Hayward HRSN6 Series Installation, Operation And Maintenance Instructions
Hide thumbs
Also See for HRSN6 Series:
Table of Contents
Advertisement
Quick Links
INSTALLATION, OPERATION AND
MAINTENANCE INSTRUCTIONS
HRSN6 Series
TO PREVENT POTENTIAL INJURY OR DAMAGE TO PROPERTY, READ THIS MANUAL CAREFULLY AND COMPLETELY.
Back to TOC
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Hayward Flow Control
HRSN6IOM Rev D ECR 102V
www.haywardflowcontrol.com
1-888-HAY-INDL (1-888-429-4635)
Page 1 of 24
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Hayward HRSN6 Series
Summary of Contents for Hayward HRSN6 Series
- Page 1 INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS HRSN6 Series TO PREVENT POTENTIAL INJURY OR DAMAGE TO PROPERTY, READ THIS MANUAL CAREFULLY AND COMPLETELY. Back to TOC USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Hayward Flow Control HRSN6IOM Rev D ECR 102V www.haywardflowcontrol.com 1-888-HAY-INDL (1-888-429-4635)
-
Page 2: Important Safety Instructions
– Potential pinch point. Equipment connected to or driven by this device may start unexpectedly and may cause personal injury or entrapment in linkage systems. Back to TOC USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Hayward Flow Control HRSN6IOM Rev D ECR 102V www.haywardflowcontrol.com... -
Page 3: Table Of Contents
Notice: HRSN6 Series actuators are fully assembled, calibrated and tested prior to leaving our factory. In most cases, after you have mounted the actuator to your device, you should be able to operate the actuator from fully CLOSED (CW) to fully OPEN (CCW) and back again, and find that no adjustments are needed. -
Page 4: Technical Information
None This IOM On/Off / Proportional 120VAC HRSLCSSPLMNTIOM reference correct IOM On/Off / Proportional 230VAC HRSLCSSPLMNTIOM Back to TOC USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Hayward Flow Control HRSN6IOM Rev D ECR 102V www.haywardflowcontrol.com 1-888-HAY-INDL (1-888-429-4635) Page 4 of 24... -
Page 5: Actuator Handling And Installation
• Notice: Do NOT parallel wire multiple on/off actuators together without utilizing isolation relays. If this is your intention, please contact HAYWARD FLOW CONTROL for a multiple actuator parallel wiring diagram. Back to TOC USE ONLY HAYWARD GENUINE REPLACEMENT PARTS... -
Page 6: Product Mounting And Setup
PRODUCT MOUNTING AND SETUP Notice: All HRSN6 Series actuators rotate CW to close the output shaft out the bottom of the actuator when viewed from above. On all HRSN6 models, the cam shaft rotates CCW when the output shaft rotates CW. -
Page 7: Torque Switches
Torque Switch cams shown with the lower cam tripping the lower switch (Actuator was driving CW before this trip) Back to TOC USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Hayward Flow Control HRSN6IOM Rev D ECR 102V www.haywardflowcontrol.com 1-888-HAY-INDL (1-888-429-4635) -
Page 8: Adjusting Cw End Of Travel
ONLY and is NOT to 3. CW position calibration is now complete. be used as an electrical travel limiting device. Back to TOC USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Hayward Flow Control HRSN6IOM Rev D ECR 102V www.haywardflowcontrol.com 1-888-HAY-INDL (1-888-429-4635) -
Page 9: Adjusting Ccw End Of Travel
ONLY and is NOT to 3. CCW position calibration is now complete. be used as an electrical travel limiting device. Back to TOC USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Hayward Flow Control HRSN6IOM Rev D ECR 102V www.haywardflowcontrol.com 1-888-HAY-INDL (1-888-429-4635) -
Page 10: Adjusting Auxiliary Switches
CW Limit Switch Red lines show when the contact is energized. Shown in Valve CW Position Shown in Valve CW Position Back to TOC USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Hayward Flow Control HRSN6IOM Rev D ECR 102V Will drive 270°CCW www.haywardflowcontrol.com... -
Page 11: Commissioning
Serious Damage to the actuator will result if the motor is allowed to drive the gear train into the mechanical stop! Remove power from this device BEFORE making any travel adjustments. Back to TOC USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Hayward Flow Control HRSN6IOM Rev D ECR 102V www.haywardflowcontrol.com... -
Page 12: Proportional Control
Serious Damage to the actuator will result if the motor is allowed to drive the gear train into the mechanical stop! Remove power from this device BEFORE making any travel adjustments. Back to TOC USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Hayward Flow Control HRSN6IOM Rev D ECR 102V www.haywardflowcontrol.com... - Page 13 8. If the actuator stops at the correct positions and generates a feedback signal representative of the position of the actuator, the actuator can be put into service and is fully operational. Back to TOC USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Hayward Flow Control HRSN6IOM Rev D ECR 102V www.haywardflowcontrol.com...
