Table of Contents
Advertisement
INSTALLER/CONSUMER
SAFETY INFORMATION
PLEASE READ THIS MANUAL
BEFORE INSTALLING AND
USING APPLIANCE
WARNING!
IF THE INFORMATION IN THIS
MANUAL IS NOT FOLLOWED
EXACTLY, A FIRE OR
EXPLOSION MAY RESULT
CAUSING PROPERTY DAMAGE,
PERSONAL INJURY OR LOSS
OF LIFE.
FOR YOUR SAFETY
Installation and service must
be performed by a qualified
installer, service agency or the
gas supplier.
WHAT TO DO IF YOU SMELL GAS:
•
Do not try to light any appliance.
•
Do not touch any electric switch;
do not use any phone in your
building.
•
Immediately call your gas
supplier from your neighbor's
phone. Follow the gas suppliers
instructions.
•
If you cannot reach your gas
supplier call the fire department.
DO NOT STORE OR USE
GASOLINE OR OTHER
FLAMMABLE VAPORS AND
LIQUIDS IN THE VICINITY OF
THIS OR ANY OTHER
APPLIANCE.
WARNING: Improper installation,
adjustment, alteration, service or
maintenance can cause injury or
property damage. Refer to this
manual. For assistance or additional
information, consult a qualified
installer, service agency or the gas
supplier.
Builder Top Vent Direct
Vent Zero Clearance Gas
Fireplace Heater
Models: 33TDVDSN,
36TDVDSN,
39TDVDSN
Installation Instructions and
Homeowner's Manual
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
7636
TDVN cover
5/04
20007890 5/08 Rev. 8
C E RT I F I E D
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Temco 33 TDVDSN
Summary of Contents for Temco 33 TDVDSN
- Page 1 INSTALLER/CONSUMER SAFETY INFORMATION PLEASE READ THIS MANUAL BEFORE INSTALLING AND USING APPLIANCE WARNING! Builder Top Vent Direct IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED Vent Zero Clearance Gas EXACTLY, A FIRE OR EXPLOSION MAY RESULT Fireplace Heater CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS Models: 33TDVDSN, OF LIFE.
-
Page 2: Table Of Contents
TDVDSN Series Direct Vent Gas Fireplace Table of Contents PLEASE READ THE INSTALLATION & OPERATING INSTRUCTIONS BEFORE USING THIS APPLIANCE. Thank you and congratulations on your purchase of a CFM Corporation fireplace. IMPORTANT: Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may result in a possible fire hazard and will void the warranty. -
Page 3: Installation & Operating Instructions
TDVDSN Series Direct Vent Gas Fireplace Installation & Operating Instructions 13. This fireplace must not be connected to a chimney flue This gas fireplace should be installed by a qualified installer, serving a separate solid fuel burning fireplace. preferably NFI or WETT (Canada) certified, in accordance with 14. -
Page 4: Requirements For The Commonwealth Of Massachusetts
TDVDSN Series Direct Vent Gas Fireplace Installation & Operating Instructions Inspection Requirements for the Commonwealth of Massachusetts The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not All gas fitting and installation of this heater shall only be approve the installation unless, upon inspection, the done by a licensed gas fitter or licensed plumber. -
Page 5: Fireplace Dimensions
TDVDSN Series Direct Vent Gas Fireplace Fireplace Dimensions Rough Opening Depth N- Rough Opening Width Rough Opening Height Electrical Access Gas Line Voltage Access Electrical Access 1" (25mm) Gas Line Access 7636 7636 Fig. 1 Fireplace specifications and framing dimensions. TDVN specs 5/04... -
Page 6: Locating Your Fireplace
TDVDSN Series Direct Vent Gas Fireplace Locating Your Fireplace Fireplace Top Louvre Assembly LU584-T Top of Fig. 2 Locate gas fireplace. Combustion LU584-T Locating unit Chamber A - Flat on wall B - Cross corner C - **Island 12/18/02 djt CFM146 Bottom of Door Trim D - Room divider... -
Page 7: Hearth
TDVDSN Series Direct Vent Gas Fireplace Hearth Final Finishing A hearth is not mandatory but is recommended for Noncombustible materials such as brick or tile may be aesthetic purposes. We recommend a noncombustible extended over the edges of the face of the appliance. hearth which projects out 12”... -
Page 8: Gas Line Installation
