Table of Contents
Advertisement
Quick Links
TEMCO FIREPLACE PRODUCTS, Inc.
Installation and Operating Instructions for Gas Log Heaters
Models ending with "N" use natural gas; models ending with "P" use propane (LP) gas.
This
appliance
unvented room heater certified under
ANSI Z21.11.2-2000 when fitted to a
solid fuel burning masonry or factory
built fireplace with the flue damper
closed.
It
also
decorative
appliance
Z21.60a-2000.CGA 2.26a-2000,
fitted to a solid fuel burning masonry
or factory built fireplace with the flue
damper open.
State or local codes
may
only
allow
appliance in a vented configuration.
If the information in this manual is not followed exactly, a fire or explosion may result
•
Do not store or use gasoline or other flammable vapors and liquids in the vicinity
of this or any other appliance.
•
Do not try to light any appliance.
•
Do not touch any electric switch; do not use any phone in your building.
•
Immediately call your gas supplier from a neighbor's phone. Follow the gas
supplier's instructions.
•
If you cannot reach your gas supplier, call the fire department.
•
Installation and service must be performed by a qualified installer, service agency
or the gas supplier.
This is an unvented gas-fired heater. It uses air (oxygen) from the room in which it is
installed. Provisions for adequate combustion and ventilation air must be provided.
GAS FIRED
UNVENTED
ROOM HEATERS
LISTED
5L24
Models
operates
as
an
operates
as
a
under
ANSI
when
operation
of
this
FOR YOUR SAFETY
WHAT TO DO IF YOU SMELL GAS
PATENT NO. US 6,390.808 B1
PS24MN, PS24MP
WARNING
P.O. Box 1349 Manchester, TN 37349
P.O. Box 1148 Perris, CA 92572
1773 Parque Industrial Cachanilla
Mexicali, B.C. 21600
REV. 10/30/02 10:05 AM
76780M
Advertisement
Table of Contents
Related Manuals for Temco PS24MN
Summary of Contents for Temco PS24MN
- Page 1 TEMCO FIREPLACE PRODUCTS, Inc. Installation and Operating Instructions for Gas Log Heaters Models PS24MN, PS24MP Models ending with “N” use natural gas; models ending with “P” use propane (LP) gas. This appliance operates unvented room heater certified under ANSI Z21.11.2-2000 when fitted to a...
-
Page 2: Table Of Contents
Installation and Startup Checklist ..............................17, 18 Warranty Registration ....................................19 MINIMUM DIMENSIONS FOR EXISTING SOLID FUEL BURNING FIREPLACES. OPENING HEIGHT = H HEARTH SIZE TABLE Opening Height Front Width Rear Width Depth PS24MN 18" 30" 21" 15" PS24MP 18" 30" 21"... -
Page 3: Important Information
IMPORTANT INFORMATION • INSTALLER: Please leave these instructions with the owner. This appliance may be installed in an after-market* OWNER: Please retain these instructions for future reference. manufactured "mobile" home where not prohibited by state or local codes. WARNING: ANY CHANGE TO THIS HEATER OR ITS •... -
Page 4: Provision For Adequate Combustion And Ventilation Air
PROVISIONS FOR ADEQUATE COMBUSTION AND VENTILATION AIR Example: 5,000 cu. ft. (volume of space) ÷ 50 cu. ft. = WARNING: This heater shall not be installed in a 100 or 100,000 (maximum BTU/Hr the space can confined space or unusually tight construction unless support) provisions are provided for adequate combustion 3. -
Page 5: Provisions For Adequate Combustion And Ventilation Air
PROVISIONS FOR ADEQUATE COMBUSTION AND VENTILATION AIR Unusually tight construction is defined as construction If your home meets all of the three criteria above, you must where: provide additional fresh air. a. walls and ceilings exposed to the outside atmosphere You may provide two permanent openings: one within 12"... -
Page 6: Installation
INSTALLATION is inadvertently closed. UNPACKING Clearances Unvented Installation existing Open the carton and remove the logs and the chassis. fireplaces, (jurisdiction permitting) Remove each of the logs by gripping at either end of the log while avoiding any undue pressure. 1. -
Page 7: Gas Connection
