Qed Ef (Quick Edit Effect) - Yamaha S-80 Owner's Manual

Point
When the Mode (see earlier) has been set to "split,"
this sets the split point. The actual note of the split
point will be assigned to the upper section.
You can also select the split point by pressing the note
while holding down the [SHIFT] key.
Settings: C-2 ~ G8
Master keyboard setting list (on split/layer)
Prameter Name Zone1
TrnsCh ch
TG on
MIDI on
Octave +0
Transpose +0
Note Limit Low C-2
Note Limit High p
Transmit Switch PB on
Transmit Switch MW on
Transmit Switch KnobA-C on
Transmit Switch Knob1/2 on
Transmit Switch RB on
Transmit Switch FC on
Transmit Switch BC on
Transmit Switch AT on
Transmit Switch FS on
Transmit Switch Sus on
Transmit Switch Vol/FV on
Transmit Switch Pan on
Transmit Switch Bank Select off
Transmit Switch Program Change off
Transmit Preset Volume 100
Transmit Preset Pan 40
Transmit Preset Bank MSB 0
Transmit Preset Bank LSB 0
Transmit Preset PC 0
CS Control Number Assign 7
ch: Keyboard transmit channel
p: split point
Details about each parameter are given on page 127
For more information about the master keyboard mode,
refer to page 57 in Basics Section.
Common Quick Edit
You can set various parameters governing the sonic
properties of the Layer Part, The following four
screens are only available when the Layer switch (Page
123) for each Part is set to on.
QED Level (Quick Edit Level)

QED EF (Quick Edit Effect)

QED Filter (Quick Edit Filter)
QED EG (Quick Edit Envelope Generator)
Split Layer
Zone2 Zone3 Zone4 Zone1 Zone2 Zone3 Zone4
ch+1 ch ch ch ch+1 ch ch
on off off on on off off
on off off on on off off
+0 +0 +0 +0 +0 +0 +0
+0 +0 +0 +0 +0 +0 +0
p C-2 C-2 C-2 C-2 C-2 C-2
G8 G8 G8 G8 G8 G8 G8
on on on on on on on
on on on on on on on
on on on on on on on
on on on on on on on
on on on on on on on
on on on on on on on
on on on on on on on
on on on on on on on
on on on on on on on
on on on on on on on
on on on on on on on
on on on on on on on
off off off off
off off off
off off off off off off off
100 100 100 100 100 100 100
40 40 40 40 40 40 40
0 0 0 0 0 0 0
0 0 0 0 0 0 0
0 0 0 0 0 0 0
7 7 7 7 7 7 7
QED Level (Quick Edit Level)
You can set output level and pan parameters for each
Layer Part. The settings are also available in the Part
Edit screens.
Vol (Volume)
Set the output level of the Layer Part.
Settings: 0 ~ 127
Pan
Set the stereo pan position of the Layer Part.
Settings: L63 (Left) ~ C (Center) ~ R63(Right)
RevSend (Reverb Send)
Set the Send level of the signal sent from Insertion
Effect 1/2 (or the by-passed signal) to the Reverb
effect.
Settings: 0 ~ 127
ChoSend (Chorus Send)
Set the Send level of the signal sent from Insertion
Effect 1/2 (or the by-passed signal) to the Chorus
effect.
Settings: 0 ~ 127
QED EF (Quick Edit Effect)
You can set the amount of Chorus applied to the Layer
Part, as well as Portamento settings.
Chorus
Set the Return level of the Chorus effect as an offset
value.
Settings: -64 ~ 0 ~ +63
Portamento
Switch Portamento on or off.
Settings: off, on
Time
Set the pitch transition time. Higher values mean
longer transition times.
Settings: -64 ~ 0 ~ +63
114