items listed below are inside your package. If any of these items are missing or damaged contact us immediately. Standard factory shipment list Panel PC Quick Start Guide (Hardcopy)
Chapter 1: Introduction 1.3 Connector Placement IP65 Flat Stainless PCAP Panel PC has IP65 type connectors with protection cap. For cable specifications refer to the Ch.2,“Cable Specifications” of this user manual.
IP65 Flat Stainless PCAP Panel PC User Manual 1.4 Physical Buttons and LED Indicators Physical buttons and LED indicators located on the rear side of the Panel PC. Physical Buttons Icon Button Description Reset Press to reset the system Power On/ Press to power on or power off the device LED Indicators LED Type...
Chapter 1: Introduction 1.5 Schematics and Dimensions This section contains mechanical drawing of the panel PC. Notice that this is a simplified drawing and some components are not marked in detail. 1.5.1 Dimensions 10.4" Unit: mm 1.5.2 Dimensions 15" Unit: mm...
Page 18
IP65 Flat Stainless PCAP Panel PC User Manual Getting Started This chapter tells you important information on power supply, adapter and precautions tips. Pay attention to power considerations.
Chapter 2: Getting Started Chapter 2: Getting Started This chapter provides information on how to connect the panel PC to the source of power, connector pinouts and the guideline to turn on/off the Panel PC. 2.1 Powering On 2.1.1 AC Adapter Components AC Adapter supplied with the power cord.
IP65 Flat Stainless PCAP Panel PC User Manual ALTERNATING CURRENT / MISE À LE TERRE! This product must be grounded. Use only a grounded AC outlet. Install the additional PE ground wire if the local installation regulations require it. *If you do not use a grounded outlet while using the device, you may notice an electrical tingling sensation when the palms of your hands touch the device.
Chapter 2: Getting Started 2.1.4 Connecting the Power Cable Mounting Steps: Connect the AC adapter to the DC-in jack connector located on the back side of the Panel PC. Connect the power cord to AC adapter. Plug the power cord to the AC outlet and the device will turn on automatically. Note: Power cords vary in appearance by region and country.
IP65 Flat Stainless PCAP Panel PC User Manual 2.2 Connector Pin Assignments This Panel PC is equipped with four connectors which are IP65 level and fool-proofing design. Use only the cables that are included in the package. The pin assignments of the cables are as follows. 2.2.1 Power Cable The Flat Stainless PCAP Panel PC has IP65 connector.
Chapter 2: Getting Started 2.2.3 Ethernet Cable The Flat Stainless PCAP Panel PC has IP65 Ethernet connector. Use Ethernet cable to connect the Panel PC to the Internet. 2.2.4 USB 2.0 Cable Flat Stainless PCAP Panel PC has one Full IP65 USB2.0 connector. Use USB2.0 cable to connect external devices such as mouse or keyboard to the Panel PC.
IP65 Flat Stainless PCAP Panel PC User Manual 2.3 Turning On and Off The unit is configured to Power ON when is connected to the power source (refer to Ch.2, “Powering On” section of this user manual for more details on how to power on the HMI device). You can Turn OFF the Panel PC with the Windows power settings.
Page 25
Chapter 2: Getting Started Operating the Device This chapter provides detailed information on how to operate the device. If you have been using touch-screen Panel PCs before, the interface may look familiar. Sections include system settings parameters.
IP65 Flat Stainless PCAP Panel PC User Manual CHAPTER 3: OPERATING THE DEVICE In this chapter you will find instructions on how to operate the Panel PC with Hot Tab. 3.1 Operating System Flat Stainless PCAP Panel PC support several versions of Windows OS: Windows 10 IoT Enterprise, Windows Embedded 8.1 Industry Pro, Windows Embedded 8 Standard, Windows 7 Pro for Embedded Systems, and Windows Embedded Standard 7 –...
3.3 How to Enable Watchdog To enable Watchdog, you need to download Winmate Watchdog utility. Find more information on Watchdog in “Watchdog Guide” that you can download from Winmate Download Center or File Share. Refer to the Ch.7, “Technical Support”...
Page 28
IP65 Flat Stainless PCAP Panel PC User Manual AMI UEFI BIOS Setup BIOS Setup Utility is a program for configuration basic Input / Output system settings of the computer for optimum use. This chapter provides information on how to use BIOS setup, its functions and menu.
