Lyr Tune (Layer Tune); Lyr Out (Layer Out); Lyr Limit (Layer Limit) - Yamaha CS6X Owner's Manual

Mode
Select whether each Part is played back
monophonically (single notes only) or
polyphonically (multiple simultaneous notes).
This parameter is only available for Normal Voice Parts
1 to 16 and Plug-in 1/2 Parts.
Settings: mono, poly
Arp (Arpeggio switch)
Switch the Arpeggiator for the currently selected
Part on or off.
This parameter is not available for A/D Input and Multi
Plug-in Parts.
Settings: off, on
Layer (Layer switch)
When switched on, you can layer up to four Parts.
This parameter in not available for A/D Input and Plug-
in Parts.
Settings: off, on
You can also set the overall output level and stereo pan
position of the Layer when this is switched on (Page 119).
Layers may be slow to sound, depending on their
component Parts.
If you turn five or more Layer Switches "on," only four
Parts are enabled for the layer. These four Parts are
determined in the priority of Part01 to Part16, PartCL,
PartAD, PartP1, then PartP2. For disabled Parts, their
Layer switch values will be shown in brackets like "(on)."
RcvCh (MIDI Receive Channel)
Set the MIDI Receive Channel for each Part. Select
"off" for Parts that you do not want to respond to
MIDI.
Settings: 1 ~ 16, off

LYR Limit (Layer Limit)

You can set note ranges and velocity limits for each Part.
These parameters are not available for the A/D Input Part.
Note Limit
Set the lowest and highest notes of the keyboard
range for each Part. Each Part will only sound for
notes played within its specified range.
Settings: C-2 ~ G8 (for the lowest and highest notes)
If you specify the highest note first and the lowest note
second, for example "C5 to C4," then the note range
covered will be "C-2 to C4" and "C5 to G8."
You can set the lowest and highest notes in the range by
pressing notes on the keyboard while holding down the
[SHIFT] key.
Vel Limit
Set the minimum and maximum values of the
velocity range within which each Part will respond.
Each Part will only sound for notes played within its
specified velocity range.
Settings: 1 ~ 127 (for the minimum and maximum values)
If you specify the maximum value first and the minimum
value second, for example "93 to 34," then the velocity
range covered will be "1 to 34" and "93 to 127."

LYR Tune (Layer Tune)

You can set note shift and tuning parameters for each
Part.
These parameters are not available for the A/D Input Part.
NoteShift
Adjust the pitch of each Part in semitones.
Settings: -24 ~ +24
Detune
Offset (detune) the pitch of each Part by a very small
amount.
Settings: -12.8Hz ~ +12.7Hz

LYR Out (Layer Out)

You can select outputs for each Part.
Output
Assign each Part to an output.
Settings: L&R (Left and Right outputs), ind 1&2
(Individual Output 1&2) ind1 (Individual
Output 1), ind2, ind3, ind4, ind5, ind6, drum
For example, if you choose "L&R," the left channel will
be output through OUTPUT L and the right channel
will be output through OUTPUT R. Alternatively, if
you choose "ind1," the left and right signals will be
merged and output monaurally through INDIVIDUAL
OUTPUT 1.
Settings "ind3 to "ind6" are for future expansion
purposes and are currently not available.
You can select "drum" for Drum Voice and Phrase Clip
Parts. If you select "drum" for a Drum Voice Part, the
output settings for each Drum Key (Page 105) are used.
If you select "drum" for the Phrase Clip Part, the output
settings for each Clip key (Page 151) are used.
133