GETTING STARTED Product View Battery Battery Wand Clips Wand Spacer Power Cable* Blocks Installation Brackets Headrail Wire Saddle Programming Button* Magnetic Hold-Down Brackets (Optional) Bottom Rail Balance Weight Weight Remote Clips *The power cable, PowerView motor, and programming button are always located on the right side of ®...
GETTING STARTED Thank you for purchasing Hunter Douglas Vignette Modern Roman Shades with PowerView ® ® Motorization. With proper installation, operation, and care, your new shades will provide years of beauty and performance. Please thoroughly review this instruction booklet and the enclosed packing list before beginning the installation.
INSTALLATION Installation Overview To install your shade, you will need to perform the following three steps: STEP 1: Install the Brackets STEP 2: Install the Shade STEP 3: Connect the Power Source STEP 1 — Install the Brackets Your order will include the correct number of installation brackets for your shade width, as ■...
INSTALLATION Mount the Installation Brackets — Inside Mount Measure and mark 3" in from each jamb (two bracket widths) for bracket location. ■ If more than two installation brackets came with your order, space additional bracket(s) ➤ evenly between the two end brackets and mark the location. Mount into wood whenever possible.
INSTALLATION Mount the Installation Brackets — Outside Mount Center the headrail over the window opening at the desired height. Use a pencil to lightly ■ mark each end of the headrail. Alternatively, measure the width of the headrail and use that width to mark the headrail ➤...
INSTALLATION If the shade will be powered by a battery wand: Attach the installation brackets with the ■ " and " spacer blocks. Use 2" #6 hex head screws (not provided). The solid side of the spacer blocks faces the ➤...
INSTALLATION STEP 2 — Install the Shade Install the Battery Wand Clips Attach each battery wand clip to the rear of the headrail, avoiding the installation brackets. NOTE: The battery wand clips can simply slide to clear the installation brackets. Mount the Headrail CAUTION: Be sure the cables do not become Installation...
INSTALLATION STEP 3 — Connect the Power Source ■ NOTE: When power is connected to the motor, a green LED inside the programming button housing will flash to indicate the shade is ready for operation. Refer to the appropriate page based on the ordered power source. ■...
Page 11
INSTALLATION If You Have a Satellite Battery Pack... Mount the Satellite Battery Pack Wall Mount Bracket Decide where you want to attach the wall mount bracket. ■ A satellite battery pack may be mounted in any orientation. Mark the screw holes. ■...
Page 12
INSTALLATION If You Have an 18V DC Power Supply... Connect the Power Supply Plug the power cable from the shade into ■ Power Cable the extension cable. from Shade Plug the other end of the extension cable ■ into the 18V DC Power Supply. Wire Retainers Plug the 18V DC Power Supply into a ■...
Page 13
INSTALLATION If You Have a 18V DC Power Supply with Daisy-Chain Connections... The daisy-chain feature allows up to three PowerView motorized shades to be powered by a ® single 18V DC Power Supply. However, each shade has its own RF receiver and can operate independently.
INSTALLATION Attach Magnetic Hold-Down Brackets (Optional) Lower the shade until it is fully lowered and rotated back toward the window. ■ Attach the magnetic hold-down brackets onto the bottom ■ Magnetic Hold-Down rail just inside the end caps. The brackets will attach into Bracket the channel in the middle of the bottom rail.
OPERATION Testing the Shade Check the Power Cord Check the headrail to ensure the power cord is not visible. ■ Test the Shade Use the programming button to test the shade and ensure that the motor and power source are working correctly.
OPERATION Using the PowerView Remote ® First, activate the remote by pulling both plastic tabs from the back battery compartment. OPEN Group 4 Group 3 Group 5 Group 2 Group 1 Group 6 LEFT ARROW RIGHT ARROW No function for No function for this product this product...
® For information regarding operation and programming of the PowerView Scene Controller, refer to ® your PowerView Motorization Scene Controller Guide or to the online PowerView Step-by-Step Guide at hunterdouglas.com/operating-systems/motorized/powerview-motorization/manuals. PowerView App Operation ® The PowerView Hub is required for PowerView App operation.
OPERATION Troubleshooting If your shade is not operating correctly: First review the guide that came with your control device. ■ Refer to the following troubleshooting procedures for specific solutions for your shade. ■ If questions remain, please contact Hunter Douglas Consumer Support at 1-888-501-8364. Problem The shade will not snap into the installation brackets.
Page 19
The shade may need to be reset. Refer to “Resetting the Shade (If Necessary)” on page 15. For information regarding operation and programming of the PowerView ® remote, refer to your PowerView Motorization Remote Control Guide or to the ® Step-by-Step Guide at hunterdouglas.com/operating- online PowerView ® systems/motorized/powerview-motorization/manuals.
Page 20
OPERATION Problem Adjacent shades do not roll up evenly. Solution It is considered normal if the roll-up on both shades is within " of each other. If one shade rolls up tighter than another, repeatedly lower and raise both shades. The shade may need to be reset. Refer to “Resetting the Shade (If Necessary)”...
CARE Removing the Shade Fully raise the shade. ■ While holding the headrail, place the ■ blade of a small screwdriver on the Push installation bracket’s locking tab. Insert the screwdriver between the ➤ arrows on the bottom tabs. CAUTION: Be very careful not to tear or Locking damage the fabric.
Page 22
Allow the shade to dry in the completely lowered position. ■ Injection/Extraction Cleaning Vignette Modern Roman Shades can be cleaned by a professional using the injection/extraction method of deep cleaning. CAUTION: Do not use the injection/extraction method of deep cleaning on the headrail or bottom rail fabric.
Hunter Douglas Europe B.V. Piekstraat 2, 3071 EL Rotterdam, The Netherlands certify and declare under our sole responsibility that assembly PV13 conforms with the essential requirements of RED 2014/53/EU. A copy of the original declaration of conformity may be found at: www.hunterdouglas.com/RFcertifications.
Page 24
If you are not thoroughly satisfied, simply contact Hunter Douglas at (888) 501-8364 or visit hunterdouglas.com. In support of this policy of consumer satisfaction, we offer our Lifetime Limited Warranty as described below.