Red Dots" Led Indicator (9); Maintenance And Service; Accessories; Storage - Narex ASV 200-2B BASIC Original Operating Manual

English
use the torque set function for batch or gentle tightening when
setting up the drive mode� The machine has a maximum torque
available when setting the impact free drilling mode� Impact drill-
ing makes drilling more efficient, e�g� when drilling into brick or
other such hard construction materials�
Attention! Only change the tightening/drilling/impact drilling
modes while the machine is idle!
Always use only drill bits designed for impact drilling when drilling
in this manner�
Tightening
Symbol = suitable for tightening�
Impact free drilling
Symbol = suitable for driving, drilling into metal, wood
etc�
Impact Drilling
Symbol = suitable for impact drilling into brick�
Setting up torque
The function for setting up torque can be used only if the machine
or set collar (6b) is set to tightening mode�
Proceed as per the above to set up torque�
Mounting and releasing tools
Turning the chuck mounting case (8) opens and closes the jaws
between which you place the working tools (drill bit, bit holder
etc�)� The machines are automatically equipped with a spindle stop,
which makes changing the tool using only one hand in the desired
direction very simple�
Mounting a belt clip
Place the machine on a horizontal surface (e�g� a working table)�
Slide the bent end of the belt clip (12) into the base for the belt
clip (14)� Secure the belt clip (12) using a fastening screw (13) and
a corresponding screwdriver� You can mount the belt clip to the
machine from the right, as well as the left side� Be careful not to
mount the belt clip the wrong way round� The belt clip position
must correspond to the illustration�

"RED DOTS" LED Indicator (9)

Battery charge status (capacity) indication:
Is activated automatically once you press the switch button (3)�
The LED light is on the entire time the machine is working� It turns
off immediately once the switch button is released� The following
lights up depending on the battery charge status (capacity):
• The battery is fully charged, all three status LED indicator lights
turn on�
• The battery capacity has exceeded 60 %, two red LED indicator
lights turn on (the middle and the right)�
• The battery capacity has exceeded 30 %, only one red LED in-
dicator light turns on (the right)�
Reversible defect indication
• Low battery voltage indicator – this can occur when the bat-
tery voltage nears a dangerous level, useful for its repeated,
proper and safe recharge� The control system disconnects the
engine and all the three LED indicator lights start blinking red�
Release the switch button and press it again� If the problem
persists, take the battery out of the machine and insert it into
the charger to recharge it� Place another (replacement) battery
into the machine and continue working�
• Excess load indicator – this can occur as a result of too much
power, e�g� during high torque levels, when the machine is
jammed etc� The control system disconnects the engine and
all the three LED indicator lights start blinking red� To turn the
machine on again, release the switch button and then press it
again�
• Overheating indicator – this can occur during long-term ex-
cessive use� The control system disconnects the engine and all
the three LED indicator lights start blinking red� To turn on the
machine again, you have to let it cool down� Cool down time
depends on how overheated it is�
22
Irreversible defect indication
May occur as a result of a combination of factors� e�g� during a
short circuit, engine failure, battery failure etc� All three LED indi-
cator lights begin blinking red� If the machine cannot be turned
on as per the above, bring it including the battery to your nearest
authorised service centre�
Table overview of problems and signals:
Reversible damage
Problem
Voltage too low Excess load
LED indicator Blinks red Blinks red
Machine status Disconnected Disconnected
Releasing and pressing the button (3)
Turning the
machine on
Inserting a
again
charged battery

Maintenance and service

Instructions for device cleaning
Start the motor and blow impurities and dust out of the vent holes
of the device� Use protective goggles for this operation� Clean the
external plastic parts by a wet rag and mild detergent� Though
these parts are made of the materials resistant to solvents, NEVER
use any solvent�
Instructions for cleaning the charger
Attention! Risk of electric shock. Prior to start handling
the charger, disconnect the line plug from the socket!
Impurities and dust can be removed from external charg-
er surfaces by a rag or a non-metal brush� Use neither water nor
detergents�
Attention! With respect to protection from el. shock
and preservation of the class of protection, all mainte-
nance and service operations requesting jig saw case
removal must be performed by the authorized service
centre only!
The current list of authorized service centres can be found at our
website www.narex.cz, section "Service centres"�

Accessories

The accessories recommended for use with this device are availa-
ble commercially in the shops with hand el� tools�

Storage

Packed appliance may be stored in dry, unheated storage place
with temperature not lower than -5 °C�
Unpacked appliance should be stored only in dry storage place
with temperature not lower than +5 °C with exclusion of all sudden
temperature changes�

Environmental protection

Power tools, accessories and packaging should be sorted for envi-
ronmental-friendly recy�
Only for EU countries:
Do not dispose of power tools into household waste!
According to the European Directive 2002/96/EC on waste electri-
cal and electronic equipment and its incorporation into national
law, power tools that are no longer suitable for must be separately
collected and sent for recovery in an environmental-friendly man-
ner�
Irreversible
damage
Overheating
Blinks red Blinks red
Disconnected Disconnected
Short-term break Authorised
to cool down service centre