Page 1
90538205 PC700D & PC650HD 7/2/08 1/2 inch (13mm) Drill & Hammer Drill Marteau perforateur et perceuse de 1/2 po (13 mm) Taladro y taladro percutor de 13 mm (1/2 pulgadas) Instruction manual Manuel d'instructions Manual de'instrucciones www.portercable.com INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE...
90538205 PC700D & PC650HD 7/2/08 General Safety Rules Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term “power tool” in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
90538205 PC700D & PC650HD 7/2/08 4) Power tool use and care a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
90538205 PC700D & PC650HD 7/2/08 with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. • Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water.
90538205 PC700D & PC650HD 7/2/08 • When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The following table shows the correct size to use depending on cord length and nameplate ampere rating.
Page 6
7/2/08 SAFETY WARNINGS AND INSTRUCTIONS: DRILLS 1. Hold drill firmly with one hand on the grip and the other hand on the side handle as shown in figure C. 2. When attaching accessories in the drill chuck, tighten with all three holes to prevent slippage.
• Rotate the side handle into the desired position. • Insert the depth stop (8) into the mounting hole as shown. (for PC650HD only) • Set the drilling depth as described under “Setting the Drilling Depth”. (for PC650HD only) •...
• Set the depth stop (8) to the desired position. The maximum drilling depth is equal to the distance between the tip of the drill bit and the front end of the depth stop. • Tighten the side handle by turning the grip clockwise.
We cannot guarantee repairs made or attempted by others. You can also write to us for information at PORTER-CABLE, 4825 Highway 45 North, Jackson, Tennessee 38305, (888) 848-5175 - Attention: Product Service. Be sure to include all of the information shown on the nameplate of your tool (model number, type, serial number, etc.).
“four point star” design; and three contrasting/outlined longitudinal stripes. The following are also trademarks for one or more Porter-Cable and Delta products: 2 BY 4®, 890™, Air America®, AIRBOSS™, Auto-Set®, B.O.S.S.®, Bammer®, Biesemeyer®, Builders Saw®, Charge Air®, Charge Air Pro®, CONTRACTOR SUPERDUTY®, Contractor's Saw®,...
Page 11
90538205 PC700D & PC650HD 7/2/08 Marteau perforateur et perceuse de 1/2 po (13 mm) Manuel d'instructions www.portercable.com 12:29 PM Page 11 N° DE CATALOGUE PC700D PC650HD...
Page 12
90538205 PC700D & PC650HD 7/2/08 Avertissements de sécurité généraux pour les outils électriques Lire tous les avertissements de sécurité et toutes les directives. Le non-respect des avertissements et des directives pourrait se solder par un choc électrique, un incendie et/ou une blessure grave.
Page 13
90538205 PC700D & PC650HD 7/2/08 d) Retirer toute clé de réglage ou clé standard avant de démarrer l’outil. Une clé standard ou une clé de réglage attachée à une partie pivotante peut causer des blessures. e) Ne pas trop tendre les bras. Conserver son équilibre en tout temps. Cela permet de mieux maîtriser l’outil électrique dans les situations imprévues.
90538205 PC700D & PC650HD 7/2/08 CONSIGNES DE SÉCURITÉ PARTICULIÈRES • Porter des protecteurs auditifs si une perceuse à percussion est utilisée. Une exposition au bruit peut entraîner une perte auditive. • Utiliser les poignées auxiliaires fournies avec l’outil. Une perte de maîtrise de l’outil peut entraîner des blessures corporelles.
Page 15
90538205 PC700D & PC650HD 7/2/08 LIGNES DIRECTRICES EN MATIÈRE DE SÉCURITÉ - DÉFINITIONS Il est important que vous lisiez et compreniez ce mode d’emploi. Les informations qu’il contient concernent VOTRE SÉCURITÉ et visent à ÉVITER TOUT PROBLÈME. Les symboles ci-dessous servent à vous aider à reconnaître cette information.
Page 16
(MODÈLE PC650HD SEULEMENT) • Régler la butée de profondeur comme décrit sous la rubrique « Réglage de la profondeur de perçage ». (MODÈLE PC650HD SEULEMENT) • Serrer la poignée latérale en la tournant en sens horaire. INSÉRER UNE MÈCHE OU UN AUTRE ACCESSOIRE (FIG. E) ne pas essayer de resserrer les mèches (ou tout autre...
à double marche (4) à la position 2 en alignant le nombre avec le repère sur le boîtier (2e marche). RÉGLAGE DE LA PROFONDEUR DE PERÇAGE (MODÈLE PC650HD) (FIG. D) • Donner du mou à la poignée latérale (9) en la tournant en sens antihoraire.
Page 18
90538205 PC700D & PC650HD 7/2/08 Verrouiller la perceuse en position de MARCHE uniquement si elle est fixe sur un socle de perceuse à colonne ou un autre dispositif de fixation. NE JAMAIS LA VERROUILLER LORS D’UNE UTILISATION MANUELLE ! Ne jamais débrancher l’outil avec le dispositif de verrouillage engagé.
Web www.portercable.com. Il est également possible de commander des pièces au centre de réparation de l’usine Porter-Cable et au centre de réparation sous garantie autorisé Porter-Cable le plus près. Ou composer le 1-888-848-5175 pour le service à la clientèle.
