Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Impulse IT8005
Summary of Contents for Impulse IT8005
- Page 1 T8005 Leg Extension Assembly Instructions...
-
Page 2: Table Of Contents
Table of contents Important Safety Instructions--------------------------------- 1 Exploded View Diagram------------------------------------------ 2 Hardware List-------------------------------------------------- ------ Parts List----------------------------------------------------- ---------- Assembly instructions------------------------------------------... -
Page 3: Important Safety Instructions
Important Safety Instructions Before beginning any fitness program, you should obtain a complete physical examination from your physician. When using exercise equip- ment, basic precautions should always be taken, including the following: * Read all instructions before using the Leg Extension These instructions are written to ensure your safety and to protect the unit. -
Page 4: Exploded View Diagram
I 8005 Leg Extension Exploded View Diagram... -
Page 5: Hardware List
Hardware List 1 10 14 0 Millimeters Inches... -
Page 6: Parts List
Parts List Item No. Description QTY Item No. Description Main Upright Grip Seat Frame Weight Pin Upper Cross Cable Low Cross Button Swing Tube Half-pulley Cover Adj. Shaft Weight Rubber Bumper Pivot Arm Angle Support Back Pad Support Rubber Cap Handle Plastic Washer Bolt Cover... -
Page 7: Assembly Instructions
Assembly instructions Assembly of the Leg Extension takes professional installers about 2 hours. If this is the first time you have assembled this type of equipment, plan to spend more time. It is strongly recom mended to assemble the equipment by professional installers. You may find it quicker, safer, easier to assemble this equipment with the help of a friend, as some of components may be large, heavy or awkward to handle alone. -
Page 8: Adj. Foot Plate 4
Step1 Install the Adj. Foot Plates Align the Adj. Foot Plates(#11) to the Main Upright(#1) and the Seat Frame(#2) then secure them by hands. - Page 9 Step2 Assemble The Frame 1)Attach the Upper Cross(#3) and the Low Cross(#4)to the Main Upright(#1)using: four Allen Bolts(#62) M10×115 four Nylon Locknuts(#78) M10 eight Washers(#76) Φ 11× 20×2 Φ 2)Attach the Seat Frame(#2) to the Low Cross(#4)and the Upper Cross(#3) using: four Allen Bolts(#65) M10×70 eight Washers(#76) Φ...
- Page 10 Step3 Assemble The Handle Align the Handle(#9) to the Seat Frame(#2), secure it using: two Allen Bolts(#61) M10×125 four Washers(#76) Φ 11× 20×2 Φ two Nylon Locknuts(#78) M10...
- Page 11 Step4 Assemble The Pivot Arm 1)Attach the Pillow Block(#12) to the Main Upright(#1) using: two Allen Bolts(#60) M12×40 four Washers(#75) Φ 13× 26×1.5 Φ two Nylon Locknuts(#77) M12 2)Insert the Adj.Shaft (#6) through the Pillow Block (#12) and the Main Upright(#1). Note: The Swing Tube(#5), the Adj.
- Page 12 Step5 Assemble The Cam Insert the Adj. shaft(#6) through the Main Upright(#1), the Spacer(#17) and the Cam(#10),next, secure the Cam(#10) to the Adj. Shaft(#6) using the Key (#19).
-
Page 13: Short Spacer 1
Step6 Assemble The Pillow Block 1)Insert the Short Spacer (#18) onto the Adj. Shaft(#6). 2)Attach the Pillow Block(#12) to the Main Upright(#1) using: two Allen Bolts(#60) M12×40 four Washers(#75) Φ 13× 26×1.5 Φ two Nylon Locknuts(#77) M12 3)Secure the Adj. Shaft(#6) to the Pillow Block(#12) using: one Allen Bolt(#69) M10×25 one Spring Washer(#79) -
Page 14: Washer(
Step7 Assemble The Angle Support 1)Attach the Angle Support(#54) to the Adj. Shaft(#6) using: one Allen Bolt(#69) M10×25 one Washer(#76) Φ 11× 20×2 Φ one Spring Washer(#79) Φ one Shaft End(#21) 2)Attach the Angle Support(#54) to the Low Cross(#4) using: two Allen Bolts(#65) M10×70 four Washers(#76) Φ... -
Page 15: Guide Rod(
Step8 Assemble The Weight Plates 1)Insert both the Guide Rods(#26) into the Main Upright (#1). 2)Slide the Weight Rubber Bumper(#53) down onto each the Guide Rod(#26). 3)Carefully begin sliding the Weight Plate one by one in sequence:#41,#42,#43,#47. 4)Align both top ends of the Guide Rods(#26) to the Main Upright(#1) and secure them using: two Allen Bolts(#64) M10×75 two Rubber Caps(#55) - Page 16 Step9 Route The Cable 1)Put the clip tied on the weight pin leash onto the Top Plate(#47) as shown,next connect the Cable(#50) to the Top Plate(#47). 2)Route the Cable(#50) up and over the two Pulleies A (#27).then secure them to the Main Upright(#1) using: two Allen Bolts(#67) M10×45 four Washers(#76) Φ...
-
Page 17: Front Decal Plate 1
Step10 Assemble The Decal Plates 1)Attach the two Decal Plates(#30,#31) to the Main Up- right(#1) using: fourteen Butttons(#51) 2)Attach the Weight Shroud (#28)to the Main Upright (#1) using: four Bolt Covers(#57) four Plastic Washers(#56) four screws(#72) M5×10 The Front Decal Plate(#30) with the exercise inst - ctions printed on it should be attached in the front Note of the Main Upright(#1). -
Page 18: Seat Pad(
Step11 Assemble The Pads 1)Attach the Back Pad(#29) to the Back Pad Support(#8) using: one Allen Bolt(#64) M10×75 three Washers(#76) Φ 11× 20×2 Φ two Allen Bolts(#68) M10×30 2)Attach the Seat Pad(#32) to the Seat frame(#2) using: four Washers(#76) Φ 11×...
Need help?
Do you have a question about the IT8005 and is the answer not in the manual?
Questions and answers