Table of Contents
Advertisement
Redback® A 4595A School Lockdown Controller
4.3 A 4597 Fire Test/Fire Remote Plate
The A 4597 wall plate provides the means to remotely operate the Fire Test and Fire Alarm tones of the A 4595A.
The switches are momentary operation and must be pressed for up to 3 seconds to activate. The switches have protective
"flip up" covers to prevent accidental operation.
Connection is made to the A 4595A via standard Cat5e cabling as shown in Fig 4.2C. There are two RJ45 ports on the
rear of the A 4597 wall plate, either of which can be used. These are connected in the same manner as the A 4598 wall
plates, and can be daisy chained in line with the A 4598 plates.
NOTE: The FIre Test and Fire tones cannot be triggered by any other means than the A 4597 wall plate.
22
Redback® Proudly Made In Australia
DIP Switch Settings
ID
1
2
3
4
5
6
1
ON
OFF
OFF
OFF
OFF
OFF
2
OFF
ON
OFF
OFF
OFF
OFF
3
ON
ON
OFF
OFF
OFF
OFF
4
OFF
OFF
ON
OFF
OFF
OFF
5
ON
OFF
ON
OFF
OFF
OFF
6
OFF
ON
ON
OFF
OFF
OFF
7
ON
ON
ON
OFF
OFF
OFF
8
OFF
OFF
OFF
ON
OFF
OFF
9
ON
OFF
OFF
ON
OFF
OFF
10
OFF
ON
OFF
ON
OFF
OFF
11
ON
ON
OFF
ON
OFF
OFF
12
OFF
OFF
ON
ON
OFF
OFF
13
ON
OFF
ON
ON
OFF
OFF
14
OFF
ON
ON
ON
OFF
OFF
15
ON
ON
ON
ON
OFF
OFF
16
OFF
OFF
OFF
OFF
ON
OFF
17
ON
OFF
OFF
OFF
ON
OFF
18
OFF
ON
OFF
OFF
ON
OFF
19
ON
ON
OFF
OFF
ON
OFF
20
OFF
OFF
ON
OFF
ON
OFF
21
ON
OFF
ON
OFF
ON
OFF
22
OFF
ON
ON
OFF
ON
OFF
23
ON
ON
ON
OFF
ON
OFF
24
OFF
OFF
OFF
ON
ON
OFF
25
ON
OFF
OFF
ON
ON
OFF
26
OFF
ON
OFF
ON
ON
OFF
27
ON
ON
OFF
ON
ON
OFF
28
OFF
OFF
ON
ON
ON
OFF
29
ON
OFF
ON
ON
ON
OFF
30
OFF
ON
ON
ON
ON
OFF
31
ON
ON
ON
ON
ON
OFF
32
OFF
OFF
OFF
OFF
OFF
ON
CASCADING THE A 4597 PLATES
If more than one remote wall plate is required then the
A 4597 wall plates can be connected back to the A 4595A
using any of the four Rj45 ports supplied. If more than four
wall plates are required then they can be cascaded together
back to the A 4595A as shown in Fig 4.2C.
A Maximum of 16 combined wall plates (A 4597 or A 4598)
is recommended, but up to 63 wall plates can be connected.
(If more than 16 wall plates are required contact Altronics for
configuration details).
Every wall plate must have a unique ID which is set by the
DIP switches which are accessed on the rear of the unit. A
maximum of 63 ID's are available. Fig 4.3B illustrates the DIP
switch ID settings.
DIP Switches 7-8 are not used.
DIP Switch Settings
ID
1
2
3
4
5
33
ON
OFF
OFF
OFF
OFF
34
OFF
ON
OFF
OFF
OFF
35
ON
ON
OFF
OFF
OFF
36
OFF
OFF
ON
OFF
OFF
37
OFF
ON
ON
OFF
OFF
38
OFF
ON
ON
OFF
OFF
39
ON
ON
ON
OFF
OFF
40
OFF
OFF
OFF
ON
OFF
41
ON
OFF
OFF
ON
OFF
42
OFF
ON
OFF
ON
OFF
43
ON
ON
OFF
ON
OFF
44
OFF
OFF
ON
ON
OFF
45
ON
OFF
ON
ON
OFF
46
OFF
ON
ON
ON
OFF
47
ON
ON
ON
ON
OFF
48
OFF
OFF
OFF
OFF
ON
49
ON
OFF
OFF
OFF
ON
50
OFF
ON
OFF
OFF
ON
51
ON
ON
OFF
OFF
ON
52
OFF
OFF
ON
OFF
ON
53
ON
OFF
ON
OFF
ON
54
OFF
ON
ON
OFF
ON
55
ON
ON
ON
OFF
ON
56
OFF
OFF
OFF
ON
ON
57
ON
OFF
OFF
ON
ON
58
OFF
ON
OFF
ON
ON
59
ON
ON
OFF
ON
ON
60
OFF
OFF
ON
ON
ON
61
ON
OFF
ON
ON
ON
62
OFF
ON
ON
ON
ON
63
ON
ON
ON
ON
ON
Fig 4.3B
6
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
www.altronics.com.au
- Quick Links:
- Lockdown Modes
Hide quick links:
Advertisement
Table of Contents
