Advertisement
Settings in accordance with security
grade 2
If security grade 2 is required, it can be configured by selecting
EN 50131, grade. 2. from System profiles located in the Parameters
tab in the F-Link software. The device will be configured according
to the selected standard.
Siren indication priority
Fire alarm indication has the highest priority followed by IW and EW
alarm.
A lower indication priority belongs to interaction with the system
(setting/unsetting...) followed by indication upon activation of PG
outputs (PG1 has a higher priority than PG2 etc.). Indication with
a higher priority always terminates indication with a lower priority.
Priority levels of acoustic indication in descending order: Fire alarm,
IW/EW alarm, warning indication, unsetting the system with an active
alarm memory indication, Setting/Unsetting, Entrance/Exit delay, alarm
memory indication, PG output indication and finally, the siren flashes
an LED light when the status of the tamper sensor changes.
Battery replacement
A battery is included, however it is not factory-fitted in the siren
therefore it needs to be inserted into the device. The battery recharges
in a standard way (see Technical specifications). When replacement
is necessary, it is possible to order the BAT-3V2-CR2 replacement
battery. Connect it to the connector (see figure 1, point 2). The siren
automatically detects whether the battery is connected and performs
diagnostics. The measured values are then displayed in the F-Link
software. The siren monitors its own battery status and informs
a user (alternatively the service technician) when the battery is close
to being depleted. The device continues in its function however
it is recommended to replace the battery within 2 weeks. Use the BAT-
3V2-CR2 type of battery specifically.
The battery should be replaced by a service technician while
the control panel is in Service mode. Do not discard the battery
in the trash; dispose of it at a waste collection point.
Siren FW update
The siren supports wireless FW updates performed by the F-Link
software while the control panel is in Service mode.
1. Click on the Control panel menu Firmware update. JA-150A
will appear in a dialog window. If F-Link contains newer firmware,
it will be selected automatically.
2. Confirm the update of the selected devices by clicking on the OK
button.
3. When the FW update has finished, check the siren's internal
settings in the Devices window Internal settings.
4. Test whether the siren functions correctly.
The JA-150A II Internal wireless siren
The JA-150A II Internal wireless siren
Dimensions
Technical specifications
Power supply/wattage
110 - 230 V/50 -60 Hz, 0.6 W, protection class II
Connecting cables - maximum diameter
Backup / recharge time
Battery type
Battery / lifetime
/ minimum voltage when loaded
/ maximum voltage when unloaded
Communication band
Communication range
Classification
- According to
- Alarm sound level
- Back up power supply
- Operational environment
- Operating temperature range
- Average operational humidity
- Certification body
IP rating
Dimensions
Also complies with
EN 55032:2015, EN 62368-1, EN 50131-5-3,
Can be operated according to
JABLOTRON ALARMS a.s. hereby declares that the JA-150A II
is in a compliance with the relevant European Union
harmonisation
2014/35/EU, 2014/30/EU, 2011/65/EU.
The original of the conformity assessment can be found
at www.jablotron.com - Downloads Section.
Note: Although this product does not contain any harmful
materials we suggest you return the product to the dealer
or directly to the producer after use.
2 / 2
min. 24 h/max 72 h
BAT-3V2-CR2/LiFePo4
Warning: Battery is not installed
3.2 V; 470 mAh/3 years
868.1 MHz, JABLOTRON protocol
approx. 300 m (open area)
security grade 2/environmental class II
EN 50131-1
100 dB/1 m (±5 dB/1 m)
type W/24h back up
indoor general
-10 °C to +40 °C
75 % RH, non-condensing
Trezor Test s.r.o. (no. 3025)
IP43 according to EN 50131-1
80 x 80 x 35 mm
ETSI EN 300 220, EN 50130-4+A1:2014,
EN 50581:2012, EN 50131-4, EN 50131-6
ERC REC 70-03
legislation:
Directives
No:
MLP20100
2
1.5 mm
3.0 V
3.6 V
2014/53/EU,
Advertisement