CHAPTER 4: AMI UEFI BIOS SETUP CHAPTER 4: AMI UEFI BIOS SETUP BIOS Setup Utility is a program for configuration basic Input / Output system settings of the computer for optimum use. This chapter provides information on how to use BIOS setup, its functions and menu. 4.1 When and How to Use BIOS Setup To enter the BIOS setup, you need to connect an external USB keyboard, press <Del>...
IP65 Flat Stainless PCAP Panel PC User Manual The following Keys can be used after entering the BIOS Setup. Function General Help Previous Values Optimized Defaults Save & Exit Exit Change Opt. Enter Select or execute command Cursor ↑ Moves to the previous item Cursor ↓...
CHAPTER 4: AMI UEFI BIOS SETUP BIOS Setting Description Setting Option Effect System Language Displays the system Adjustment of the Set the language in language. [English] is language other language. The set up by default. language in this device is English. System Date/Time This is current date Date and time...
Page 32
IP65 Flat Stainless PCAP Panel PC User Manual BIOS Setting Description Setting Option Effect ACPI Settings Configures ACPI Enter Opens submenu settings F81866 Super IO Configures IO Enter Opens submenu Configuration settings Hardware Monitor Configures Hardware Enter Opens submenu Monitor settings S5 RTC Wake Configures RTC Enter...
Page 33
CHAPTER 4: AMI UEFI BIOS SETUP 4.2.2.1 ACPI Settings Advanced Configuration and Power Interface (ACPI) settings allow to control how the power switch operates. The power supply can be adjusted for power requirements. You can use the screen to select options of ACPI configuration.
Page 34
IP65 Flat Stainless PCAP Panel PC User Manual 4.2.2.2 F81866 Super IO Configuration You can use the screen to select options for Super IO Configuration, and change the value of the option selected. A description of the selected item appears on the right side of the screen. For items marked with ►, please press <Enter>...
Page 35
CHAPTER 4: AMI UEFI BIOS SETUP GPI0 Port Configuration You can use the screen to change GPI0 Port setting. Use these items to set parameters related to PIN3- PIN14 Control. 4.2.2.3 Hardware Monitor You can check PC Health Status parameters such as system temperature, fan speed etc.
Page 36
IP65 Flat Stainless PCAP Panel PC User Manual 4.2.2.4 S5 RTC Wake Settings Wake system from S5 enables or disables system wake on alarm event. It allows you to wake up the system in a certain time. Wake System from S5 with fixed time setting Select Fixed Time to set the system to wake on the specified time.
Page 37
CHAPTER 4: AMI UEFI BIOS SETUP Wake system from S5 after dynamic time setting Select Dynamic Time to set the system to wake on the current time + increase minute (s).
Page 38
IP65 Flat Stainless PCAP Panel PC User Manual 4.2.2.5 CPU Configuration BIOS Setting Description Setting Option Effect Socket CPU This item contains Enter Open sub-menu Information socket specific CPU information. CPU Thermal Thermal control Enter Open sub-menu Configuration Limit CPUID Limits CPIID Disabled/Enabled Enable/Disable this...
Page 39
CHAPTER 4: AMI UEFI BIOS SETUP 4.2.2.6 PPM Configuration BIOS Setting Description Setting Option Effect CPU C State Report Shows CPU C State Enabled/ Enable or Disable Report Disabled CPU C state report to OS Max CPU C-State Allows to enter C1, C3, C6, C7, Enable or Disable power-saving...
Page 40
IP65 Flat Stainless PCAP Panel PC User Manual 4.2.2.7 Thermal Configuration This menu allows controlling thermal settings of the computer. Refer to the descriptions on the top right side of the screen for detailed information about each setting. BIOS Setting Description Setting Option Effect...
Page 41
CHAPTER 4: AMI UEFI BIOS SETUP 4.2.2.8 IDE Configuration BIOS Setting Description Setting Option Effect Serial- ATA (SATA) Responsible for Enabled/ Enable or disable supporting chipset Disabled this function drives with SATA interface. SATA Speed Allows forcing the Gen1 The maximum Support speed limit SATA II speed will be...
Page 42
IP65 Flat Stainless PCAP Panel PC User Manual SATA Mode This option specifies the [AHCI] Selecting this option allows operation mode of you to take full advantage of modern IDE / SATA- the extended host controller controller chipset SATA II [IDE] SATA controller will operate in a mechanism similar to a...
Page 43
CHAPTER 4: AMI UEFI BIOS SETUP 4.2.2.9 Miscellaneous Configuration OS Selection This item allows users to select the proper Operating System. BIOS Setting Description Setting Option Effect Windows 8.X Allows user to Enter Use Windows 8.X choose the proper Windows 7 Allows user to Enter Use Windows 7...
