Related Manuals for Pilz PNOZ m ES 14DO
Summary of Contents for Pilz PNOZ m ES 14DO
- Page 1 PNOZ m ES 14DO Configurable control systems PNOZmulti 2 Operating Manual-1004299-EN-02...
- Page 2 Preface This document is a translation of the original document. All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made for internal purposes. Suggestions and comments for improving this documentation will be gratefully received.
-
Page 3: Table Of Contents
General installation guidelines Dimensions in mm Connecting the base unit and expansion modules Section 6 Commissioning General wiring guidelines Connection Section 7 Operation Messages Section 8 Technical details Section 9 Order reference Product Accessories Operating Manual PNOZ m ES 14DO 1004299-EN-02... -
Page 4: Operating Manual Pnoz M Es 14Do
Introduction Introduction Validity of documentation This documentation is valid for the product PNOZ m ES 14DO from Version HW:01, FW:01.00 . This operating manual explains the function and operation, describes the installation and provides guidelines on how to connect the product. - Page 5 Introduction INFORMATION This gives advice on applications and provides information on special fea- tures. Operating Manual PNOZ m ES 14DO 1004299-EN-02...
-
Page 6: Overview
Scope of supply Expansion module PNOZ m ES 14DO Jumper Unit features Using the product PNOZ m ES 14DO: Expansion module for connection to a base unit from the configurable control system PNOZmulti 2 . The product has the following features:... -
Page 7: Front View
Overview Front view Serial number Firmware version (FW) Hardware version (HW) Legend: 0 V, 24 V: Supply connections Outputs O0 – O13 LEDs: – POWER – – Diag – Fault – O Fault Operating Manual PNOZ m ES 14DO 1004299-EN-02... -
Page 8: Safety
It is the company’s responsibility only to employ personnel who: Are familiar with the basic regulations concerning health and safety / accident preven- tion Have read and understood the information provided in this description under "Safety" Operating Manual PNOZ m ES 14DO 1004299-EN-02... -
Page 9: Warranty And Liability
Do not open the housing or make any unauthorised modifications. Please make sure you shut down the supply voltage when performing maintenance work (e.g. exchanging contactors). Operating Manual PNOZ m ES 14DO 1004299-EN-02... -
Page 10: Function Description
"PNOZmulti System Expan- sion". Block diagram 24 V Output Module Supply Supply Data . . . (ST) . . . O0 O1 O2 O11 O12 O13 Operating Manual PNOZ m ES 14DO 1004299-EN-02... -
Page 11: Installation
Connect the base unit and the expansion modules as described in the operating manuals for the base modules. The terminator must be fitted to the last expansion module Install the expansion module in the position configured in the PNOZmulti Configurator. Operating Manual PNOZ m ES 14DO 1004299-EN-02... - Page 12 Please refer to the document "PNOZmulti System Expansion" for details of the number of modules that can be connected to the base unit and the module types. The module for standard applications has to be placed to the right of the safe expansion modules. Operating Manual PNOZ m ES 14DO 1004299-EN-02...
-
Page 13: Commissioning
Protect the supply voltage as follows: – Circuit breaker, characteristic C - 10 A – Blow-out fuse, slow, 10 A Connection Supply voltage Connection example Single output Two outputs parallel Operating Manual PNOZ m ES 14DO 1004299-EN-02... -
Page 14: Operation
Supply voltage for the semiconductor outputs is not present Expansion module PNOZ m ES 14DO running without error. Expansion module PNOZ m ES 14DO is in a STOP condi- tion. Internal error on the expansion module PNOZ m ES 14DO or on the overall system. -
Page 15: Technical Details
Max. transient pulsed current 1,4 A Max. internal voltage drop 500 mV Switch-off delay 1 ms Potential isolation Short circuit-proof Utilisation category in accordance with UL Voltage 24 V DC P. D. Current 0,5 A Operating Manual PNOZ m ES 14DO 1004299-EN-02... - Page 16 Basic insulation Rated surge voltage 2500 V Mechanical data Mounting position Horizontal on top hat rail DIN rail Top hat rail 35 x 7,5 EN 50022 Recess width 27 mm Material Bottom Front Operating Manual PNOZ m ES 14DO 1004299-EN-02...
- Page 17 Spring-loaded terminals: Terminal points per connec- tion Stripping length with spring-loaded terminals 9 mm Dimensions Height 101,4 mm Width 22,5 mm Depth 120 mm Weight 100 g Where standards are undated, the 2016-05 latest editions shall apply. Operating Manual PNOZ m ES 14DO 1004299-EN-02...
-
Page 18: Order Reference
751 004 Set screw terminals 1 set of screw terminals 750 004 Terminator, jumper Product type Features Order No. PNOZ mm0.xp connector Jumper yellow/black to connect the modules, 10 piece 779 260 left Operating Manual PNOZ m ES 14DO 1004299-EN-02... - Page 19 Back cover Support Technical support is available from Pilz round the clock. Americas Australia Scandinavia Brazil +61 3 95600621 +45 74436332 +55 11 97569-2804 Spain Canada Europe +34 938497433 +1 888-315-PILZ (315-7459) Austria Switzerland Mexico +43 1 7986263-0 +41 62 88979-30...