Poc Tables - Toshiba ESTIA RUA-CP1701H Service Manual

Monobloc Outdoor Unit
10.1.5.2. Air Setpoint Table
Access type: Read/Write
TABLE NAME: AIR_STP, PIC Table Type: 17H, instance 2
PAR. NAME
421 htoccstp
422 htunooff
423 htecooff
424 cloccstp
425 clunooff
426 clecooff
427 freezstp
428 deltastp
429 iat_fact
1. Occupancy modes
Occupancy Comfort Type
Home Comfort
Sleep Comfort
Away Eco
2. Sleep offset
The offset applied to the Home setpoint.
3. Away offset
The offset applied to the Home setpoint.

POC tables

10.1.6.
POC tables are used to control Follower units that are interconnected to operate in the same Header /
Follower assembly.
10.1.6.1. Follower 0 Status Table
Access type: Read-only
TABLE NAME: SLV0STAT, PIC Table Type: 615H, instance 1
PAR. NAME
1001 ewt
1002 lwt
1003 mod_stat
1004 alm
1005 cap_t
1006 cap_ovr
1007 pmp
1008 pmp_ovr
1009 flow_sw
1010 freq_cur
1011 wearfact
1. System Mode Status
-1 = Disabled
0 = Off
1 = Cool
2 = Heat
3 = unused
4 = DHW (Heat)
5 = Booster Cooling
6 = Booster Heating
7 = Defrost
8 = Purge
9 = Drying
RANGE DEFAULT
12.0 to 34.0 19.0
-10.0 to 0.0 -2.0
-10.0 to 0.0 -4.0
20.0 to 38.0 26.0
0.0 to 10.0 2.0
0.0 to 10.0 4.0
6.0 to 12.0 6.0
0.2 to 1.0 0.5
0.0 to 2.0 0.0
RANGE DEFAULT
xx.x -
xx.x -
0 to 101 -
Normal/Alarm -
0 to 100 -
0 to 204 -
0 to 100 -
-1 to 100 -
Close/Open -
0 to 120 -
xxxxxxxx -
UNIT DESCRIPTION
°C Heat Home Setpoint
^C Heat Sleep Offset
^C Heat Away Offset
°C Cool Home Setpoint
^C Cool Sleep Offset
^C Cool Away Offset
°C Home AntiFreeze Setpoint
^C Air Delta Setpoint
- IAT Reset Factor
4. Anti-freeze setpoint
This is the minimum room temperature that is allowed.
If room temperature drops below this setpoint, the unit will
start to operate in Heating mode.
5. Air delta setpoint
This parameter is used to determine whether the control
is in cooling or heating demand.
6. IAT reset factor
This parameter is used to determine the indoor air
temperature.
UNIT DESCRIPTION
°C Entering Water Temp
°C Leaving Water Temp
- System Mode Status
- Alarm Status
% Total Capacity
- Capacity Override
% Water Pump Speed
- Pump Override
- Flow Switch Status
Hz Actual Compressor Freq
- Unit Wear Factor
20 = Home Anti-Freeze
21 = Cool Satisfied
22 = Heat Satisfied
24 = DHW Satisfied
29 = Drying Satisfied
100 = Not Responding
101 = Failed
2. Unit wear factor
The unit wear factor is calculated based on the number of
operating hours of the compressor as well as the number
of starts of the compressor
121
Service Manual
1
1, 2
1, 3
1
1, 2
1, 3
4
5
6
1
2