TDVDSN Series Direct Vent Gas Fireplace 5. For natural gas, a minimum of 3/8” iron pipe with a Gas Line Installation gas supply pressure of 4.5” w.c. (from the gas me- ter). Consult with local gas utility and ANSI Z223.1/ When purging gas line, the front window NFPA 54 if any questions arise concerning pipe frame assembly must be removed. -
Page 9: General Venting
TDVDSN Series Direct Vent Gas Fireplace The EB-1 Electrical junction box has been fitted stand- INSIDE ard on this model to allow for the easy connection of an Electrical Box optional fan kit. Retaining Screw To connect the EB-1 box to the house electrical supply follow the steps below. -
Page 10: General Venting Information-Termination Location
TDVDSN Series Direct Vent Gas Fireplace General Venting Information - Termination Location INSIDE CORNER DETAIL ����� ������ Fixed Operable Closed CFM145a AREA WHERE TERMINAL IS NOT PERMITTED VENT TERMINATION AIR SUPPLY INLET Canadian Installations US Installations A = Clearance above grade, veranda, porch, CFM145a 12”... -
Page 11: General Information On Assembling Vent Pipes
TDVDSN Series Direct Vent Gas Fireplace Termination Clearances Termination clearances for buildings with combustible and noncombustible exteriors. Inside Corner Alcove Applications* Outside Corner Combustible 6" (152 mm) Combustible 6" (152 mm) Noncombustible 2" (51 mm) Noncombustible 2" (51 mm) Balcony - Balcony - with no side wall with perpendicular side wall... -
Page 12: Twist Lock Pipes
TDVDSN Series Direct Vent Gas Fireplace Twist Lock Pipes When using CFM Corporation twist-lock pipe it is not necessary to use sealant on the joints. The only areas of the venting system that need to be sealed with high temperature silicone sealant are the collars on the fireplace and termination, and the sliding joint of any telescopic vent section used in the system. - Page 13 TDVDSN Series Direct Vent Gas Fireplace 20' (6m) Pipe Straps Every 3’ (914mm) Pipe Straps 1 x 90° elbow in horizontal plane = 3’ (914mm) Every 3’ (914mm) Firestop/Zero Clearance Sleeve FP1012 Fig. 11 Support straps for horizontal runs. FP1238 Horizontal plane means no vertical rise exists on this FP1012 portion of the vent assembly.
- Page 14 TDVDSN Series Direct Vent Gas Fireplace Vent Opening for Combustible Wall 9³⁄₈” (240mm) Framing Detail 9³⁄₈” (240mm) Fireplace Hearth Opening for Noncombustible Wall FP1240 7¹⁄₂” (190mm) Fig. 17 Vertical height requirement. VO584-100 of the inner and outer elbow. Again secure joints with Fig.
- Page 15 TDVDSN Series Direct Vent Gas Fireplace Support horizontal pipes every 3’ (914 mm) with metal pipe straps. Make sure the horizontal vent pipe is in- stalled on a level horizontal plane. Vertical Sidewall Installation Flex Vent Pipe NOTE: The 40” (1016 mm) flex vent is used for 90° off the top of the unit then out the back wall.
-
Page 16: Below Grade Installations
TDVDSN Series Direct Vent Gas Fireplace Step 4 window well (not supplied). Refill hole with 12” (305 Install the 4” (102 mm) flex vent pipe to the termination mm) of coarse gravel leaving a clearance of approxi- cap collar as described on Page 11. mately 4”... -
Page 17: Vertical Through-The-Roof Applications & Installation
TDVDSN Series Direct Vent Gas Fireplace Vertical Through-the-Roof Applications This Gas Fireplace has been approved for: • Vertical installations up to 40’ (12 m) in height. Up Max. 8' (2.4m) to a 10’ (3 m) horizontal vent run can be installed within the vent system using a maximum of two 90°... -
Page 18: Vertical Restrictor Plate (33Tdvdsn Only)
TDVDSN Series Direct Vent Gas Fireplace Vertical Restrictor Plate Attic Insulation (33TDVDSN only) Shield When installing the 33TDVDSN with a Vertical Through- the-Roof configured flue system the restrictor plate, (#10002495) supplied with the appliance MUST BE Joist FITTED TO THE APPLIANCE at installation. Install restrictor plate to firebox top using two (2) screws. - Page 19 TDVDSN Series Direct Vent Gas Fireplace If there is a room above ceiling level, firestop spacer must be installed on both Min. 2’ (610 mm) the bottom and the top side of the ceiling joists. If an attic is above ceiling level a 7DVAIS (Attic Insulation Shield) must be installed.
