Advertisement
ENGLISH
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
c. Disconnect the plug from the power source and/or
the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool
accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power.tool or these instructions to operate the power
tool. Power tools are dangerous in the hands of
untrained users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f.
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will make sure that the safety of the power tool is
maintained.
ADDITIONAL SAFETY INSTRUCTIONS FOR
AUSTRALIA AND NEW ZEALAND
a. Young children and the infirm.This appliance is not intended
for use by young children or infirm persons without
supervision. Young children should be supervised to ensure
they do not play with this appliance.
b. Replacement of the supply cord. If the supply cord is
damaged, it must be replaced by the manufacturer or an
authorised Porter-Cable Service Centre in order to avoid a
hazard.
4
ADDITIONAL SAFETY INSTRUCTION FOR
DRILLS
Wear ear protectors when impact drilling. Exposure
•
to noise can cause hearing loss.
Use auxiliary handle(s), if supplied with the tool.
•
Loss of control can cause personal injury.
•
Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live" and
could give the operator an electric shock.
ELECTRICAL SAFETY
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
This appliance is not intended for use by young or infirm
persons without supervision. Children must be supervised
to ensure they do not play with the appliance.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Porter-Cable Service Centre
in order to avoid a hazard.
FEATURES
This tool includes some or all of the following features.
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Chuck
5. Drilling mode selector
ASSEMBLY
Warning! Before assembly, make sure that the tool
is switched off and unplugged.
Keyed chuck (fig. B)
•
Open the chuck by turning the sleeve counterclock-
wise.
•
Insert the bit shaft (6) into the chuck.
•
Insert the chuck key (7) into each hole (8) in the side
ofthe chuck and turn clockwise until tight.
Removing and refitting the chuck (fig. C)
•
Open the chuck as far as possible.
•
Remove the chuck retaining screw, located in the
chuck,by turning it clockwise using a screwdriver.
•
Tighten an Allen key into the chuck and strike it with a
hammer as shown.Remove the Allen key.
•
Remove the chuck by turning it counter clockwise.
•
To refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Advertisement
