Toro Reelmaster 7000-D Operator's Manual
27-inch verticutter cutting unit
Hide thumbs
Also See for Reelmaster 7000-D:
- Service manual (468 pages) ,
- Operator's manual (144 pages) ,
- Installation instructions (2 pages)
Related Manuals for Toro Reelmaster 7000-D
Summary of Contents for Toro Reelmaster 7000-D
- Page 1 Form No. 3456-938 Rev A 27-inch Verticutter Reelmaster ® 7000-D Cutting Unit Model No. 03731—Serial No. 407900000 and Up *3456-938* Register at www.Toro.com. Original Instructions (EN)
-
Page 2: Table Of Contents
Contents Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model Safety ............... 3 and serial numbers of your product ready. Figure 1 General Safety ........... -
Page 3: Safety
Remove all debris or other objects that might be • Use only accessories, attachments, and picked up and thrown by the blades of the cutting replacement parts approved by Toro. unit. Keep all bystanders away from the working area. Blade Safety •... -
Page 4: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal137-9706 137-9706 1. Cutting hazard of the hand or foot—shut off the engine, remove the key or disconnect the spark plug, wait for all moving parts to stop, and read the Operator’s Manual before performing maintenance. -
Page 5: Setup
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Verticutter Inspect the verticutter. Transport roller assembly Install the transport rollers. Cotter pin O-ring Install the O-ring and the grease fitting. Grease fitting Turf-compensation assembly Long bolt Install the turf-compensation spring... -
Page 6: Inspecting The Verticutter
Note: Determine the left and right sides of the machine from the normal operating position. Installing the Transport Rollers Inspecting the Verticutter Parts needed for this procedure: Parts needed for this procedure: Transport roller assembly Verticutter Cotter pin Procedure Procedure After the verticutter is removed from the box, inspect Secure a transport roller bracket to each side plate pin the following:... -
Page 7: Installing The O-Ring And The Grease Fitting
Installing the O-ring and the Grease Fitting Parts needed for this procedure: O-ring Grease fitting Procedure g028407 Figure 5 The grease fitting must be installed on the reel motor side of the verticutter. Use the following diagram to 1. Bolts 3. -
Page 8: Installing The Turf-Compensation
Installing the Adjusting the Verticutter Turf-Compensation Spring No Parts Required Parts needed for this procedure: Procedure Turf-compensation assembly Refer to Adjusting the Verticutter (page Long bolt Carriage bolt Flange locknut Flange nut Mounting the Verticutter Procedure Reel Install the turf compensation spring assembly on the same side as the reel motor (Figure 4 Figure... -
Page 9: Product Overview
Adjusting the Verticutter to enhance and expand its capabilities. Contact your Authorized Service Dealer or authorized Toro distributor or go to www.Toro.com for a list of all Adjusting the Blade Depth approved attachments and accessories. To ensure optimum performance and continued safety... - Page 10 Adjusting the Rear Grass Shield Tighten the flange nuts to lock the adjustment. Note: When operating in turf conditions where there Adjusting the Transport Rollers is excessive debris or thatch, open the rear discharge shield to help allow the debris to discharge from the Before the verticutters are lowered to the shop floor reel.
-
Page 11: Operating Tips
g031275 Figure 12 1. Cutting unit 1 5. Cutting unit 5 2. Cutting unit 2 6. Reel motor 3. Cutting unit 3 7. Weight 4. Cutting unit 4 Locking the Steering g196971 Figure 14 To lock (fix) the steering on the cutting units, secure 1. -
Page 12: Maintenance
Maintenance Lubricating the Verticutter Each verticutter has 5 grease fittings (Figure 16) that Using the Kickstand When must be lubricated weekly with No. 2 lithium grease. The lubrication points are the front roller (2), the rear Tipping the Cutting Unit roller (2), and the reel motor splines (1). -
Page 13: Removing The Verticutter Blades From The Shaft
Removing the Verticutter Installing the Verticutter Blades from the Shaft Blades Secure the end of the verticutter shaft, which Assemble a reel blade (Figure 18). has only one washer and nut, in a vise. Assemble a large spacer. On other end of shaft, rotate the nut Do not invert the reel blades when assembling counter-clockwise and remove the nut. -
Page 14: Optional Blade Spacing
Optional Blade Spacing Changing the configuration of the verticutter from the standard 1.20-inch spacing to the optional 0.94-inch spacing requires an additional 23 spacers (Part No. 140-5532) and an additional 5 carbide-tip blades (Part No. 106-8625) as shown in Figure g349402 Figure 19 1. -
Page 15: Servicing The Roller
Refer to your parts catalog or Roller Rebuild Tool Kit (Part No. 115-0803) (Figure contact your authorized Toro distributor for assistance. 20) are available for servicing the roller. The Roller Rebuild Kit includes all the bearings, bearing nuts,... - Page 16 Notes:...
- Page 17 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
- Page 18 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Regulations.
- Page 19 The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer. Toro uses this information to fulfil contractual obligations - such as to register your warranty, process your warranty claim or to contact you in the event of a product recall - and for legitimate business purposes - such as to gauge customer satisfaction, improve our products or provide you with product information which may be of interest.
- Page 20 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact your Authorized Toro Service Center.