-
Page 20: Venting Components
TDVDSN Series Direct Vent Gas Fireplace Twist Lock Venting Components 7TDVSK - Through the wall Top Vent Termination Starter Kit - 584A Model 7TDVSK - Sidewall Venting (Twist Lock Pipe) venting components rear vent term Model 7FDVSK - Sidewall Venting (Flex Vent Pipe) 4/6/99 djt Starter Kit - Model 7TDVSKV - Vertical Venting for 7TDVSKV-A order 1/12 to 6/12 roof pitch... -
Page 21: Operating Instructions
TDVDSN Series Direct Vent Gas Fireplace Operating Instructions Glass Information Only glass approved by CFM Corporation should be used on this fireplace. • The use of any non-approved replacement glass will void all product warranties. • Care must be taken to avoid breakage of the glass. •... -
Page 22: Installation Of Logs, Lava Rock & Ember Material
TDVDSN Series Direct Vent Gas Fireplace Installation of Logs, Lava Rock & Ember Material Unpack the logs from packaging and remove each log from its wrapping materials. The logs are fragile and should be handled with care. Keep the packaging material out of the reach of children and dispose of the material in a safe manner. -
Page 23: Valve Wiring
TDVDSN Series Direct Vent Gas Fireplace ON/OFF Wall Switch or 120 Volt Thermostat (by Others) Junction Box 120 VAC Line BLACK WHITE 120 VAC RTN Wire to Unit By Others GREEN BLACK VALVE MAIN GREEN GROUND WHITE BLACK VALVE MAIN DS2070S MODEL CONTROLS... -
Page 24: Lighting & Operating Instructions
TDVDSN Series Direct Vent Gas Fireplace Lighting and Operating Instructions FOR YOUR SAFETY READ BEFORE LIGHTING WARNING:If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. • A. -
Page 25: Troubleshooting
TDVDSN Series Direct Vent Gas Fireplace Troubleshooting NOTE: Before troubleshooting the gas control system, be sure external shut off is in the “ON” position. WARNING: Before doing any gas control service work, remove glass front! Problem Possible Cause Solution No gas to main burner Low gas pressure to With the main burner functioning, adjust the inlet the appliance. -
Page 26: Fuel Conversion Instructions
TDVDSN Series Direct Vent Gas Fireplace Fuel Conversion Instructions WARNING: This conversion kit must ONLY be ap- plied as part of a conversion kit supplied by the appliance manufacturer for the specific appliance and type of gas being converted. The conversion shall be carried out in accordance with the requirements of the provincial authori- Burner Tabs ties having jurisdiction and in accordance with the... - Page 27 TDVDSN Series Direct Vent Gas Fireplace Kit Number Conversion Parts Included with Kit 20007864 20007891 20007903 Main Burner Orifice - LP 76776 20007908 20007907 Label, Conversion 10002876 10002876 10002876 5. Check the air shutter opening for the corresponding Valve Conversion gas used.
-
Page 28: Unit Adjustment
TDVDSN Series Direct Vent Gas Fireplace Unit Adjustment Once installed, the unit should be operated at least High Altitude three (3) times to ensure that all is in working order. When installing this fireplace at an elevation between NOTE: Manufacturing oils will smoke during initial firing 0 and 2000 feet (0 - 610m) in the USA and 0 and 4500 of appliance. -
Page 29: Maintenance
TDVDSN Series Direct Vent Gas Fireplace Maintenance Motor and Blower for Fan Kit (optional) After the logs are removed allowing access to the burn- er area, use a vacuum cleaner to carefully remove dust This motor has been factory oiled and under normal and loose particles from the base, logs and from around operating conditions should not require oiling. -
Page 30: Air Shutter
TDVDSN Series Direct Vent Gas Fireplace Normal and High Direct Vent Units - Inputs - Orifice Size - Altitude BTU/Hr Manifold Pressure Orifice 0 - 2000ft. Altitude in USA Model Max. Input @ Max. Orifice 0-4500ft Altitude in Canada 33TDVDSN 18,000 3.5”w.c. -
Page 31: Replacement Parts
TDVDSN Series Direct Vent Gas Fireplace 33TDVN Logs 36/39TDVN Logs CFM Corporation reserves the right to make changes in design, materials, specifications, prices and discontinue colors and products at any time, without notice. TDVDSN/TDVDSP Series Gas Fireplace 7890 Units: GF1HT1, GF1HT2, GF1HT3 TDVDSN parts Ref. - Page 32 TDVDSN Series Direct Vent Gas Fireplace TDVDSN Series Gas Fireplace Heater (continued) Ref. Description 33TDVDSN 36TDVDSN 39TDVDSN DS Ignition Control (Synetek DS2070S) 20007288 20007288 20007288 Spark Electrode w/Wire 72935 72935 72935 Front Grate Assembly 20008141 20008141 20008141 Manifold Tube (w/Fittings and Orifice) (not shown) 20007736 20007685 20007735...
