Altronix LINQ8PD Installation And Programming Manual
Network power distribution module
Hide thumbs
Also See for LINQ8PD:
- Installation manual (24 pages) ,
- Installation manual (12 pages) ,
- Installation and programming manual (8 pages)
Advertisement
Quick Links
Network Power Distribution Module
Installation and Programming Manual
LINQ8PD
- Network Power Distribution Module
- Eight (8) Fused Outputs
LINQ8PDCB
- Network Power Distribution Module
- Eight (8) PTC Outputs
DOC#: LINQ8PD Rev. 020916
Available from A1 Security Cameras
www.a1securitycameras.com email: sales@a1securitycameras.com
Please be sure to visit
altronix.com for
latest firmware and
installation instructions
More than just power.™
Advertisement
Related Manuals for Altronix LINQ8PD
Summary of Contents for Altronix LINQ8PD
- Page 1 Installation and Programming Manual LINQ8PD - Network Power Distribution Module - Eight (8) Fused Outputs LINQ8PDCB - Network Power Distribution Module - Eight (8) PTC Outputs More than just power.™ DOC#: LINQ8PD Rev. 020916 Available from A1 Security Cameras www.a1securitycameras.com email: sales@a1securitycameras.com...
-
Page 2: Specifications
Overview: Altronix LINQ8PD(CB) network power distribution module facilitates monitoring, reporting and control of one (1) or two (2) low voltage AC or supervised DC power supply/chargers over the network. Reports diagnostics via Email/SNMP notifications greatly reducing system downtime and eliminating unnecessary service calls. LINQ8PD(CB) retrofits with most currently installed multi-output power supply/chargers. -
Page 3: Led Diagnostics
Downlink Connection to power supply or second LINQ8PD(CB) module. Uplink Connects to next LINQ8PD(CB) upstream from this module. If this is the first LINQ8PD(CB) in the daisy chain this connector is not used. BAT Local LED Indicates battery(ies) thresholds. FACP/AC/BAT LEDs Indicates status of FACP, AC and Battery. -
Page 4: Installation Instructions
[UPLINK] of second LINQ8PD(CB). 3. Power Supply Input Connection: The LINQ8PD(CB) can be connected to two independent AC or DC power supplies that can be routed thru each of the individual outputs. Each output is equipped with an input selection switch which is used to route the desired input to the output. This switch also has a center off position that can be used to turn power off to an output. -
Page 5: Establishing Network Connection
Network Setup - Altronix Dashboard USB Connection The USB connection on the LINQ8PD(CB) is used for Network and Trap Receiver configuration only. When connected to a PC via the USB cable the LINQ8PD(CB) will receive power from the USB port allowing programming of the LINQ8PD(CB) prior to being connected to the power supply. - Page 6 (refer to Installing LINQ8PD Board on pg. 2). e. Connect one end of the network cable to the network jack on the LINQ8PD(CB) and the other to the network connection or the PC to be used for programming. Note: Email notification must be setup via the Browser, Ref to Email Settings in the Browser Setup section of this manual.
- Page 7 After selecting DHCP in the IP Address Method field click [Submit Network Settings] button, a dialog box will display “New network settings will take effect after the server is rebooted” click “OK”. Next click [Reboot Server] button. After rebooting the LINQ8PD(CB) will be set in the DHCP mode. The IP address will be assigned by the router when the LINQ8PD(CB) is connected to the network.
- Page 8 Trap Receiver Settings (Fig. 3b, pg. 7): a. Enter up to five SNMP trap receiver IP addresses. When accessing the LINQ8PD(CB) remotely check with the network administrator for proper configuration. b. Click [Submit Trap Receiver IP Settings] button, a dialog box will display “New Trap Receiver IP settings will take effect after the server is rebooted” click “OK”.
- Page 9 Normally Closed Trigger input. Max Temp: The LINQ8PD(CB) will measure the ambient temperature of the enclosure it is mounted in. Entering a high temperature limit in Celsius, if this limit is exceeded an SNMP trap message and/or email notification will be generated.
- Page 10 4 years. Output Relay configuration (Fig. 7, pg. 10): Three (3) output relays of the LINQ8PD(CB) can be configured for various uses. From the pull down menu select the desired setting for each relay. Output Relay 1:...
- Page 11 3. Security Settings (Fig. 9, pg. 11): Click on [Security Settings] tab. The LINQ8PD(CB) security setting page will open. This section is used to enable/disable Secure Socket Layer (SSL) and to change Username and Password. SSL will encrypt all the communication Fig.
- Page 12 Click the button labeled Submit to save setting. 6. Updating Firmware: Firmware updates must be done using the Altronix Dashboard. For additional information refer to the Updating firmware / SSL certificate and Key section in the Altronix Dashboard setup/user manual.
- Page 13 Security Settings Events Log Help v1.99.22 Status Monday, Sept. 21 2015 [2:30 pm] Site ID: LINQ8 Minimize Minimize Others LINQ8PD ID: LINQ8 DEV PS1 Output Voltage 27.5 VDC FACP Status AC Status Normal Battery Charge Level 100 % Normal PS1 Load 2.55 A...
- Page 14 Notes: - 14 - LINQ8PD/LINQ8PDCB Available from A1 Security Cameras www.a1securitycameras.com email: sales@a1securitycameras.com...
- Page 15 Notes: LINQ8PD/LINQ8PDCB - 15 Available from A1 Security Cameras www.a1securitycameras.com email: sales@a1securitycameras.com...
- Page 16 Notes: Altronix is not responsible for any typographical errors. Product specifications are subject to change without notice. 140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: 718-567-9056 website: www.altronix.com, e-mail: info@altronix.com. Lifetime Warranty, Made in U.S.A. IILINQ8PD F27P MEMBER...