1. Manuals
  2. Brands
  3. Yamaha Manuals
  4. Synthesizer
  5. CS6X
  6. Owner's manual

Qed Ef (Quick Edit Effect) - Yamaha CS6X Owner's Manual

Control synthesizer/tone generator
Hide thumbs Also See for CS6X:
Table of Contents

Advertisement

Point
When the Mode (see earlier) has been set to "split,"
this sets the split point. The actual note of the split
point will be assigned to the upper section.
You can also select the split point by pressing the note
while holding down the [SHIFT] key.
Settings: C-2 ~ G8
Master Keyboard settings (for split/layer)
Prameter Name
Zone1
TrnsCh
ch
TG
on
MIDI
on
Octave
+0
Transpose
+0
Note Limit Low
C-2
Note Limit High
p
Transmit Switch PB
on
Transmit Switch MW
on
Transmit Switch KnobA-C
on
Transmit Switch Knob1/2
on
Transmit Switch RB
on
Transmit Switch FC
on
Transmit Switch BC
on
Transmit Switch AT
on
Transmit Switch FS
on
Transmit Switch Sus
on
Transmit Switch Vol/FV
on
Transmit Switch Pan
on
Transmit Switch Bank Select
off
Transmit Switch Program Change
off
Transmit Preset Volume
100
Transmit Preset Pan
C
Transmit Preset Bank MSB
0
Transmit Preset Bank LSB
0
Transmit Preset PC
0
CS Control Number Assign
7
ch: Keyboard transmit channel
p:
split point
Details about each parameter are given on page 137.
For more information about Master Keyboard Mode,
refer to page 67.
Common Quick Edit
You can set various parameters governing the sonic
properties of the Layer Part, and many can be edited
using the Sound Control knobs on the front panel of
the CS6x. The following four screens are only
available when the Layer switch (Page 133) for each
Part is set to "on."
QED Level (Quick Edit Level)

QED EF (Quick Edit Effect)

QED Filter (Quick Edit Filter)
QED EG (Quick Edit Envelope Generator)
Split
Layer
Zone2
Zone3
Zone4
Zone1
Zone2
Zone3
Zone4
ch+1
ch
ch
ch
ch+1
ch
ch
on
off
off
on
on
off
off
on
off
off
on
on
off
off
+0
+0
+0
+0
+0
+0
+0
+0
+0
+0
+0
+0
+0
+0
p
C-2
C-2
C-2
C-2
C-2
C-2
G8
G8
G8
G8
G8
G8
G8
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
off
off
off
off
off
off
off
off
off
off
off
off
off
off
100
100
100
100
100
100
100
C
C
C
C
C
C
C
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
7
7
7
7
7
7
7
QED Level (Quick Edit Level)
You can set output level and pan parameters for each
Layer Part. The settings are also available in the Part
Edit screens.
Vol (Volume)
Set the output level of the Layer Part.
Settings: 0 ~ 127
Pan
Set the stereo pan position of the Layer Part. You
can also adjust this parameter using the [PAN] knob
on the front panel of the CS6x.
Settings: L63 (Left) ~ C (Center) ~ R63(Right)
RevSend (Reverb Send)
Set the Send level of the signal sent from Insertion
Effect 1/2 (or the bypassed signal) to the Reverb
effect. You can also adjust this parameter using the
[REVERB] knob on the front panel of the CS6x.
Settings: 0 ~ 127
ChoSend (Chorus Send)
Set the Send level of the signal sent from Insertion
Effect 1/2 (or the bypassed signal) to the Chorus
effect. You can also adjust this parameter using the
[CHORUS] knob on the front panel of the CS6x.
Settings: 0 ~ 127
QED EF (Quick Edit Effect)
You can set the amount of Chorus applied to the Layer
Part, as well as Portamento settings.
Chorus
Set the Return level of the Chorus effect as an offset
value.
Settings: -64 ~ 0 ~ +63
Portamento
Switch Portamento on or off. You can also set this
using the PORTAMENTO [ON/OFF] key on the
front panel of the CS6x.
Settings: off, on
124
Show Quick Links

Hide quick links:

Advertisement

Table of Contents
loading

Related Manuals for Yamaha CS6X

Related Content for Yamaha CS6X

This manual is also suitable for:

Cs6r

Table of Contents