Cypress CYW9P62S1-43012EVB-01 Manual page 14

Table 2-1. PSoC 62S1 Wi-Fi BT Pioneer Board Pinout (continued)
Pin
P1[5]
P5[0]
P5[1]
P5[2]
P5[3]
P5[4]
P5[5]
P5[6]
P5[7]
P6[4]
P6[5]
P6[6]
P6[7]
P7[0]
P7[1]
P7[2]
P7[7]
P9[0]
P9[1]
P9[2]
P9[3]
P9[4]
CYW9P62S1-43012EVB-01 PSoC 62S1 Wi-Fi BT Pioneer Kit Guide, Doc. # 002-28722 Rev. *B
Primary On-board Secondary On-board
Function
Orange user LED GPIO on non-Arduino
(LED8) header IO7 (J24.2)
UART_RX Arduino D0 (J4.1)
UART_TX Arduino D1 (J4.2)
UART_RTS Arduino D2 (J4.3)
UART_CTS Arduino D3 (J4.4)
Arduino D4 (J4.5)
Arduino D5 (J4.6)
Arduino D6 (J4.7)
Arduino D7 (J4.8)
PSoC 6 MCU JTAG
Arduino A2 (J2.5)
TDO/SWD SWO
PSoC 6 MCU JTAG
Arduino A3 (J2.7)
PSoC 6 MCU JTAG
TMS/SWD SWDIO
PSoC 6 MCU JTAG
TCK/SWD SWCLK
CapSense Button1 GPIO on non-Arduino
TX header IO9 (J21.2)
CapSense CINTA
CapSense CINTB
CapSense CMOD
CapSense Slider0 GPIO on non-Arduino
RX header IO10 (J21.3)
CapSense Slider1 GPIO on non-Arduino
RX header IO11 (J21.4)
CapSense Slider2 GPIO on non-Arduino
RX header IO12 (J21.5)
CapSense Slider3 GPIO on non-Arduino
RX header IO13 (J21.6)
CapSense Slider4 GPIO on non-Arduino
RX header IO14 (J21.7)
Function
–
Remove R21 to disconnect from KitProg3.
Remove R61 to disconnect from KitProg3.
Remove R19 to disconnect from KitProg3.
Remove R18 to disconnect from KitProg3.
– –
– –
– –
– –
Remove R4 to disconnect from Arduion A2.
Populate R3 to connect to PSoC 6 MCU
JTAG TDO/SWD SWO.
Remove R8 to disconnect from Arduino A3.
Populate R7 to connect to PSoC 6 MCU
TDI
JTAG TDI.
– –
– –
Remove R25 to disconnect from CapSense.
Populate R143 to connect to GPIO on non-
Arduino header.
– –
– –
– –
Remove R28 to disconnect from CapSense.
Populate R142 to connect to GPIO on non-
Arduino header.
Remove R29 to disconnect from CapSense.
Populate R152 to connect to GPIO on non-
Arduino header.
Remove R30 to disconnect from CapSense.
Populate R153 to connect to GPIO on non-
Arduino header.
Remove R31 to disconnect from CapSense.
Populate R151 to connect to GPIO on non-
Arduino header.
Remove R32 to disconnect from CapSense.
Populate R149 to connect to GPIO on non-
Arduino header.
Kit Operation
Connection details
14