Lighting Instructions; Match Lighting - Temco PVF7400 Series Installation And Operating Instructions Manual

Temco PVF7400 Series
WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage,
personal injury or loss of life.
A. This appliance has a pilot which must be lighted by hand.
When lighting the pilot, follow these instructions exactly.
B. BEFORE OPERATION smell all around the appliance area
for gas. Be sure to smell next to the floor because some
gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS:
•
Do not try to light any appliance.
•
Do not touch any electrical switch; do not use any tele-
phone in your building.
•
Immediately call your gas supplier from a neighbor's
telephone.
•
Follow the gas supplier's instructions.
1. STOP! Read the safety information above before proceed-
ing.
2. Refer to Figure 24. To turn off the gas supply, depress the
knob slightly and turn clockwise
3. Wait five (5) minutes to clear out any gas. Then smell for
gas, including near the floor. If you smell gas, STOP!
Follow "B" in the safety information above. If you don't
smell gas, go to the next step.
Fig. 24
Fig. 26
4. Refer to Figure 25. Locate the
pilot.
5. Refer to Figure 26. Push in the
control knob and turn counter-
clockwise to the PILOT
position. Hold the control knob
in for a few seconds.
Depress the control knob slightly and turn it clockwise
If the pilot cannot be ignited with the piezo, it can be
manually lit with the use of a match and lighter rod.
1. Place the match in the holder and light. With the right
hand, depress and turn the control knob counterclock-
wise to the PILOT position. Hold in for 20
seconds.
16
For Your Safety, Read Before Lighting

Lighting Instructions

to the OFF position.
Fig. 28
OFF
PILOT ON
Fig. 25
To Turn OFF Gas to Appliance

Match Lighting

•
If you cannot reach your gas supplier, call the fire depart-
ment.
C. Use only your hand to push in or turn the gas control knob.
Never use tools. If the knob will not push in or turn by
hand, don't try to repair it. Call a qualified service techni-
cian. Force or attempted repair may cause a fire or an
explosion.
D. Do not use this appliance if any part of it has been under
water. Immediately call a qualified service technician to
inspect the appliance and to replace any part of the control
system or gas control which has been under water.
E. Be sure both the receiver and the remote have had a 9 volt
battery installed in each.
6. While still holding in the control
knob, press the ignitor push-
button several times. This will
cause a spark at the pilot which
will ignite the pilot gas. (Fig. 27)
7. Hold the control knob for 60
seconds to prevent the flame
failure detector from shutting off
the gas while its probe is warming up.
8. Release the control knob.
•
If the knob does not pop up when released, stop and
immediately call your service technician.
•
If the pilot will not stay lit after several tries, turn the gas
control knob to OFF and call your service technician or gas
supplier.
9. When the pilot remains lit, turn the control knob counter-
T151
clockwise
10. Lighting Instructions for Millivolt Wall Switch. After the pilot is
lit and the control knob is released, the wall swtich can be
switched to turn the unit ON or switched to turn it OFF.
Refer to Page 14 for wiring.
to the OFF position. Refer to Figure 24.
2. Take the lighter rod and lighted match and ignite the pilot.
3. Continue to hold the control knob for an additional 20
seconds to ensure pilot is maintained.
4. Proceed with Step 8 in the Lighting Instructions.
Fig. 27
Piezo
to the ON position. (Fig. 28)
78186