-
Page 33: Optional Accessories
TDVDSN Series Direct Vent Gas Fireplace Optional Accessories Fan Kits Thermal Sen- FK24 Fan Assembly This auxiliary fan system increases the efficiency of the circulation of the heating air. The FK24 fan kit allows variable speed control of the circulation fan and also incorporates a heat sensor in the circuit. -
Page 34: Wiring Instructions
TDVDSN Series Direct Vent Gas Fireplace 5. Place the rear refractory panel in place. Wiring Instructions 6. Slide the side refractory panels into place to hold the rear panel secure. Adjust the top adjustable tabs The fireplace, when installed, must be electrically connected and grounded in to hold the side panel against the firebox wall and accordance with local codes or, in the... -
Page 35: Bay Window Screen
TDVDSN Series Direct Vent Gas Fireplace Top Louvre Window Frame Ceramic Ceramic Refractory Refractory Bottom Louvre As- semblies Bottom Brass Trim CFM178 Fig. 50 Bay window screen assembly. FP1234 Screws Fig. 49 Bay window installation. CFM178 Remote Controls Bay Window Screen 8/17/01 Bay Window Screen Optional remote control units are available to control... -
Page 36: Warranty
TDVDSN Series Direct Vent Gas Fireplace One Year Limited Warranty TEMCO Fireplace Products Vented Gas Fireplaces This warranty is limited to TEMCO Fireplace Products mitted along with proof of purchase to obtain prior Vented Gas Fireplaces (henceforth, Product) manufac- approval for warranty repair or replacement and to af- tured by CFM Corporation (henceforth, CFM). -
Page 37: Installation And Startup Checklist
TDVDSN Series Direct Vent Gas Fireplace TEMCO FIREPLACE PRODUCTS DIRECT VENT FIREPLACES INSTALLATION AND STARTUP CHECKLIST Customer Copy NOTE: TEMCO Fireplace Products gas logs and fireplaces require installation by a qualified gas appliance installer. A copy of this checklist must be submitted, along with proof of purchase, when applying to Technical Services for prior written approval of warranty repair or replacement. - Page 38 TDVDSN Series Direct Vent Gas Fireplace TEMCO FIREPLACE PRODUCTS DIRECT VENT FIREPLACES INSTALLATION AND STARTUP CHECKLIST Installer’s Copy NOTE: TEMCO Fireplace Products gas logs and fireplaces require installation by a qualified gas appliance installer. A copy of this checklist must be submitted, along with proof of purchase, when applying to Technical Services for prior written approval of warranty repair or replacement.
-
Page 39: Warranty Registration
TDVDSN Series Direct Vent Gas Fireplace Customer Copy Serial # ______________________________________ Model # ______________________________________ I certify that I have followed all codes and regulations and adhered to the TEMCO Fireplace Products installation instructions. I have completed the proper installation and startup checklist. Installer’s Signature Print Installer’s Name Purchaser _____________________________________... -
Page 40: Energuide
Efficiency Ratings Model EnerGuide Ratings Fireplace Efficiency (%) 33TDVDSN 57.9 33TDVDSP 57.9 36TDVDSN 58.51 36TDVDSP 58.51 39TDVDSN 39TDVDSP CFM Corporation 2695 Meadowvale Blvd. • Mississauga, Ontario, Canada L5N 8A3 800-668-5323 • www.cfmcorp.com...
Need help?
Do you have a question about the 33 TDVDSN and is the answer not in the manual?
Questions and answers