Fluke 5730A Calibration Manual page 33

AC Current Secondary Performance Specifications and Operating Characteristics
Stability ±1 °C
24 Hours
Frequency
Range
(Hz)
±(ppm output +
10 - 20
20 - 40
220 μA
40 - 1 k
1 k - 5 k
5 k - 10 k 400 + 100
10 - 20
20 - 40
2.2 mA 40 - 1 k
1 k - 5 k
5 k - 10 k 400 + 100
10 - 20
20 - 40
22 mA 40 - 1 k
1 k - 5 k
5 k - 10 k 400 + 1000
±(ppm output +
Hz
10 - 20 150 + 0.5
20 - 40
220 mA 40 - 1 k
1 k - 5 k
5 k - 10 k
20 - 1 k
2.2 A 1 k - 5 k
5 k - 10 k
40 - 1 k
11 A 1 k - 5 k 100 + 150
5 k - 10 k 200 + 300
Notes:
Maximum output from 5730A terminals is 2.2 A. Specifications for 220 μA and 2.2 mA ranges are increased by a factor of 1.3, plus
2 μA when supplied through 5725A terminals. Specifications are otherwise identical for all output locations.
1. Stability specifications are included in the Absolute values for the primary specifications.
Temperature coefficient is an adder to specifications that does not apply unless operating more than ±5 °C from calibration
2.
temperature.
3. For larger resistive loads multiply accuracy specifications by: (
4. 1.5 V compliance limit above 1 A. 5725A Amplifier may be used in range-lock mode down to 1 A.
5. For resistive loads within rated compliance voltage limits.
Minimum Output .................................................... 9
Inductive Load Limits ........................................... 400
Power Factors ........................................................ 5730A, 0.9 to 1; 5725A, 0.1 to 1. Subject to compliance voltage
Frequency
Range (Hz) .......................................................... 10.000 - 11.999, 12.00 - 119.99, 120.0 - 1199.9, 1.200 k - 10.000 k
Specification .................................................. ±0.01 % of output
Resolution ..................................................... 11,999 counts
Temperature
Coefficient
[1]
10 - 40 °C
±(ppm output + nA)/ °C
nA)
150 + 5 50 + 5
80 + 5 20 + 5
30 + 3 4 + 0.5
50 + 20 10 + 1
20 + 100
150 + 5 50 + 5
80 + 5 20 + 4
30 + 3 4 + 1
50 + 20 10 + 100
50 + 400
150 + 50 50 + 10
80 + 50 20 + 10
30 + 30 4 + 10
50 + 500 10 + 500
50 + 1000
±(ppm output + μA)/°C
μA)
50 + 0.05
80 + 0.5 20 + 0.05
30 + 0.3 4 + 0.1
50 + 3 10 + 2
400 + 5 50 + 5
50 + 5 4 + 1
80 + 20 10 + 5
800 + 50 50 + 10
5725A Amplifier:
75 + 100 20 + 75
40 + 75
100 + 75
μA for 220
5725A.
(5730A, or 5725A). 20
μH
limits.
[2]
Compliance
0 - 10 °C and
Limits
40 - 50 °C
(V rms)
Specification
50 + 5
20 + 5
10 + 0.5 7
20 + 1
20 + 100
50 + 5
20 + 4
10 + 2 7
20 + 100
50 + 400
50 + 10
20 + 10
10 + 20 7
20 + 400
50 + 1000
50 + 0.05
20 + 0.05
10 + 0.1 7
20 + 2
50 + 5
10 + 1
[4]
20 + 5 1.4
50 + 10
30 + 75
50 + 75 3
100 + 75
actual load
maximum load for published specificat
μA range, 10 % on all other ranges. 1 A minimum for
for 5730A output >1 A.
μH
Multifunction Calibrator
Electrical Specifications
Noise and
Maximum
Distortion
Resistive
(Bandwidth
Load
10 Hz - 50 kHz
For
<0.5V Burden)
Published
±(% output + μA)
[3]
(Ω)
0.05 + 0.1
0.05 + 0.1
2 k 0.05 + 0.1
0.25 + 0.5
00.5 + 1
0.05 + 0.1
0.05 + 0.1
800 0.05 + 0.1
0.25 + 0.5
00.5 + 1
0.05 + 0.1
0.05 + 0.1
80 0.05 + 0.1
0.25 + 0.5
00.5 + 1
0.05 + 10
0.05 + 10
8 0.05 + 10
0.25 + 50
00.5 + 100
0.5 + 100
0.8 0.3 + 500
1 + 1 mA
±(% output)
[5]
0.05
[5]
3 0.12
[5]
0.5
2
)
ion
23