Yamaha CS6X Owner's Manual page 83

Control synthesizer/tone generator
Hide thumbs Also See for CS6X:
Table of Contents

Advertisement

Switch
Switch the Arpeggiator on or off. You can also set
this using the [ARPEGGIO ON/OFF] key on the
front panel of the CS6x.
Settings: off, on
Hold
Switch the Arpeggiator Hold on or off. You can also
set this using the [ARPEGGIO HOLD] key on the
front panel of the CS6x.
Settings: syncoff, off, on
Details about this are given on Page 44.
ARP Limit (Arpeggio Note Limit)
ARPíLimit)
C 1234
Note Limit
Set the lowest and highest notes in the Arpeggiator's
note range.
Settings: C-2 ~ G8 (lowest and highest set separately)
If you specify the highest note first and the lowest note
second, for example "C5 to C4," then the note range
covered will be "C-2 to C4" and "C5 to G8."
You can set the lowest and highest notes in the range by
pressing notes on the keyboard while holding down the
[SHIFT] key.
ARP Mode (Arpeggio Mode)
These parameters control the way in which notes are
played back by the Arpeggiator.
ARPíMode)
Key Mode
C 1234
Key Mode
Set how the Arpeggio is played back when keys on
the keyboard are pressed. There are 3 modes.
Settings:
sort:
Plays back notes in ascending order from the lowest key
pressed to the highest.
thru:
Plays back notes in the order in which the keys are pressed.
direct:
Plays back the notes exactly as you play them. If changes
to Voice parameters (such as Pan or Cutoff frequency) are
included in the Arpeggio sequence data, they will be
applied and reproduced whenever the Arpeggio plays back.
If the Arpeggio Category is set to Ct, you will not hear
any sounds unless you select "direct" here.
With the "sort" and "thru" settings, the order in which
notes are played back will depend on the Arpeggio
sequence data.
Note Limit
C-2
-
G 8
Vel Mode
sort
thru
Vel Mode (Velocity Mode)
Set the playback velocity of the Arpeggio. There are
2 modes.
Settings:
original:
Preset velocities are used in the Arpeggio sequence.
thru:
Velocities of the notes you play are used in the Arpeggio
sequence.
ARP PlayEF (Arpeggio Play Effects)
You can set Play Effects for the Arpeggio. Play Effects
can be used to temporarily adjust the timing and
velocity of MIDI notes, thus affecting the groove of the
Arpeggio pattern.
ARPíPlayEF)
C 1234
Unit
Adjust the Arpeggio playback time. For example, if
you set a value of 200%, the playback time will be
doubled and the tempo halved. Alternatively, if you
set a value of 50%, the playback time will be halved
and the tempo doubled. Normal playback time is
100%.
Settings: 50%, 66%, 75%, 100%, 133%, 150%, 200%
Vel (Velocity)
Set the Velocity offset value (the strength at which
the keyboard is played). This determines how the
original Velocities are increased or decreased during
Arpeggio playback. A setting of 100% means the
original values are used. Settings below 100% will
reduce the velocity of the Arpeggio notes, whereas
settings above 100% will increase the velocities.
Settings: 0% ~ 200%
If the Velocity value falls below 1, it will be limited to 1.
If it exceeds 127, it will be limited to 127.
Gate (Gate Time)
Set the Gate Time Rate value (the length of a note).
This determines how the original Gate Times are
increased or decreased during Arpeggio playback. A
setting of 100% means the original values are used.
Settings below 100% will shorten the gate times of
the Arpeggio notes, whereas settings above 100%
will lengthen them. You can also set this using the
[GATE TIME] knob on the front panel of the CS6x.
Settings: 0% ~ 200%
If the Gate Time value falls below 1, it will be limited to 1.
83
Unit
Vel
Gate
50%
200%
200%

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Cs6r

Table of Contents