Summary of Contents for Horizon Hobby E-flite BNF UMX HYPER TAXI
Page 1
™ ™ HYPER TAXI Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di Istruzioni...
Page 2
Do not attempt disassembly, use with incompatible components or augment product in any way without the approval of Horizon Hobby, Inc. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.
® ™ ™ The E-fl ite Ultra Micro eXtreme (UMX ) Hyper Taxi BNF is a totally new 3D thrill ride. Combined in one symmetrical design, you get the most fun airplane and helicopter capabilities in one convenient package, including hyper-agility and super-solid stability for vertical takeoff and landings. Although it looks ™...
RC the many complications to assess when trying to pilot skills. achieve smooth fl ight. The Horizon Hobby world- class team of RC pilots developed the AS3X System AS3X will innovate the way you’ll want to fl y now for airplanes based on the successful use of AS3X and in the future.
Charging the Battery ® ™ Your E-fl ite Hyper Taxi comes with a 2-Cell 7.4V 180mAh 20C Li-Po battery and a Celectra ™ 2S 7.4V DC Li-Po Charger which requires a 12V (11V-14V) DC power source. Refer to battery warnings. It is recommended to charge the battery pack while you are inspecting the aircraft.
Battery Warnings The Battery Charger (EFLUC1007) included with the • Always transport or temporarily store the battery Hyper Taxi has been designed to safely charge the in a temperature range of 40–120º F. Do not store Li-Po battery. battery or model in a car or direct sunlight. If stored in a hot car, the battery can be damaged or even catch fi...
Installing the Flight Battery 1. Attach the flight battery to the hook and loop strip under the cockpit. See the Adjusting the Center of Gravity instructions for the battery’s position. 2. Place the aircraft on the ground out of the wind and then connect a fully charged flight battery.
Adjusting Center of Gravity (CG) The CG location is 2mm from the rear edge of the propeller slot. The battery slot is oversized to allow for Center of Gravity adjustment. Start by placing the battery at the front edge of the battery slot with the connector plug facing the front of the aircraft.
Control Direction Test Bind your aircraft and transmitter before performing these tests. Move the controls on the transmitter to make sure the aircraft control surfaces move correctly, freely, and in the proper direction. Tip: Programming for the control surfaces has already been done in the receiver of the Hyper Taxi, so no mixing is required in the transmitter.
Dual Rates and Expos We recommend using a DSM radio capable of dual High Rate Low Rate rates and expo due to the aerobatic capabilities of the Hyper Taxi. The settings shown here are Aileron 100% recommended starting settings. Adjust according to Elevator 100% individual preferences after initial fl...
Flying Tips and Repairs Flying Feel free to experiment with fl ying the Hyper Taxi with the wings at various angles; however, be aware ® ™ We recommend fl ying your E-fl ite Hyper Taxi that the model acts very similarly on its side as it indoors or outside only in 8 mph (13 km) winds does when fl...
Additional Safety Precautions and Warnings As the user of this product, you are solely This model is controlled by a radio signal subject responsible for operating in a manner that does to interference from many sources outside your not endanger yourself and others or result in control.
Service of Power Components CAUTION: DO NOT handle propeller parts while the fl ight battery is connected. Personal injury could result. 1. Gently hold the nose of the aircraft and remove the prop screw (A), propeller (B) and propeller spacer (C) from the motor shaft (D). Hold the motor so it does not turn when the screw is turned.
Troubleshooting Guide AS3X Problem Possible Cause Solution Control surfaces not Control surfaces may not have been me- Center control surfaces mechanically by adjust- at neutral position chanically centered from factory ing the u-bends on control linkages when transmitter Aircraft was moved after the fl ight battery Disconnect and reconnect the fl...
Troubleshooting Guide (Continued) Problem Possible Cause Solution Control surface does Control surface, control horn, linkage or Replace or repair damaged parts and adjust not move servo damage controls Wire damaged or connections loose Do a check of wires and connections, connect or replace as needed Flight battery charge is low Fully recharge or replace fl...
(iii) modifi cation of or to any part of the Product, (iv) representative. You may also find information on our attempted service by anyone other than a Horizon Hobby website at www.horizonhobby.com. authorized service center, or (v) Products not purchased from an authorized Horizon dealer.
Istruzioni per lo smaltimento di RAEE da parte di utenti dell’Unione Europea Questo prodotto non deve essere smaltito insieme ai rifi uti domestici. Al contrario, è responsabilità dell’utente lo smaltimento di tali rifi uti, che devono essere portati in un centro di raccolta designato per il riciclaggio di rifi...
Optional Parts and Accessories – – Optionale Bauteile und Zubehörteile – – Piéces optionnelles et accessoires – – Parti opzionali e accessori – Part # • Nummer Description Beschreibung Description Descrizione Numéro • Codice Charger Plug Adapter: Ladekabel Adapter Prise d’adaptation Adattatore per la EFLA700UM chargeur: EFL...
Need help?
Do you have a question about the E-flite BNF UMX HYPER TAXI and is the answer not in the manual?
Questions and answers