Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Cuppone Pizzaform
Summary of Contents for Cuppone Pizzaform
- Page 1 Pizzaform User manual...
-
Page 3: Table Of Contents
Technical service..................3 use and maintenance. Safety instructions ............4 In this manual you will find all the information on the PIZZAFORM Do not hesitate to contact him in case of doubt. series of electronically controlled pizza hot-formers. Risk analysis ....................5 Symbols used in the manual ..............5... -
Page 4: Safety Instructions
Safety instructions • Read this guide carefully before using and main- ple and animals and might irreparably damage ized by the Manufacturer. Ask for original spare taining the appliance, and keep it with care in an the equipment. Improper use of the equipment parts or the Warranty will be forfeited. -
Page 5: Risk Analysis
Partial reproduction prohibited without the Manufacturer’s consent. The measurements provided are indicative and not binding. The original language is Italian: the Manufacturer is not responsible for any translation/interpretation or print errors. Ed. 0719 - 70702572 REV00 Pizzaform - Use and maintenance... -
Page 6: Symbols Applied To The Machine
Safety instructions Symbols applied to the machine Equipotential Risk of crushing fingers. Risk of electrocution Risk due to scalding surface Pay attention to gears • ATTENTION: Read the • ATTENTION: When the plate stops, attached manual care- switch the machine off and on again. fully before using the Do not force it. -
Page 7: Basic Notions
Ed. 0719 - 70702572 REV00 Pizzaform - Use and maintenance... -
Page 8: Some Piece Of Advice
Basic notions Some piece of advice... 150/160°C • Set the temperature of the plates at and contact seconds. These values satisfy the process- time equal to ing of most doughs but may vary depending on the type of dough used by the operator, its leavening degree and its temperature. -
Page 9: Use
Act on the control panel using only your dry and clean the thickness of the dough disk; by moving the lever in a fingers counter-clockwise direction the thickness decreases, mov- ing it in a clockwise direction increases the thickness. Ed. 0719 - 70702572 REV00 Pizzaform - Use and maintenance... -
Page 10: Switching On
Switching on Fig.4. ON/OFF key (11). Switch the machine ON pressing the After a few seconds, the displays will show the current (display (1) temperatures of the plates shows the temperature display (3) of the upper plate, that of the lower plate). It is then necessary to set 3 parameters: temperatures •... -
Page 11: Adjusting The Distance Between The Plates
Make sure there are no foreign objects on the lower plate protection grille (14). and lower the The lower plate will automatically get near the upper plate to flatten the dough ball. Ed. 0719 - 70702572 REV00 Pizzaform - Use and maintenance... -
Page 12: Switching Off
Fig.11. Fig.11. After the set contact time, the lower plate will go back to its starting position. protection grille (14) Lift the and remove the dough being careful not to burn yourself on the warm disk, plates (use personal protection equipment such as heat insulating gloves). -
Page 13: How To Solve Some Processing Problems
• Let the dough leaven longer placing it in a warm place Bubbles appear on the surface of the • The dough ball has not leavened enough. pizza during cooking • Pierce the dough disk with a pastry cutter before filling Ed. 0719 - 70702572 REV00 Pizzaform - Use and maintenance... -
Page 14: Automatic Switching On Of The Appliance
Special functions: automatic Special functions: strike counter switching on of the appliance With the appliance display switched off (plug in, emergency STOP button unlocked, ON/OFF key not ON), pressing the The board is equipped with a special function for the automatic “+”... -
Page 15: Maintenance And Cleaning
(polycarbonate). It is best to have an authorized service centre perform maintenance and inspection on the appliance at least once a year to ensure top working and safety conditions. Ed. 0719 - 70702572 REV00 Pizzaform - Use and maintenance... -
Page 16: Maintenance And Cleaning
Maintenance and cleaning Downtime for prolonged periods Disposal at end of life Information on disposal in European Union countries The EU Directives on WEEE equipment has been adopted When the product is not in operation, disconnect it from the To avoid any unauthorised use and associated risks, be- in different ways by different countries, therefore in order to mains. -
Page 17: Warranty
The warranty is not valid for damages caused by: • chemical and atmospheric agents, fires, faults in the room Cuppone F.lli s.r.l. ’ s liability is limited to the supply of the electrical system, product misuse, lack of maintenance, prod-... -
Page 18: Something Is Not Working
• Call an authorized Service Centre or contact the Dealer/Man- ufacturer directly, stating the product data. While waiting for technical assistance, disconnect the product from the power supply. CUPPONE 1963 Cuppone F.lli S.r.l. Via Sile, 36 31057 Silea (TV) - ITALY T +39 0422 361143 F +39 0422 360993... -
Page 19: Diagnostics
“tUP” parameter. NOTE: “Err” the machine switches off. To restore the functions, switch the machine on and off again. If the problem persists, contact the service centre. Fig.16. Ed. 0719 - 70702572 REV00 Pizzaform - Use and maintenance... - Page 20 CUPPONE 1963 Cuppone F.lli S.r.l. Via Sile, 36 31057 Silea (TV) - ITALY T +39 0422 361143 F +39 0422 360993 info@cuppone.com - www.cuppone.com...
Need help?
Do you have a question about the Pizzaform and is the answer not in the manual?
Questions and answers