Related Manuals for Garudan GF-105 Series
Summary of Contents for Garudan GF-105 Series
- Page 1 User´s Manual GF-105 Serie ANITA B, s.r.o. Hliníky 2068 680 01 Boskovice Czech Republic tel: +420 516 454 774 +420 516 453 496 fax: +420 516 452 751 e-mail: info@anita.cz...
-
Page 2: Table Of Contents
ANITA © Contens 1) SPECIFICATIONS page 3 2) SAFETY RULES FOR MACHINES page 4 3) INSTALLATION 1. Before operation page 6 2. Machine head page 7 3. Lubrication page 7 4. Program Unit page 8 5. Function of reverse feed stitching mechanism page 8 4) CONTROL AND ADJUSTMENT OF THE SEWING MACHINE 1. -
Page 3: Specifications
ANITA © 1) SPECIFICATIONS Model Usage Max speed Max stitch Needle system Presser foot lenght and size (manual/knee) GF-105-143 LM light-medium 5.000 134R(65-110) 6/13mm GF-105-147 LM light-medium 5.000 134R(65-110) 6/13mm GF-105-143 H (HR) heavy 3.500 134R(110-200) 6/13mm GF-105-147 H (HR) heavy 3.500 134R(110-200) -
Page 4: Safety Rules For Machines
ANITA © Serie GF-105... - Page 5 ANITA © Serie GF-105...
-
Page 6: Before Operation
ANITA © 3) INSTALLATION 1. Before operation Serie GF-105... -
Page 7: Machine Head
ANITA © 2. Machine head 1) Machine head Oil tray should be put at the four corners of the slot in the table plate. Fix two arm cushion 1 to the A side of oil tray 3. Fix the two stand bases 2 to the B side of oil tray 3, then fix the oil tray 3 (Fig. 1, 2). -
Page 8: Program Unit
ANITA © 4. Program unit A. Installing automatic knee-lifting solenoid on machine head Use five fixing screws (4) to Stach the solenoid on the back side of machine head (Fig.6) B. Assembling of back cover When the machine is equiped by manual knee-lifter, fasten the briket tightly using the free fixing screws in the back lid of the machine (Fig.6) C. -
Page 9: Needle Insertion
ANITA © 4) CONTROL AND ADJUSTMENT OF THE SEWING MACHINE 1. Needle Insertion With the needle groove (1) facing left, insert the needle tip into the upper end of the stoper hole (2) and osten the needle with the clamp screw (3). (Figbr.9) Fig.9 2. -
Page 10: Lubrication Adjustment Of Hook
ANITA © 5. Lubrication Adjustment of Hook A. Checking the oil supply level of Hook a) After racing the sewing machine for three minutes, secure the oil flowchecking paper as shown in Fig and run the machine for about five seconds. Ten check the oil tape marked on the paper. b) Check the oil supply level three times. -
Page 11: Adjusting The Needle Stop Position
ANITA © 6. Adjusting the Needle Stop position Obr. 13 7. Inserting Lower Thread and Tension Adjustment A. After placing a bobbin (2) in a bobbin case (6), push the thread through the thread groove (3) and hook it under the tension adjusting plate spring (4). To tighten the lower thread, turn the tension adjusting screw (5) clockwise.Turn it counterclockwise to loosen. -
Page 12: Routing Upper Thread
ANITA © 8. Routing upper thread Place the thread také-up lever at the highest position and route the upper thread in the order indicated in Fig.15. Fig.15 Serie GF-105... -
Page 13: Upper Thread Adjustment
ANITA © 9. Upper Thread Adjustment A. Main thread adjustment device The tension of the upper thread gets tighter if the tension adjusting nut (1) as in Fig. 16 is turned in a clockwise direction and it gets looser when turned in the opposite direction. -
Page 14: Height And Tension Adjustment Of Presser Foot
ANITA © 10. Height and Tension Adjustment of Presser Foot A. Aa is Fig.19, remove the rubber plug (2) in the face plate and place the presser foot (3) on the needle plate. Then, loosen the presser bar fixing screw (4) and adjust the height of the presser bar. -
Page 15: Stitch Lenght Adjustment
ANITA © 12. Stitch lenght Adjustment As is shown in Fig.21, the number marked by the stitch adjusting dial (1) signifies the stitch lenght in mm units. Move the dial sideways to set it to the desired stitch lenght (Turn it in clockwise direction and the stitch lenght will decrease while turning it counterclockwise will increase the stitch lenght). -
Page 16: Feed Cam Adjustment
ANITA © 14. Feed Cam Adjustment Fig.24 15. Timing adjustment of Trimmer Fig.25 A. Adjusting the position of the thread trimming cam If you run the handwheel of the machine, the needle bar goes fromthe bottom up to 5 mm, then the thread trimming solenoid (4) is pressed to impel the roller ball touchs to the concave of the thread trimming cam (1). -
Page 17: Adjustment The Thread Take-Up Stroke
ANITA © 16. Adjustment the Thread Take-Up Stroke A. When sewing heavy-weight materials, move thread guide (1) to the left (in direction A) to increase the lenght of thread pulled out by thread take-up. B. When sewing light-weight materials, move thread guide (1) to the right (indirection B) to decrease the lenght of thread pulled out by the thread take-up. -
Page 18: Adjustment Of The Wiper
ANITA © 19. Adjustment of the Wiper 1. Positioning the wiper Adjust the position of the wiper according to the thickness of the material sewn. The adjustment procedure is as follows: a) Turn the handwheel in the normal direction of rotation to align white marker dot (1) on the handwheel with red marker dot (2) on the machine arm. -
Page 19: Winding The Bobbin
ANITA © 20. Winding the Bobbin Thread the bobbin winder and wind the bobbin thread onto the bobbin ilustrated in the Fig. 37. Fig. 37 21. Adjustment of the Pedal Installing the connecting rod . Nastavení úhlu pedálu Sklon pedálu lze jednoduše nastavit pomocí změny délky táhla. Povolte nastavovací šroub (4) a nastavte požadovanou délku táhla. -
Page 20: Pedal Operation
ANITA © 22. Pedal Operation The pedal is operated in the following four steps: 1.The machine runs at low sewing speed when you lightly depress the front part of the pedal (B). 2.The machine runs at high sewing speed when you further depress the front part of the pedal (A). 3.The machine stops (with its needle up or down) When you reset the pedal to its original position ©. -
Page 21: Installing The Thread Stand
ANITA © 24. Installing the Thread Stand 1. Assemble the thread stand unit and insert it in the hole in the machine table. 2. Tighten locknut (1) to fix the thread stand. 3. For ceiling wiring pass the power cord through spool rest rod (2). Fig. -
Page 22: Notes
ANITA © 5) NOTES Serie GF-105... -
Page 23: Spare Parts List
ANITA © 6. SPARE PARTS LIST Serie GF-105...