VGA/component, Audio & RS-232 over CAT5 Extender with IR Pass-through has been tested for conformance to safety regulations and requirements, and has been certified for international use. However, like all electronic equipments, the AV-GM03S3-S1 should be used with care. Please read and follow the safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit.
1920x1200@60) or 720p component video, bi-directional IR signals and RS-232 serial commands at the same time to cover the distance up to 300m (1,000ft). The AV-GM03S3-S1 comes in a set of a transmitter and a receiver. The transmitter AV-GM03S3-S1[Tx] is installed near the signal source and has, and the receiver AV-GM03S3-S1[Rx] is placed near the desired display.
SPECIFICATIONS Model Name AV-GM03S3-S1 Transmitter [TX] Receiver [RX] Role of usage 350MHz Video bandwidth VESA Video support WUXGA [1920x1200] / 720p — 300m (1,000ft) [CAT5e] Video Transmission Audio support Stereo Half-duplex RS-232 signal type 1.2 Volts [peak-to-peak] Input video signal...
PANEL DESCRIPTIONS Transmitting unit ► AV-GM03S3-S1-TX Front Panel 1. RS-232: connect to a RS-232 signal source or receiver 2. IR-Blaster: connect to IR blaster for IR pass-through from RX to TX 3. Stereo IN: connect to analog audio source 4. S/PDIF IN: connect to digital audio source 5.
Page 6
10. System OUT: Plug in a Cat-5/5e/6 cable that needs to be linked to the RJ-45 connector of the receiving unit AV-GM03S3-S1[Rx] 11. Local S/PDIF: Digital stereo audio loop-out 12. Local Stereo: Analog stereo audio loop-out Receiving unit ► AV-GM03S3-S1-RX Front Panel 13. RS-232: Connect to a RS-232 device 14. IR Receiver: Connect to the IR receiver 15.
ON [] OFF [] AV-GM03S3-S1[RX] of AV-GM03S3-S1[TX] is connected to RxD of AV-GM03S3-S1[RX] Master to Slave Mode – TxD of AV-GM03S3-S1[TX] is connected to RxD of OFF [] ON [] OFF [] ON [] AV-GM03S3-S1[RX] RxD of AV-GM03S3-S1[TX] is connected to TxD of AV-GM03S3-S1[RX] 1.
IR Blaster:Plug in an IR blaster here to emit all IR command signals received from the IR receiver on AV-GM03S3-S1[Rx] to control the associated devices with built-in IR sensor IR Receiver:Plug in an IR receiver here to receive all IR command signals from the IR remote controls...
You can buy any IR extension cables in the market that are compatible to the definition of the IR sockets for the matrix if necessary for replacement use. However, IR cables longer than 2m (6-ft) may not work. SUPPORTED IR DATA FORMAT Data Format Suitable Not Recommended...
4. Make sure this Cat-5/5e/6 cable is tightly connected and not loose. 5. Plug in 5V DC power supply unit to the power jack of the receiving unit AV-GM03S3-S1[Rx]. 6. Plug in 5V DC power supply unit to the power jack of the transmitting unit AV-GM03S3-S1[Tx].
PIN DEFINITION Pair of Cat-5/5e/6 Cable Associated Definition Green Audio Blue RED channel of VGA Orange GREEN channel of VGA Brown BLUE channel of VGA...
NOTICE 1. All transmission distances are measured using Belden 1583A CAT5e 125MHz Solid UTP cable and ASTRODESIGN Video Signal Generator VG-859C. The transmission distance is defined as the distance between the video source and the VGA display. 2. The transmission length is largely affected by the type of CAT5/6 cables, the type of VGA sources, and the type of VGA display.
Page 13
The SELLER will NOT be liable for direct, indirect, incidental, special, or consequential damages resulting from any defect or omission in this manual, even if advised of the possibility of such damages. Also, the technical information contained herein regarding the AV-GM03S3-S1 features and specifications is subject to change without further notice.
Need help?
Do you have a question about the AV-GM03S3-S1 and is the answer not in the manual?
Questions and answers