Function-Keys - Gaspardo PRECIMAT Use And Assembly Instructions / Spare Parts

ENGLISH
3.4.4.2 Switch-on of the monitoring of aggregates
After aggregates have been switched off from the outer side, it is
possible to switch them on again from the inner side in the same
direction:
The actual switch-on is done with "+" key.
If the drive of the aggregates is switched with an electromagnetic
coupling, the aggregate itself will be switched on with switching
on the monitoring.
Example:
The machine has 6 aggregates.
Aggregates 1 and 2 shall be switched-on again.
Procedure:
- Press key
- The display shows: - 2 - 0
- The left minus sign flashes
- Press "+" key (switch-on line 2)
- The display shows : - 1 - 0
- Press "+" key (switch-on line 1)
- The display shows : - 0 - 0
The machine is working again with entire working width.
3.4.4.3 Permanent switch-off of aggregates
In addition to switching-off of aggregates from outside to inside
every single aggregate can be switched off permanently.
For precision seed drills with up to 12 rows the monitoring and
the drive of the aggregates can be switched off permanently. For
switching-off the drive of the aggregates an electromagnetic cou-
pling is necessary.
Procedure:
Enter the number of aggregates as described before and proceed
with the following steps:
- Keep the key pressed for more than 5 seconds until on the
left part of the display a "1" (row 1) appears. The right number
can be changed with the keys "+" and "-".
0 = permanently switched-off
1 = permanently switched-on
- Press "ENTER" key
The LED shines red when row is switched-off and green when row
stays switched-on. On the left part of the display a "2" is shown
and the second LED starts flashing. The status can be changed
again with the keys "+" and "-".
- Repeat this procedure as long as the status of every aggregate
has been set correctly.
- After input of the last aggregate the total number of aggregates
and the total number of active aggregates is shown on the display.
CAUTION
This setting persists even if the machine is lifted at the end of the
field or the computer is switched-off.
It can be suspended by changing the settings or by pressing the
key .
Caution: when pressing the
aggregates –which are permanently switched-off aggregates
are switched on again.
To allow a supervision of the permanent switch-off aggregates,
the switched-off rows are still counted and shown in the working
display (the application rate must be "0"!)
20
USE AND MAINTENANCE
key all switched-off

As a consequence of this, the permanent switched-off row must
be switched-off again to reach the next row when working on a
triangle. When switching on from inside to outside the permanent
switched-off row stays switched-off. The advantage of this proce-
dure is, that row by row can be switched without paying attention
to permanently switched-off rows.
When the permanent aggregate switch-off is selected again, the
last settings are shown again. These can be accepted or changed
to the required settings.
3.4.4.4 "Control all aggregates" key
By pressing "Control all aggregates" key the monitoring of all ag-
gregates is switched-on again. All aggregates that were switched-
off before are switched-on and monitored. This is also valid for
aggregates that have been switched-off permanently.

3.4.5 FUNCTION-KEYS

3.4.5.1 "Hours" key
By pressing "h" the working-time elapsed after activating the start-
function
If the tractor is parked and the computer has no power, the time-
counting is stopped. After switching-on the device the time-counting
is started again. Time-counting can be stopped during work. When
"h" has been pressed time-counting can be stopped by pressing
"h" again. It starts again, when "h" is pressed once more.
3.4.5.2 "Area" key
With this key the area is shown, which has been worked on since
the start function
surement is stopped as soon as the computer does not receive any
wheel impulses. In working mode "0" = Area-counter with sensor
Y (working position), this must be switched on.
3.4.5.3 "Total area" key
With this key the total area of a season can be counted. At the
beginning of the season the counter can be set to 0 by pressing
the keys "Total Area" and "C" simultaneously.
3.4.5.4 "Current area performance" key
Pressing this key the current area performance in ha/h is displayed.
3.4.5.5 "Distance" key
The distance that has been travelled after activating the start-
function
is indicated.
has been activated. The mea-
is displayed.
cod. G19503910