Related Manuals for norbar TruCheck 0.1
Summary of Contents for norbar TruCheck 0.1
- Page 1 OPERATOR’S MANUAL TRUCHECK & TRUCHECK PLUS Part Number 34384 | Issue 1 | Original Instructions (English)
-
Page 3: Table Of Contents
CONTENTS PAGE Installation (All 3, 10 & 25 Nꞏm models) Operation (43250, 43251 & 43252) Operation (43253, 43254 & 43255) Technical Specification (All 3, 10 and 25 Nꞏm models) Calibration Repair Cleaning Warning Disposal Installation (All 350, 1000, 2000 Nꞏm, and 250 & 750 lbfꞏft models) Operation (43222, 43231 &... -
Page 4: Installation (All 3, 10 & 25 NꞏM Models)
TruCheck Plus 0.1 – 3.0 N∙m 43251 TruCheck Plus 1 - 10 N∙m 43252 TruCheck Plus 1 – 25 N∙m 43253 TruCheck 0.1 – 3.0 N∙m 43254 TruCheck 1 - 10 N∙m 43255 TruCheck 1 – 25 N∙m INSTALLATION 1. Identify a suitable surface and position to mount the instrument. -
Page 5: Operation (43250, 43251 & 43252)
OPERATION (43250, 43251 & 43252) MODE Button 1. Press MODE button briefly to display current mode of operation. 2. Press and hold MODE button to change mode of operation. Release button at required mode to accept. 3. Modes of operation. ... -
Page 6: Operation (43253, 43254 & 43255)
OPERATION (43253, 43254 & 43255) 1. Place screwdriver / wrench in the instrument and operate in the desired direction. Remove screwdriver / wrench and zero the display (if required) by pressing the red button located on the side of the instrument. 2. -
Page 7: Repair
REPAIR Repair should be carried out by the Supplier or by the Supplier approved agent, where all the facilities to ensure the instrument is functioning at maximum accuracy are available. There are no parts for user repair inside the case. CLEANING Do not use abrasives or solvent based cleaners. -
Page 8: Installation (All 350, 1000, 2000 NꞏM, And 250 & 750 LbfꞏFt Models)
Part Number Description 43221 TruCheck 10 – 350 N∙m 43222 TruCheck Plus 10 – 350 N∙m 43226 TruCheck 10 – 250 lbf∙ft 43227 TruCheck 10 – 250 lbf∙ft F/W RS232 43230 TruCheck 100 – 1000 N∙m 43231 TruCheck Plus 100 – 1000 N∙m 43237 TruCheck 75 –... -
Page 9: Operation (43222, 43231 & 43245)
OPERATION (43222, 43231 & 43245) MODE Button 1. Press MODE button briefly to display current mode of operation. 2. Press and hold MODE button to change mode of operation. Release button at required mode to accept. 3. Modes of operation. ... -
Page 10: Operation (43227 & 43238)
OPERATION (43221, 43226, 43230, 43237 & 43244) 1. Place wrench in the instrument and operate wrench in the desired direction. Remove wrench and zero the display (if required) by pressing the red button located on the side of the instrument. 2. -
Page 11: Calibration
Environmental conditions: a) Indoor use. IP 40. b) Altitude up to 2000 m. c) Temperature 5°C to 40°C. d) Maximum relative humidity 80% for temperatures up to 31°C decreasing linearly to 50% relative humidity at 40°C. e) Mains supply voltage fluctuations up to ±10% of nominal voltage. TRANSIENT OVERVOLTAGES up to the levels of OVERVOLTAGE CATEGORY II Due to continuous improvement all specifications are subject to change without prior notice. - Page 12 This page left intentionally blank.
- Page 14 SINGAPORE 128383 Tel + 44 (0)1295 270333 Tel + 65 6841 1371 Email enquiry@norbar.com Email enquires@norbar.sg NORBAR TORQUE TOOLS INDIA PVT. LTD NORBAR TORQUE TOOLS PTY LTD Plot No A-168, Khairne Industrial Area, 45–47 Raglan Avenue, Edwardstown, Thane Belapur Road, Mahape, SA 5039 Navi Mumbai –...