Les éléments ci-dessous sont des marques de commerce des outils et des accessoires de PORTER-CABLE : un agencement de couleurs grise et noire; un motif d’ « étoile à quatre pointes » et trois bandes longitudinales contrastantes/à contours. Les marques suivantes sont également des marques de commerce se rapportant à...
Page 21
90538205 PC700D & PC650HD 7/2/08 12:29 PM Page 21 Driver Series®, SUPERDUTY®, T4 & DESIGN®, THE AMERICAN WOODSHOP®, THE PROFESSIONAL EDGE®, Thin-Line®, Tiger Saw®, TIGERCLAW®, TIGERCLAW AND DESIGN®, Torq-Buster®, TRU-MATCH®, T-Square®, Twinlaser®, Unifence®, Uniguard®, UNIRIP®, UNISAW®, UNITED STATES SAW®, Veri-Set®, Versa-Feeder®, VIPER®, VT™, VT RAZOR™, Water Driver®, WATER VROOM®, Waveform®, Whisper Series®, X5®, YOUR...
Page 22
90538205 PC700D & PC650HD 7/2/08 Taladro y taladro percutor de 13 mm (1/2 pulgadas) Manual de'instrucciones www.portercable.com INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. 12:29 PM Page 22 CATÁLOGO N°...
Page 23
90538205 PC700D & PC650HD 7/2/08 Advertencias generales de seguridad para herramientas eléctricas ADVERTENCIA Lea todas las advertencias de seguridad e instrucciones El incumplimiento de las advertencias e instrucciones puede provocar descargas eléctricas, incendios o lesiones graves. Conserve todas las advertencias e instrucciones para futuras consultas.
Page 24
90538205 PC700D & PC650HD 7/2/08 e) No se estire. Conserve el equilibrio adecuado y manténgase parado correctamente en todo momento. Esto permite un mejor control de la herramienta eléctrica en situaciones inesperadas. f) Use la vestimenta adecuada. No use ropas holgadas ni joyas. Mantenga el cabello, la ropa y los guantes alejados de las piezas en movimiento.
90538205 PC700D & PC650HD 7/2/08 NORMAS DE SEGURIDAD ESPECÍFICAS • Utilice protectores auditivos con los taladros de impacto. La exposición al ruido puede ocasionar la pérdida de la audición. • Use los mangos auxiliares que se suministran con la herramienta. La pérdida del control podría ocasionar lesiones personales.
Page 26
90538205 PC700D & PC650HD 7/2/08 PRECAUCIÓN indica una situación de peligro potencial que, si no se evita, provocará lesiones leves o moderadas. PRECAUCIÓN utilizado sin el símbolo de alerta de seguridad indica una situación de peligro potencial que, si no se evita, puede provocar daños en la propiedad.
90538205 PC700D & PC650HD 7/2/08 ADVERTENCIA El taladro se puede atascar (si se sobrecarga o se usa inadecuadamente) y provocar una torsión. Siempre espere el atascamiento. Sujete el taladro firmemente con ambas manos para controlar la torsión y evitar la pérdida de control que podría ocasionar lesiones personales.
(4) a la posición 2 mediante la alineación del número con la marca en la cubierta (segundo engranaje). AJUSTE DE LA PROFUNDIDAD DE PERFORACIÓN (PC650HD) (FIG. D) • Gire la agarradera en sentido contrario a las agujas del reloj y afloje el mango lateral (9).
Page 29
90538205 PC700D & PC650HD 7/2/08 TALADRADO • Cuando acople o retire accesorios del taladro, desenchúfelo siempre. Es importante que cuando acople accesorios al portabrocas del taladro asegure con firmeza el portabrocas mediante los tres orificios para evitar el deslizamiento de la broca.
90538205 PC700D & PC650HD 7/2/08 DETECCIÓN DE PROBLEMAS Problema Causa posible •La unidad no enciende. • Cable desenchufado. • Fusible quemado. • El interruptor automático está activado. • Interruptor o cable dañado. • Haga reparar el cable o el Para conocer la ubicación del centro de mantenimiento más cercano a fin de recibir ayuda con su producto, visite nuestro sitio Web www.portercable.com o llame a la...
90538205 PC700D & PC650HD 7/2/08 ACCESORIOS ADVERTENCIA Debido a que no se han probado con este producto otros accesorios que no sean los que ofrece Porter Cable, el uso de dichos accesorios con esta herramienta podría ser peligroso. Para reducir el riesgo de lesiones, con este producto deben usarse sólo los accesorios Porter Cable recomendados.
90538205 PC700D & PC650HD 7/2/08 TIGERCLAW®, TIGERCLAW AND DESIGN®, Torq-Buster®, TRU-MATCH®, T-Square®, Twinlaser®, Unifence®, Uniguard®, UNIRIP®, UNISAW®, UNITED STATES SAW®, Veri-Set®, Versa-Feeder®, VIPER®, VT™, VT RAZOR™, Water Driver®, WATER VROOM®, Waveform®, Whisper Series®, X5®, YOUR ACHIEVEMENT. OUR TOOLS.® Las marcas comerciales con el símbolo ® están registradas en la Oficina de patentes y marcas comerciales de Estados Unidos (United States Patent and Trademark Office), y también pueden...
Need help?
Do you have a question about the PC650HD and is the answer not in the manual?
Questions and answers