MANTEL CLEARANCES (SINGLE OR MULTI-SIDED OPENING FIREPLACES) Minimum Clearance to Wall & Ceiling Figure 4A: Figure 4C: 62” 2” FIREPLACE HEARTH LEVEL Figure 4D: Side Clearances and Projection Figure 4B: WC. This is in addition to the regulator fitted to the heater. GAS CONNECTION All piping must comply with local codes and ordinances or with CHECK GAS TYPE. -
Page 8: Piping Chart
Figure 5 PIPED GAS SUPPLY LESS THAN 6 FEET VALV IF USING FLEXIBLE CHECK LOCAL CODES FOR SPECIFIC REQUIREMENTS All bends in metallic tubing should be smooth, elbows are recommended. CAUTION: Shut off the main gas supply before removing end cap to prevent gas from filling the work area. -
Page 9: Gas Pressure Check
GAS LINE PIPE SIZING NOTE: To determine the size of the branch gas line from the main gas line to the fireplace, enter the tables below (for iron pipe or copper tubing) using the distance from the gas meter or second stage regulator to the furthest appliance on the gas system. -
Page 10: Log Positioning
around the base of the logset DO NOT place WARNING Figure 6A any material, including volcanic DANGER OF PROPERTY DAMAGE, ash on burner, pilot or logs . BODILY INJURY OR DEATH. RETAINING NEVER USE A MATCH OR OPEN FLAME TO TEST FOR CLIP LEAKS. -
Page 11: To Turn Off Gas To Appliance
Figure 7 FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. • A. This appliance has a pilot which must be lighted by hand. When Follow the gas supplier's instructions. -
Page 12: Flame Check
Height of altered in any way. flame should be approximately 3” on high. Figure 22 Figure 21 Figure 23 AIR SHUTTER SETTINGS - DIM “A” MODEL BLUE FLAME YELLOW FLAME “A FRONT BURNER REAR BURNER PS24MN .250 CLOSED PS24MP .437 .250... -
Page 13: Managing Heat Output
MANAGING HEAT OUTPUT The heat output from the appliance can be controlled by the prime function lies in the aes thetic effect of the flames when position of the flue damper on vented fireplaces. installed in a solid fuel burning fireplace with the flue damper open. -
Page 14: Troubleshooting
TROUBLESHOOTING With proper installation and maintenance, your new gas fireplace should provide years of trouble-free service. If you do experience a problem, refer to the trouble shooting guide below. This guide will assist you or a qualified service person in the diagnosis of problems and the corrective action to be taken. -
Page 15: Repair Parts
REPAIR PARTS TEMCO FIREPLACE PRODUCTS, INC. Always include the correct name, part number, model P.O. Box 1349 Manchester, TN 37349 number and serial number of the appliance when ordering TEMCO FIREPLACE PRODUCTS, INC. service parts. Refer to the parts list below. -
Page 16: Warranty Information
ONE YEAR WARRANTY TEMCO warrants all components of the Product to be free of defects in materials and workmanship for a period of one year from the date of installation, with the exception of the warranty on logs and ember base. -
Page 17: Installation And Startup Checklist
INSTALLATION AND STARTUP CHECKLIST Customer Copy NOTE: TEMCO gas logs and fireplaces require installation by a qualified gas appliance installer. A copy of this checklist must be submitted, along with proof of purchase, when applying to Technical Services for prior written approval of warranty repair or replacement. -
Page 18: Installation And Startup Checklist
INSTALLATION AND STARTUP CHECKLIST Installer’s Copy NOTE: TEMCO gas logs and fireplaces require installation by a qualified gas appliance installer. A copy of this checklist must be submitted, along with proof of purchase, when applying to Technical Services for prior written approval of warranty repair or replacement. -
Page 19: Warranty Registration
CUSTOMER COPY Model # __________________________________________ Serial #_________________________________________ I certify that I have followed all codes and regulations and adhered to the TEMCO installation instructions. I have completed the proper installation and startup checklist. Installers Signature Print Installer’s Name WARRANTY REGISTRATION...