Cypress CYW9P62S1-43012EVB-01 Manual page 18

9. PSoC 6 MCU user button (SW2): This button can be used to provide an input to the PSoC 6
MCU. Note that by default it connects the PSoC 6 MCU pin to ground when pressed, so you need
to configure the PSoC 6 MCU pin as a digital input with resistive pull-up for detecting the button
press. It also provides a wake-up source from low-power modes of the device.
10. Arduino-compatible power header (J1): This header powers the Arduino shields. It also has a
provision to power the kit though the VIN input.
11. PSoC 6 MCU reset button (SW1): This button is used to reset the PSoC 6 MCU. It connects the
PSoC 6 MCU reset (XRES) pin to ground.
12. PSoC 6 MCU debug and trace header (J12): This header can be connected to an Embedded
Trace Macrocell (ETM)-compatible programmer/debugger. This is not loaded by default.
13. PSoC 6 MCU program and debug header (J11): This 10-pin header allows you to program and
debug the PSoC 6 MCU using an external programmer such as MiniProg4.
14. Arduino Uno R3-compatible I/O headers (J2, J3, and J4): These I/O headers bring out pins
from the PSoC 6 MCU to interface with Arduino shields. Some of these pins are multiplexed with
onboard peripherals and are not connected to the PSoC 6 MCU by default. For a detailed infor-
mation on how to rework the kit to access these pins, see
15. CapSense slider (SLIDER) and buttons (BTN0 and BTN1): The CapSense touch-sensing
slider and two buttons, all of which are capable of both self-capacitance (CSD) and mutual-
capacitance (CSX) operation, allow you to evaluate Cypress' fourth-generation CapSense tech-
nology. The slider and buttons have a 1-mm acrylic overlay for smooth touch sensing.
16. PSoC 6 MCU VDDIO2 current measurement jumper (J18): An ammeter can be connected to
this jumper to measure the current consumed by the PSoC 6 MCU VDDIO2 power domain. This
jumper is not loaded by default on the board. Before populating the jumper for current measure-
ments, ensure that R94 is removed.
17. CYW43012 VDDIO current measurement jumper(J17): An ammeter can be connected to this
jumper to measure the current consumed by the CYW43012 VDDIO power domain.
18. Cypress serial NOR flash memory (S25FS512S, U3): A S25FS512S NOR flash of 512-Mbit
capacity is connected to the Quad SPI interface of the PSoC 6 MCU. The NOR device can be
used for both data and code memory with execute-in-place (XIP) support and encryption.
19. Cypress PSoC 6 (1M) with CYW43012 USI SiP Carrier Module (CYW9P62S1-43012CAR-01,
MOD1): This kit is designed to highlight the features of the PSoC 6 MCU on the CYW9P62S1-
43012CAR-01. For details, see
designed to highlight the features of the PSoC 6 MCU. For details on PSoC 6 MCU pin mapping,
refer to Table 2-1 on page
20. USI WM-BAC-CYW-50 SiP module: WM-BAC-CYW-50 is an SiP module that includes the
PSoC 6 MCU, CY8C6247FDI-D52 and CYW43012 (Wi-Fi + Bluetooth combo device). The mod-
ule provides 2.4 GHz and 5 GHz dual-band WLAN and Bluetooth functionality and complies with
IEEE 802.11a/b/g/n and Bluetooth Version 5.0.
21. Wi-Fi/BT antenna: This is an onboard antenna connected to the Wi-Fi and Bluetooth module.
CYW9P62S1-43012EVB-01 PSoC 62S1 Wi-Fi BT Pioneer Kit Guide, Doc. # 002-28722 Rev. *B
CYW9P62S1-43012CAR-01 (MOD1) on page
13.
Table 2-1 on page 13.
26. This kit is
Kit Operation
18