Page 44
IP65 Flat Stainless PCAP Panel PC User Manual 4.2.2.10 CSM Configuration BIOS Setting Description Setting Effect Option CSM Support The Compatibility Support Enabled/ Enable or disable Module (CSM) is a Disabled the Compatibility component of the UEFI Support Module firmware that provides legacy BIOS compatibility by emulating a BIOS environment, allowing...
Page 46
CHAPTER 4: AMI UEFI BIOS SETUP Video Specifies which Video option ROM UEFI Only UEFI option is booted ROMs are booted Legacy Only Legacy option ROMs are booted Other PCI Specifies which option ROM is UEFI Only UEFI option Devices booted for devices other than the ROMs are booted network, storage or video...
Page 48
IP65 Flat Stainless PCAP Panel PC User Manual XHCI Hand-off This is a workaround for OSs Disable Disables this function without XHCI hand- off support. Enable Enables this function EHCI Hand-off This is a workaround for OSs Disable Disables this function without ECHI hand- off Enable Enables this function...
Page 49
CHAPTER 4: AMI UEFI BIOS SETUP 4.2.2.12 Platform Trust Technology BIOS Setting Description Setting Option Effect fTPM Trusted Platform Enabled/Disabled Enables or disables Module parameters this function...
Page 50
IP65 Flat Stainless PCAP Panel PC User Manual 4.2.2.13 Security Configuration BIOS Setting Description Setting Option Effect Trusted Execution Enabled/Disabled Enables or disables Technology this function parameters TXE HMRFPO TXE HMRFPO Enabled/Disabled Enables or disables parameters this function TXE Firmware TXE Firmware Enabled/Disabled Enables or disables...
CHAPTER 4: AMI UEFI BIOS SETUP 4.2.3 Chipset Menu For items marked with ►, please press <Enter> for more options. BIOS Setting Description Setting Option Effect High Precious Allow to set up Enabled/ Enables/Disables Timer High Precious Disabled this function Timer settings Restore AC Power This function allows...
IP65 Flat Stainless PCAP Panel PC User Manual 4.2.4 Security Menu In the Security menu, users can set administrator password, user password, and HDD security configuration. BIOS Setting Description Setting Option Effect Administrator Displays whether Enter Enter password Password or not an administrator password has been set.
CHAPTER 4: AMI UEFI BIOS SETUP 4.2.5 Boot Configuration The Boot menu sets the sequence of the devices to be searched for the operating system. The bootable devices will be automatically detected during POST and shown here, allowing you to set the sequence that the BIOS uses to look for a boot device from which to load the operating system.
Page 54
IP65 Flat Stainless PCAP Panel PC User Manual Fast Boot Enables or disables Disabled Disables this Fast Boot to function shorten the OS Enabled Enables this boot process. function (Default: Disabled). Boot Mode Select Specifies which Legacy Only Legacy option mode will be used is booted for booting...
CHAPTER 4: AMI UEFI BIOS SETUP 4.2.6 Save & Exit The Exit menu displays a way how to exit BIOS Setup utility. After finishing your settings, you must save and exit for changes to be applied. BIOS Setting Description Setting Option Effect Save Changes and This saves the...
Page 56
IP65 Flat Stainless PCAP Panel PC User Manual Discard Changes Reset system setup Enter <YES> Saves the changes and Reset without saving any changes Enter <NO> Return to the BIOS Setup Main Menu Save Changes Save changes done Enter <YES> Saves the changes so far to any of the setup options.
CHAPTER 4: AMI UEFI BIOS SETUP 4.3 Using Recovery Wizard to Restore Computer The Panel PC has a dedicate recovery partition stored on the hard drive of the PC to enable quick one-key recovery process. This partition occupies about 11GB of the storage space, and comes built-in to the PC. Note: Before starting the recovery process, make sure to backup all user data.
Page 58
IP65 Flat Stainless PCAP Panel PC User Manual Wait the recovery process to complete. During the recovery process, a command prompt will show up to indicate the percent of recovery process complete. The system will restart automatically after recovery completed.
Page 59
CHAPTER 4: AMI UEFI BIOS SETUP Driver Installation This chapter describes how to install all necessary drivers.
IP65 Flat Stainless PCAP Panel PC User Manual Chapter 5: Driver Installation This chapter provides guideline to driver installations. 5.1 Installing Chipset Driver Step 1 Insert the CD that comes with the motherboard. Open the file document “Chipset Driver” and click “infinst_auto.exe”...
