Toro Reelmaster 7000-D Operator's Manual page 5

•
Mow only in daylight or in good artificial light.
•
Before attempting to start the engine, disengage
all blade attachment clutches, shift into neutral,
and engage the parking brake.
•
Remember there is no such thing as a safe slope.
Travel on grass slopes requires particular care. To
guard against overturning:
– do not stop or start suddenly when going up
or downhill;
– machine speeds should be kept low on slopes
and during tight turns;
– stay alert for humps and hollows and other
hidden hazards;
– Do not turn sharply. Use care when reversing.
– Use counterweight(s) or wheel weights when
suggested in the operator's manual.
•
Stay alert for holes in the terrain and other hidden
hazards.
•
Watch out for traffic when crossing or near
roadways.
•
Stop the blades rotating before crossing surfaces
other than grass.
•
When using any attachments, never direct
discharge of material toward bystanders nor allow
anyone near the machine while in operation.
•
Never operate the machine with damaged guards,
shields, or without safety protective devices in
place. Be sure all interlocks are attached, adjusted
properly, and functioning properly.
•
Do not change the engine governor settings or
over-speed the engine. Operating the engine
at excessive speed may increase the hazard of
personal injury.
•
Before leaving the operator's position:
– stop on level ground;
– disengage the power take-off and lower the
attachments;
– change into neutral and set the parking brake;
– stop the engine and remove the key.
•
Disengage drive to attachments when transporting
or not in use.
•
Stop the engine and disengage drive to
attachment:
– before refuelling;
– before making height adjustment unless
adjustment can be made from the operator's
position.
– before clearing blockages;
– before checking, cleaning or working on the
mower;
– after striking a foreign object or if an abnormal
vibration occurs. Inspect the mower for
damage and make repairs before restarting
and operating the equipment.
•
Reduce the throttle setting during engine run-out
and, if the engine is provided with a shut-off valve,
turn the fuel off at the conclusion of mowing.
•
Keep hands and feet away from the cutting units.
•
Look behind and down before backing up to be
sure of a clear path.
•
Slow down and use caution when making
turns and crossing roads and sidewalks. Stop
cylinders/reels if not mowing.
•
Do not operate the machine when ill, tired, or
under the influence of alcohol or drugs.
•
Lightning can cause severe injury or death. If
lightning is seen or thunder is heard in the area, do
not operate the machine; seek shelter.
•
Use care when loading or unloading the machine
into a trailer or truck.
•
Use care when approaching blind corners, shrubs,
trees, or other objects that may obscure vision.
Maintenance and Storage
•
Keep all fasteners tight to be sure that the
equipment is in safe working condition.
•
Never store the equipment with fuel in the tank
inside a building where fumes may reach an open
flame or spark.
•
Allow the engine to cool before storing in any
enclosure.
•
To reduce the risk of fire, keep the engine,
silencer/muffler, battery compartment and fuel
storage area free of grass, leaves, or excessive
grease. Clean up oil or fuel spillage.
•
Keep all parts in good working condition and all
hardware and hydraulic fittings tightened. Replace
all worn or damaged parts and decals.
•
If the fuel tank has to be drained, do this outdoors.
•
Be careful during adjustment of the machine to
prevent entrapment of the fingers between moving
blades and fixed parts of the machine.
•
On multi-cylinder/multi-reel machines, take care
as rotating one cylinder/reel can cause other
cylinders/reels to rotate.
•
Disengage drives, lower the cutting units, set
parking brake, stop engine and remove key from
ignition. Wait for all movement to stop before
adjusting, cleaning or repairing.
•
Use jack stands to support components when
required.
•
Carefully release pressure from components with
stored energy.
•
Disconnect battery before making any repairs.
Disconnect the negative terminal first and the
5