-
Page 14: Proportional Calibration
CW position. (reference only). Calibrate Calibrate Power LED Power LED Back to TOC USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Hayward Flow Control HRSN6IOM Rev D ECR 102V www.haywardflowcontrol.com 1-888-HAY-INDL (1-888-429-4635) Page 14 of 24... -
Page 15: Calibration - Continued
Block Feedback Select (Jumpers) 4-20mA 2-10vdc DEFAULT Calibrate Power Input Select (Jumpers) 4-20mA 2-10vdc Potentiometer Connector Back to TOC USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Hayward Flow Control HRSN6IOM Rev D ECR 102V www.haywardflowcontrol.com 1-888-HAY-INDL (1-888-429-4635) Page 15 of 24... -
Page 16: Troubleshooting
Adjusting CW/CCW End of Travel section. positioned correctly end of travel Back to TOC USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Hayward Flow Control HRSN6IOM Rev D ECR 102V www.haywardflowcontrol.com 1-888-HAY-INDL (1-888-429-4635) Page 16 of 24... -
Page 17: Troubleshooting
Adjusting CW/CCW End of Travel section. positioned correctly end of travel Back to TOC USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Hayward Flow Control HRSN6IOM Rev D ECR 102V www.haywardflowcontrol.com 1-888-HAY-INDL (1-888-429-4635) Page 17 of 24... -
Page 18: Mechanical Data
IN/MM # TURNS FOR 90° LBS/KG HRS6A 9.84 / 11.41 / 48 turns 90° 242 / Back to TOC USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Hayward Flow Control HRSN6IOM Rev D ECR 102V www.haywardflowcontrol.com 1-888-HAY-INDL (1-888-429-4635) Page 18 of 24... -
Page 19: Exploded View
Gearing ISO5211 Double Square Female Drive Socket ISO5211 Mounting Cast Iron Casting System NEMA 4X Protection Back to TOC USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Hayward Flow Control HRSN6IOM Rev D ECR 102V www.haywardflowcontrol.com 1-888-HAY-INDL (1-888-429-4635) Page 19 of 24... -
Page 20: Wire Sizing Chart
WIRE SIZING CHART Wire sizing data is provided in the table below to assist in the selection of the proper wire size for HRSN6 Series actuators using various wire sizes over distance. Be sure to reference the correct voltage and do not exceed the indicated length of the wire run for each model. -
Page 21: Wiring Diagrams
• On/Off Control • Torque Switches • Battery Backup HRSN6A 230vac On/Off • LCS Back USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Hayward Flow Control HRSN6IOM Rev D ECR 102V www.haywardflowcontrol.com 1-888-HAY-INDL (1-888-429-4635) Page 21 of 24... -
Page 22: Hrsn6A 120/230Vac Proportional
• Proportional Control • Torque Switches • Battery Backup HRSN6A 230vac Proportional • LCS Back USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Hayward Flow Control HRSN6IOM Rev D ECR 102V www.haywardflowcontrol.com 1-888-HAY-INDL (1-888-429-4635) Page 22 of 24... -
Page 23: Notes
NOTES Back USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Hayward Flow Control HRSN6IOM Rev D ECR 102V www.haywardflowcontrol.com 1-888-HAY-INDL (1-888-429-4635) Page 23 of 24... - Page 24 This page intentionally left blank "APAKGOFNANHKEJGPEK AAPFCECDDKEPEIBPPK ANPODIEIEJIPCIBPKK AEMNABBHNIDPKLELKK DLLLDLLDDLLLLLDLLL" Back to TOC USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Hayward Flow Control HRSN6IOM Rev D ECR 102V www.haywardflowcontrol.com 1-888-HAY-INDL (1-888-429-4635) Page 24 of 24...