Mub-Mina/Lina U-Bracket - Meyer Sound LINA Operating Instructions Manual

MUB-MINA/LINA U-BRACKET

The MUB-MINA/LINA U-bracket was primarily designed for
aiming a single LINA loudspeaker in floor- and ceiling-mount
configurations (Figure 35). However, the U-bracket is strong
enough to fly arrays of up to five cabinets, or stack up to two
cabinets in floor- and pole-mount configurations. With the
U-bracket, up to two LINA loudspeakers can also be flown
from trusses using C-clamps or the equivalent. For flying and
groundstacking larger arrays, the MG-MINA/LINA/750-LFC
grid is recommended; for applications requiring continuous
adjustability or greater downtilt and uptilt angles, the
MYA-MINA/LINA mounting yoke is recommended.
NOTE: For complete information about
configuration and load ratings for the
MUB-MINA/LINA, as well as for other rigging
accessories, refer to the MG-MINA/LINA/750-LFC
Assembly Guide (PN 05.207.101.02) available at
www.meyersound.com.
Figure 35: Ceiling-Mounted MUB-MINA/LINA with One LINA
The MUB-MINA/LINA U-bracket's mounting holes and
mounting slot provide maximum flexibility for the
loudspeaker's uptilt and downtilt. For flown applications, the
MUB-MINA/LINA can be oriented for either maximum downtilt
(with the slot near the front of the loudspeakers) or maximum
uptilt (with the slot near the rear of the loudspeakers).
For a single flown cabinet, the MUB-MINA/LINA supports
•
continuous angles of 0° to –20° in the maximum downtilt
orientation, and angles of +10° to –10° in the maximum
uptilt orientation.
For multiple flown cabinets, the MUB-MINA/LINA supports
•
fixed angles of +10°, 0°, –5°, –10° and –20° (with either ori-
entation).
NOTE: For multiple flown cabinets, the
MUB-MINA/LINA slot is not recommended for
variable adjustments, because the angle could change
over time due to the weight of the cabinets.
NOTE: For illustrations showing which
MUB-MINA/LINA mounting holes and slot
configurations to use to achieve specific angles, refer to
the MG-MINA/LINA/750-LFC Assembly Guide
(PN 05.207.101.02) available at
www.meyersound.com.
Floor- and Pole-Mounting LINAs with the
MUB-MINA/LINA
Up to two LINA loudspeakers can be floor- or pole-mounted
with the MUB-MINA/LINA U-bracket (Figure 36). When pole-
mounting LINAs with the U-bracket, the optional 35 mm pole
stand adapter is required (PN 40.010.971.01). For floor- and
pole-mounted applications, the MUB-MINA/LINA can be
oriented for either maximum downtilt (with the slot near the
rear of the loudspeakers) or maximum uptilt (with the slot near
the front of the loudspeakers).
For a single floor- or pole-mounted cabinet, the
•
MUB-MINA/LINA supports continuous angles from +10 to
–10° in the maximum downtilt orientation, and angles of 0
to +20° in the maximum uptilt orientation.
For multiple floor- or pole-mounted cabinets, the
•
MUB-MINA/LINA supports fixed angles of 0, +5, and +10°
(with either orientation).
Figure 36: Pole-Mounted MUB-MINA/LINA/750 with Two LINA
loudspeakers using the 35 mm pole stand adapter
CAUTION: When mounting the MUB-
!
MINA/LINA on a pole, make sure the pole and
pole stand adapter have been rated to support the full
LINA OPERATING INSTRUCTIONS
31