Advertisement
Quick Links
Advertisement
Related Manuals for dams COU800OL
Summary of Contents for dams COU800OL
- Page 1 22.01.2017 COU800OL Connex 800mm Outer Leg Frame...
- Page 2 1,2,3...
- Page 3 Please check that you have all the Components! 800mm Outer Leg Frame Fixed Length Beam 1200 / 1400 / 1600mm Desk Top 1200 / 1400 / 1600mm Please check that you have all the Fittings! (Fittings supplied with leg frames) 800mm Outer Leg Frame M6x60mm Connect Bolt M6 Nylon Insert...
- Page 4 Step 1 Attach the first beam to the end leg using the M6 bolts provided. Loosely thread the bolts into the face of the leg before threading the bolts to the underside of the leg. Once all bolts are threaded you can fully tighten them using the 4mm Allen Key.
- Page 5 If horizontal cable management is being added please refer to the single cable tray assembly instruction before proceeding with the next steps. This will make the installation process much easier then trying to install the cable trays once the desktops are attached. Step 3 Insert the nylon inserts into the pre drilled holes on the underside of the desktop.
- Page 6 Step 4 Position the first desktop on the frame aligning the nylon inserts with the slotted holes . Step 5 Attach the desktop using the 60mm connect bolts as shown. Loosely thread all the bolts to ensure that no bolts become cross threaded before fully tightening.
- Page 7 22.01.2017 COU800IL Connex 800mm Intermediate Leg Frame This assembly instruction is to be used in conjunction with COU800OL instruction.
- Page 8 1,2,3...
- Page 9 Please check that you have all the Components! 800mm Intermediate Leg Frame Fixed Length Beam 1200 / 1400 / 1600mm Desk Top 1200 / 1400 / 1600mm Please check that you have all the Fittings! (Fittings supplied with leg frames) 800mm Intermediate Leg Frame M6x60mm Connect Bolt M6 Nylon Insert...
- Page 10 This assembly instruction continues from the steps you have so far completed from the ED800OL instruction sheet. Step 3 Attach the intermediate leg frame using the same method as before. Attach the beams to the leg using the M6 bolts provided. Loosely thread the bolts into the face of the leg before threading the bolts to the...
- Page 11 Step 4 Attach the second beam to the intermediate leg using the M6 bolts provided. Loosely thread the bolts into the face of the leg before threading the bolts to the underside of the leg. Once all bolts are threaded you can fully tighten them using the 4mm Allen Key.
- Page 12 Step 5 Attach the remaining outer leg frame using the same method as before. Attach the beams to the end leg using the M6 bolts provided. Loosely thread the bolts into the face of the leg before threading the bolts to the underside of the leg.
- Page 13 Step 6 Insert the nylon inserts into the pre drilled holes on the underside of the desktop. The illustration below shows which pre drilled holes should be used. Repeat this step for all desktops. Step 7 Position the first desktop on the frame aligning the nylon inserts with the slotted holes .
- Page 14 Step 9 Attach the desktop using the 60mm connect bolts as shown. Loosely thread all the bolts to ensure that no bolts become cross threaded before fully tightening. Repeat this step for all remaining desktops. This assembly instruction illustrates how to assemble a 2 person configuration. For larger configurations repeat steps 3 - 9 for each add on bay you would like to add.
Need help?
Do you have a question about the COU800OL and is the answer not in the manual?
Questions and answers