Download
Share
Print this page
  1. Manuals
  2. Brands
  3. EZ-ACCESS Manuals
  4. Lifting Systems
  5. Pathway MSTAIR2839
  6. Assembly manual

EZ-ACCESS Pathway MSTAIR2839 Assembly Manual

Modular stair for use with the modular ramp system
Hide thumbs

Advertisement

Quick Links

Download this manual
Assembly Manual
Pathway® Modular Stair
For use with the Pathway® Modular Ramp System
LIFETIME WARRANTY. Please register at www.ezaccess.com/warranty-satisfaction.
®
© EZ-ACCESS
, a division of Homecare Products, Inc. All rights reserved. All text and images contained in
this document are proprietary and may not be shared, modified, distributed, reproduced, or reused without the
®
express written permission of EZ-ACCESS
, a division of Homecare Products, Inc.
Manufactured in the USA
11960 REV 08-25-17

Advertisement

loading
Need help?

Need help?

Do you have a question about the Pathway MSTAIR2839 and is the answer not in the manual?

Questions and answers

Related Manuals for EZ-ACCESS Pathway MSTAIR2839

Summary of Contents for EZ-ACCESS Pathway MSTAIR2839

  • Page 1 , a division of Homecare Products, Inc. All rights reserved. All text and images contained in this document are proprietary and may not be shared, modified, distributed, reproduced, or reused without the ® express written permission of EZ-ACCESS , a division of Homecare Products, Inc. Manufactured in the USA...
  • Page 2 ASSEMBLY MANUAL ® For EZ-ACCESS Pathway® Modular Stair ATTENTION INSTALLER: • For residential use only • 850 lb. weight capacity • Read and follow all instructions, labels and warnings prior to assembly and use • Please leave this ASSEMBLY MANUAL with the end user ATTENTION END USER: •...

  • Page 3: Inspection Before Use

    IMPORTANT! Read and Follow All Instructions and Warnings Before Use! INSPECTION (BEFORE USE) • Read and follow all labels, instructions, and warnings prior to assembly and use. To obtain a copy of complete instructions and warnings, call customer service at 1-800-451-1903. •...

  • Page 4: Basic System Components

    INTRODUCTION The Pathway® Modular Stair is designed to work in conjunction with the Pathway® Modular Ramp System but can be used as a standalone stair on an existing porch or deck. There are five models which cover different height ranges from 11” to 56”. For instance the Model MSTAIR2839 can be used for heights between 28” and 39”...
  • Page 5 ASSEMBLING THE RISER 2.1. Lay the right hand stair side rails flat with tread channel cleats pointing up and insert the treads into the channel cleats. Place on cardboard or other suitable surface to avoid scratching the side rail. Make sure the tread is positioned with the traction ridges oriented upward.
  • Page 6 2.3. Set the left hand side rail on the treads and tap into place until the holes in the channel cleat line up with the holes in the tread (FIG.3). FIG. 3 2.4. Install 5/16”-18 x 2-1/4” carriage bolts with nuts and washers in the left side rail and through the tread, as described in 2.2.
  • Page 7 FIG. 5 3.3. Hang the stair assembly on the platform in the desired location. Adjust the vertical position of the riser on the legs and top posts by loosening and retightening the 3/8”-16 set screws in the riser corner pockets until the distance from bottom tread to ground is approximately the same distance from top tread to the platform walking surface and the stair treads are level.
  • Page 8 FIG. 7 3.5. Insert the stair bottom posts in bottom corner pockets with the holes on top and oriented as shown in FIG. 8. Do not tighten set screws yet. FIG. 8 IMPORTANT: If the optional kit is used, the closure CONNECTOR –...
  • Page 9 3.7. Insert the elbow half with the internal set screw into both ends of each tube. Make sure the elbow side for the assembly screw is oriented in the same direction and the flat portions of the elbow halves are parallel on both ends of the handrail tube then tighten the internal set screw securely using a T-Handle Allen wrench or similar tool.
  • Page 10 3.8. Reassemble the closure elbows but do not tighten the elbow assembly screw fully. The elbow halves which will attach to the stair posts should be at 90 degrees and oriented in the same direction at both ends. 3.9. Attach handrails to the tread side of the stair top and bottom posts with the elbow assembly screws on top using 5/16”-18 x 2”...
  • Page 11 INSTALLING THE CONNECTOR – HR PLATFORM TO HR STAIR (MHRPSC) 4.1. When using the to connect a stair top post CONNECTOR – HR PLATFORM TO HR STAIR (MHRPSC) to a platform handrail post, closure elbows must be attached to the stair top post before the stair handrails are attached.
  • Page 12 4.4. Position the closure elbow attached to the stair top post so it is aligned with the closure elbow attached to the platform handrail post (but do not tighten fully) then measure the distance between the two larger round faces. The gap between the upper and lower closure elbows should be the same but it is advisable to check both before cutting the tubes to fit (FIG.14).
  • Page 13 FIG. 15 4.12. Double check that all fasteners are tightened securely. Periodically check for ground shifts and regularly check and tighten hardware as needed. - 13 -...

  • Page 14: Warranty And Registration

    WARRANTY & REGISTRATION ® EZ-ACCESS , a division of Homecare Products, Inc., (herein referred to as Manufacturer), warrants that the equipment shall be free from defects in material and workmanship under normal use and service for a period of 3- years from the date of original purchase.