Related Manuals for dams FZ1600OL
Summary of Contents for dams FZ1600OL
- Page 1 08.03.2018 FZ1600OL Fuze Outer Leg BEAM BEAM FIXING FIXING POINTS POINTS DESKTOP DESKTOP SCREEN FIXING FIXING FIXING POINTS POINTS POINTS Used to build Fuze Back to Back Desk Fuze Boardroom Table...
- Page 2 1,2,3...
- Page 3 1200mm = EDBT1216T 1400mm = ED148T 1600mm = EDBT1616T 1600mm = ED168T 2 x OUTER LEG FRAMES ( FZ1600OL ) FITTINGS SUPPLIED WITH EACH LEG 2 x OUTER LEG PANELS ( FZW-1 ) M8 x 50mm Bolt Leg Spacer Block...
- Page 4 Back to Back Desk Assembly Step 1 Insert the beam infill blocks into both ends of the beam. Step 2 Push the beams onto the 1st leg frame lining up the beam holes with the M6 threaded holes on the leg. Ensure the screen fixing points on the outer leg and cut out...
- Page 5 Step 4 Push the beams onto the remaining leg frame lining up the beam holes with the M6 threaded holes on the leg. Please Note If you have purchased a larger configuration of desk than the one shown please refer to the FZ1600IL instruction before proceeding with step 4...
- Page 6 Step 6 Ensure that the Position the Spacer spacer blocks Blocks over the holes are placed onto in the leg frames. the frame with the recessed nut holes facing upwards. Leg Spacer Block Please Note For ease of assembly Screen Brackets and Horizontal Cable Trays should be fitted before you proceed to Step 7.
- Page 7 Step 7 Place the desktop onto the assembled framework ensuring that the edges of the desktop finish parallel with the end of the leg frames. The framework may be slightly out of square, if this happens loosen the fixing bolts in the beams and align correctly before re tightening the bolts.
- Page 8 Step 8 Attach one side of the desktops to the frame using the M6 x 60mm Connect Bolts. Ensure that the bolt passes through both the leg frame and Spacer Block. M6 x 60mm Connect Bolt Step 9 Attach the remaining side of the desktops to the frame using the M6 x 60mm Connect Bolts.
- Page 9 08.03.2018 FZ1600IL Fuze Inner Leg BEAM BEAM FIXING FIXING POINTS POINTS DESKTOP DESKTOP SCREEN FIXING FIXING FIXING POINTS POINTS POINTS Used to build Fuze Back to Back Desk Fuze Boardroom Table...
- Page 10 Please check that you have all the components DESK TOP TABLE TOP (Number of tops is dependant on configuration ) (Number of tops is dependant on configuration ) 800mm Deep Tops 1600mm Deep Tops 1200mm = ED128T 1200mm = EDBT1216T 1400mm = ED148T 1600mm = EDBT1616T 1600mm = ED168T...
- Page 11 Back to Back Desk Assembly Please Note This assembly instruction follows on from step 3 on the outer leg assembly instruction FZ1600OL Step 4 Push the beam onto the Inner leg frame lining up only the outer beam holes with the...
- Page 12 Step 5 Once the holes are aligned fix the beam in place using the M6 x 25mm Connect Bolts. M6 x 25mm Connect Bolt Step 6 Push the next set of beams onto the inner leg frame lining up only the outer beam holes with the M6 threaded holes nearest the edge on the leg.
- Page 13 Step 7 Once the holes are aligned fix the beam in place using the M6 x 25mm Connect Bolts. M6 x 25mm Connect Bolt Step 8 Push the beams onto the remaining outer leg frame lining up the beam holes with the M6 threaded holes on the leg.
- Page 14 Step 9 Once the holes are aligned fix the beams in place using the M6 x 25mm Connect Bolts. Please Note If you have purchased a sliding top system please refer to the sliding top M6 x 25mm Connect Bolt bracket assembly instruction from this point onwards.
- Page 15 Step 11 Place the desktop onto the assembled framework ensuring that the edges of the desktop finish parallel with the end of the leg frames. The framework may be slightly out of square, if this happens loosen the fixing bolts in the beams and align correctly before re tightening the bolts.
- Page 16 Step 12 Attach the desktops to the frame using the M6 x 60mm Connect Bolts. Ensure that the bolt passes through both the leg frame and Spacer Block. M6 x 60mm Connect Bolt...
Need help?
Do you have a question about the FZ1600OL and is the answer not in the manual?
Questions and answers