Table of Contents
Advertisement
Quick Links
U7T Series Bullet Camera
User Manual
Thank you for purchasing our product. If there are any
questions, or requests, do not hesitate to contact the
dealer.
This manual applies to the models below:
Type
Type I Camera
Type II Camera
This manual may contain several technical incorrect
places or printing errors, and the content is subject to
change without notice. The updates will be added to
the new version of this manual. We will readily improve
or update the products or procedures described in the
manual.
TURBO HD
User Manual
Model
DS-2CE16U7T-ITF
DS-2CE16U7T-IT3F
DS-2CE16U7T-IT5F
0100001081124
Advertisement
Table of Contents
Related Manuals for HIKVISION TURBO HD U7T Series
Summary of Contents for HIKVISION TURBO HD U7T Series
- Page 1 TURBO HD U7T Series Bullet Camera User Manual User Manual Thank you for purchasing our product. If there are any questions, or requests, do not hesitate to contact the dealer. This manual applies to the models below: Type Model Type I Camera DS-2CE16U7T-ITF DS-2CE16U7T-IT3F Type II Camera...
-
Page 2: Regulatory Information
Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. - Page 3 Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions”. Warnings: Serious injury or death may occur if any of the warnings are neglected.
- Page 4 Keep the camera away from liquid while in use for non-water-proof device. While in delivery, the camera shall be packed in its original packing, or packing of the same texture. Mark Description Table 0-1 Mark Description Mark Description DC Voltage 1 Introduction 1.1 Product Features...
-
Page 5: Installation
2 Installation Before you start: Make sure that the device in the package is in good condition and all the assembly parts are included. Make sure that all the related equipment is power-off during the installation. Check the specification of the products for the ... - Page 6 6. Power on the camera to check whether the image on the monitor is gotten from the optimum angle. If not, adjust the camera according to the figure below to get an optimum angle. Pan Position [0° to 360°] P Screw Rotation Position Tilt Position [0°...
- Page 7 Junction Box Body Figure 2-6 Secure the Junction Box to the Wall/Ceiling 7. Route the cables through the bottom cable hole, or the side cable hole of the junction box. 8. Combine the junction box cover with its body. Figure 2-7 Combine the Junction Box Cover back to its Body 9.
- Page 8 Figure 2-9 Install the Camera to the Ceiling/Wall Note: The supplied screw package contains self-tapping screws, and expansion bolts. For cement wall/ceiling, expansion bolts are required to fix the camera. For wooden wall/ceiling, self-tapping screws are required. 5. Connect the corresponding power cord, and video cable.
- Page 9 4. Install the camera on the junction box’s cover with three PM4 × 10 screws. 5. Install the junction box’s body to the ceiling/wall with supplied screws. Figure 2-12 Install the Junction Box to the Ceiling/Wall 6. Route the cables through the bottom cable hole, or the side cable hole of the junction box.
-
Page 10: Menu Description
3 Menu Description Please follow the steps below to call the menu. NOTE: Menu description part is only for your reference. It might have some differences due to the specific model that you have. Steps: 1. Connect the camera with the TVI DVR, and the monitor, shown as the figure 3-1. -
Page 11: Video Format
2). Click Iris + to confirm the selection. 3). Click left/right direction button to adjust the value of the selected item. 3.1 VIDEO FORMAT You can set the video format as 8MP@12.5 fps, 8 MP@15fps, 5MP@20fps, 4MP@25fps, 4MP@30fps, 1080P@25fps, and 1080P@30fps. Note: When switching the video output as CVBS, you can ... - Page 12 3.3 DAY/NIGHT COLOR, BW (Black White), and AUTO are selectable for DAY/NIGHT switch. COLOR The image is colored in day mode all the time. B & W (Black and White) The image is black and white all the time, and the IR LIGHT turns on in the poor light conditions.
-
Page 13: Video Settings
set the value from 1 to 9. The larger the value is, the more sensitive the camera is. Nà D Threshold (Night to Day Threshold) Night to Day Threshold is used to control the sensitivity of switching the night mode to the day mode. You can set the value from 1 to 9. -
Page 14: Factory Default
CONTRAST This feature enhances the difference in color and light between parts of an image. You can set the CONTRAST value from 1 to 9. SHARPNESS Sharpness determines the amount of detail an imaging system can reproduce. You can set the SHARPNESS value from 1 to 9.