Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Impulse IT8009 Total Hip
Summary of Contents for Impulse IT8009 Total Hip
- Page 1 T8009 Total Hip Assembly Instructions...
-
Page 2: Table Of Contents
Table of contents Important Safety Instructions--------------------------------- 1 Exploded View Diagram------------------------------------------ 2 Hardware List-------------------------------------------------- ------ Parts List----------------------------------------------------- ---------- Assembly instructions------------------------------------------... -
Page 3: Important Safety Instructions
Important Safety Instructions Before beginning any fitness program, you should obtain a complete physical examination from your physician. When using exercise equip- ment, basic precautions should always be taken, including the following: * Read all instructions before using the Total Hip These instructions are written to ensure your safety and to protect the unit. -
Page 4: Exploded View Diagram
T8009 Total Hip Exploded View Diagram... -
Page 5: Hardware List
Hardware List 1 10 14 0 Millimeters Inches... -
Page 6: Parts List
Parts List Item No. Description QTY Item No. Description Main Upright Plastic Washer Little Main Upright 3.5" Pulley Swing Tube Cable Pivot Arm Gimbal Cross Base Plastic Cap Adj. Base Plastic Collar Foot Pad Rear Side Cover Short Guide Rod Allen Bolt M12×65 Pop Pin Handle Allen Bolt M10×115... -
Page 7: Assembly Instructions
Assembly instructions Assembly of the Total Hip takes professional installers about 2 hours. If this is the first time you have assembled this type of equipment, plan to spend more time. It is strongly recom men ded to assemble the equipment by professional installers. You may find it quicker, safer, easier to assemble this equipment with the help of a friend, as some of components may be large, heavy or awkward to handle alone. - Page 8 Step1 Install the Adj. Foot Plates Align the Adj. Foot Plates (#37) to the Main Upright(#01), Right Support(#10) and Left Support(#11),then secure them by hands.
- Page 9 Step2 Install the Frame 1)Attach the Left Support(#11) to Main Upright(#01) using: Two Allen Bolts M10×95(#56) Two Nylon Locknuts M10(#66) Four Washers 11× 20×2(#69) Φ Φ 2)Attach the Right Support(#10) to Main Upright(#01) using: Two Allen Bolts M10×95(#56) Two Nylon Locknuts M10(#66) Four Washers Φ...
- Page 10 Step3 Install the Frame 1)Attach the Cross Base(#05) to the Right and Left Support(#10,#11) and the Main Support(#01) using: Six Allen Bolts M10×75(#58) Six Nylon Locknuts M10(#66) Twelve Washers 11× 20×2(#69) Φ Φ 2)Attach the Adj. Base to the Right and Left Support (#10,#11) using: Four Allen Bolts M10×80(#57) Four Nylon Locknuts M10(#66)
- Page 11 Step4 Install the Weight Plates 1)Insert both the Guide Rods(#19) into the Main Upri- ght(#01). 2)Slide the Weight Rubber Bumper(#44) down onto each Guide Rod(#19) 3)Carefully begin sliding the Weight Plate one by one sequence:#41,#40,#39. 4)Align both top ends of the Guide Rods(#27) to the Main Upright (#01) and secuer them using: Two Allen Bolts M10×75(#58)
- Page 12 Step5 Install the Little Main Upright Attach the Little Main Upright(#02) to the Main Upright (#01) using: Four Allen Bolts M10×115(#55) Four Nylon Locknuts M10(#66) Eight WashersΦ 11× 20×2(#69) Φ...
- Page 13 Step6 Install the Cam and Roller 1)Install the Cam(#24),the Spacer(#27)and the Pivot Arm(#04) to the Little Main Upright(#02) in sequence, then secure them using: One Allen Bolt M10×25(#62) One Spring Washer Φ 10(#73) One Washer 11× 20×2(#69) Φ Φ One Shaft End(#34) 2)Insert the Swing Tube(#03) into Pivot Arm(#04),then secure using: One Allen Bolt M10×25(#62)
- Page 14 Step7 Route the Cable 1)Insert the bolt of Cable(#49) to the Top Plate(#39), make sure the clip of the Weight Pin are on Top Plate (#39). 2)Route the Cable(#49) up and over the 4.5” and 3.5” lley,then secure them to the Main Upright(#01) using: Two Allen Bolts M10×55(#60) Two Allen Bolts M10×45(#61) Four Nylon Locknuts M10(#66)
- Page 15 Step8 Install the Foot Pad 1)Attach the Root Base(#15) to the Foot Pad(#07) using: Two Allen Bolts M10×70(#59) Two Nylon Locknuts M10(#66) Four Washers 11× 20×2(#69) Φ Φ 2)Install both the Root Base(#15) and the Foot Pad(#07) onto the Adj. Base(#06),insert both Short Guide Rod (#08) into the Foot Pad(#07) and the the Adj.
- Page 16 Step9 Install the Right/Left Rail ,the Safety Tube and the Thick Pop Pin 1)Attach the Above Cross(#14) onto the Right/Left Sup- port,then attach the Left Rail(#12) to the Main Upright (#01) using: Two Allen Bolts M10×115(#55) Two Nylon Locknuts M10(#66) Four Washers 11×...
- Page 17 Step10 Install the Covers 1)Attach the Base Cover to the Right/Left Support (#10, #11) using: Six Chamfer Bolts M6 15(#65) × Six Washers Φ × Φ 18 1.6(#71) × 2)Attach the Little Cover(#18) to the Above Cross(#14) and the Right/Left Support(#10/#11) using: Four Chamfer Bolts M6 15(#65) ×...
- Page 18 Step11 Install the Decal Plates 1)Attach the two Decal Plates(#17,#22) to the Main right(#01) using: Fourteen Buttons (#88) 2)Attach the Weight Shroud(#23) to the Main Upright (#01) using: Four Bolt Covers (#46) Four Chamfer Bolts M5×10(#87) Four Plastic Washers(#47) 3)Insert one Chamfer Bolt M6×15(#65) into the Main right then secure the Plastic Cap(#51) to the Main Up right(#01) using: One Chamfer Bolt M6×15(#65)
Need help?
Do you have a question about the IT8009 Total Hip and is the answer not in the manual?
Questions and answers