Performance Program Selection; Multi Edit - Yamaha CS6X Owner's Manual

Performance Program Selection

There are four ways in which you can select a
Performance.
Using the BANK/PROGRAM keys (CS6x)
Using the [DEC/NO] and [INC/YES] keys
Using the [DATA] knob
Using the Category Search
Using the [INC/YES] and [DEC/NO] keys, the [DATA]
knob or the Category Search function is the same as
selecting the Voice directly in Voice Play Mode. Refer
to Page 75, replacing the word "Voice" with
"Performance."
Using the BANK/PROGRAM Keys (CS6x)
1Press the MEMORY [INT] or [EXT] key and select
the Performance Memory. The selected Performance
Memory indicator in the display will blink.
MEMORY
PRE1
INT
PLG1
PFM Play) INT:128(H16)[Pf:Init Perf ]
EQ Low EQ Mid
Details about Performance Memories are given on Page 29.
2Press a BANK key ([A] to [H]) to select a Bank.
The Bank indicator in the display will blink.
Press Bank keys [A] to [D] when selecting an EXT
Performance.
MEMORY
PRE1 PRE2 A B C
DRUM 1 2 3
ELEMENT SELECT
INT EXT 1 2 3
DRUM GENERAL QED ARPEGGIO
PLG1 PLG2 9 10 11
OSC PITCH FILTER AMPLITUDE
PFM Play) INT:128(H16)[Pf:Init Perf ]
EQ Low EQ Mid
If you press the [EXIT] key here, the Performance selection
process is canceled and the original Performance is
reinstated.
If the Bank has already been selected, this step is not
required.
PRE2
DRUM
EXT
DRUM
PLG2
EQ Hi -1 +0
D E F G H
BANK
4 1 2 3 4
ELEMENT ON/OFF
4 5 6 7 8
CONTROL COM LFO EFFECT
PROGRAM
PART
12 13 14 15 16
LFO EQ PLG
EQ Hi -1 +0
Details about Banks are given on Page 29.
3Press a PROGRAM key ([1] to [16]) to select a
Program Number.
Performances can be selected by setting the Memory,
Bank and Program Number as explained in the three
steps given above. The display also shows the
selected Performance.
1 2 3 4
GENERAL QED ARPEGGIO CONTROL
9 10 11 12
OSC PITCH FILTER AMPLITUDE

Multi Edit

(Volume, Pan, Reverb/Chorus
Send, Note Shift)
You can set the output level (volume), stereo pan and
other parameters for each Part using the graphic editors
on screens 3 to 7. You can, for example, adjust each
Part's Volume and Pan parameters in real-time while
using the synthesizer as a multitimbral tone generator
with a sequencer.
Method of Setting Up
The same procedure applies to screens 3 to 7.
PFM Mlt) Volume
Part01
SHIFT PAGE A
PART/ELEMENT
1 2
1Use the [PAGE] knob to select the screen.
2Use Knob [A] to select the Part. You can choose
from PartCL (Phrase Clip Part), PartAD (A/D Input
Part), PartP1 (Plug-in 1 Part), PartP2 (Plug-in 2
Part), Part01 to Part16 (Voice Part 1 to 16). Apart
from the 7th screen (Note Shift), the Common
(Layer Common) parameters are the same for all
Layer Parts.
The parameter settings for each Part are shown as a
bar graph, giving you an idea of the overall sound
balance.
You can also use the MEMORY and PART keys on
the front panel to select each Part. The keys relate to
each Part as follows.
[PRE1/2] key ......................Common (Layer Common)
[INT] key ..............................PartCL (Phrase Clip Part)
[EXT] key ............................PartAD (A/D Input Part)
[PLG1] key ..........................PartP1 (Plug-in 1 Part)
[PLG2] key ..........................PartP2 (Plug-in 2 Part)
PART keys [1] to [16] (CS6x)..Part01 to Part16 (Voice Parts 1 to 16)
119
5 6 7 8
COM LFO EFFECT
PROGRAM
13 14 15 16
LFO EQ PLG
L
127 Ä ÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇ›
B C 1 2
3
PART
DATA