Page 61
Chapter 5: Driver Installation Step 4 Click Next to install the driver. Step 5 Software setup progress window will appear, click Next to continue. Step 6 Click “Yes, I want to restart this computer now” to finish the installation.
IP65 Flat Stainless PCAP Panel PC User Manual 5.2 Installing Graphics Driver Step 1 Insert the CD that comes with the motherboard. Open the file document “Graphics Driver” and click Setup to execute the setup. Step 2 Setup Welcome Window will appear, click Next to continue the process. Step 3 Carefully read the license terms and click Yes to agree.
Chapter 5: Driver Installation 5.3 Installing Intel Sideband Fabric Device (Intel MBI) Driver (Windows 8) Step 1 Insert the CD that comes with the motherboard. Open the file document “MBI” and click “Setup.exe” to install the driver. Step 2 Welcome to the setup program window will appear, click Next to start the installation. Step 3 Carefully read the License Agreement terms and click Yes to agree.
IP65 Flat Stainless PCAP Panel PC User Manual 5.4 Installing Intel Trusted Engine Interface (Intel TXE) Driver Step 1 Insert the CD that comes with the motherboard. Open the file document “TXE” and click “Setup TXE.exe” to install the driver. Step 2 Welcome to the setup program window will appear, click Next to start the installation.
Chapter 5: Driver Installation 5.5 Installing Intel Network Connections User must confirm the type of operating system is being used before installing Intel Network Connections. Follow the steps below to complete the installation. Step 1 Click “PROWin64.exe” Step 2 Click Yes to start the installation. Step 3 Welcome window will appear, click Next to install the driver.
IP65 Flat Stainless PCAP Panel PC User Manual 5.6 Installing Audio Driver The ALC886 series are high-performance 7.1+2 channel high definition audio codecs that provide ten DAC channels for simultaneous support of 7.1 sound playback, plus 2 channels of independent stereo sound output (multiple streaming) through the front panel stereo outputs.
Page 67
Chapter 5: Driver Installation Mounting Solutions This chapter provides step-by-step mounting guide for all available mounting options.
IP65 Flat Stainless PCAP Panel PC User Manual Chapter 6: Mounting This chapter provides mounting guide for all available mounting options. Pay attention to cautions and warning to avoid any damages. WARNING! / AVERTISSEMENT! Follow mounting instructions and use recommended mounting hardware to avoid the risk of injury.
Refer to sub-sections below for more details. 6.3.1 VESA Mount Flat Stainless PCAP Panel PC has VESA mount holes on the rear side. Follow instructions below to mount the unit with VESA Mount bracket (not supplied by Winmate). Size VESA Plate...
Notice that both hooks on bracket should lock the notches on the back cover of the device. 6.3.2 Yoke Mount Yoke Mount solution allows installing the Panel PC with the bracket (not supplied by Winmate). Mounting instruction: 1. Place the Panel PC on the bracket stand, aiming screw holes for each other.
Page 71
Chapter 6: Mounting Technical Support This chapter includes directory to Winmate technical support.
This chapter includes technical support documents and software developing kit (SDK). If any problem occurs fill in problem report form enclosed and immediately contact us. 7.1 Software Developer Support Winmate provides the following SDK and Utilities for the IP65 Flat Stainless PCAP Panel PC Item File Type Description Watchdog SDK...
Chapter 7: Technical Support 7.2 Problem Report Form IP65 Flat Stainless PCAP Panel PC Customer name: Company: Tel.: Fax: E-mail: Date: Product Serial Number: ____________________________________________________ Problem Description: Please describe the problem as clearly as possible. Detailed description of the occurred problem will allow us to find the best solution to solve the problem as soon as possible. _______________________________________________________________________________________ _______________________________________________________________________________________ _______________________________________________________________________________________...
Page 74
IP65 Flat Stainless PCAP Panel PC User Manual Product Specifications This section includes product specifications. Appendix...
IP65 Flat Stainless PCAP Panel PC User Manual Appendix B: Order Information IP65 Flat Stainless PCAP Panel PC available for ordering in the following configurations. Panel PC SODIMM DDR3L Max 8GB Windows 10 IoT Enterprise Windows Embedded 8.1 Industry Windows Embedded 8 Standard Windows Embedded 7 Standard Storage Mini PCIe SSD Touch AG Coating...
Need help?
Do you have a question about the R10IB3S-SPT2 and is the answer not in the manual?
Questions and answers