Table of Contents
Advertisement
Quick Links
TURBO HD
H1T Series Bullet Camera
User Manual
UD03834B
User Manual
Thank you for purchasing our product. If there are any
questions, or requests, do not hesitate to contact the
dealer.
This manual applies to the models below:
Type
Type I
Camera
Type II
Camera
This manual may contain several technical incorrect
places or printing errors, and the content is subject to
change without notice. The updates will be added to
the new version of this manual. We will readily improve
or update the products or procedures described in the
manual.
Questo manuale d'istruzione è fornito da trovaprezzi.it. Scopri tutte le offerte per
DS-2CE16F7T-IT
o cerca il tuo prodotto tra le
migliori offerte di Videosorveglianza
Model
DS-2CE16H1T-IT
DS-2CE16H1T-IT1
DS-2CE16H1T-IT3
DS-2CE16H1T-IT5
0100001061129
Hikvision
Advertisement
Table of Contents
Related Manuals for HIKVISION TURBO HD DS-2CE16H1T-IT
Summary of Contents for HIKVISION TURBO HD DS-2CE16H1T-IT
- Page 1 Questo manuale d’istruzione è fornito da trovaprezzi.it. Scopri tutte le offerte per Hikvision DS-2CE16F7T-IT o cerca il tuo prodotto tra le migliori offerte di Videosorveglianza TURBO HD H1T Series Bullet Camera User Manual UD03834B User Manual Thank you for purchasing our product. If there are any questions, or requests, do not hesitate to contact the dealer.
-
Page 2: Regulatory Information
Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. - Page 3 Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected.
- Page 4 The sensor may be burned out by a laser beam, so when any laser equipment is in using, make sure that the surface of sensor will not be exposed to the laser beam. Do not place the camera in extremely hot, cold, dusty ...
-
Page 5: Product Features
1 Introduction Product Features The camera is applicable for both indoor and outdoor conditions, and the application scenarios include road, warehouse, underground parking lot, bar, etc.. The main features are as follows: High performance CMOS sensor Low illumination, 0.01 Lux@(F1.2, AGC ON), 0 Lux ... - Page 6 Make sure that all the related equipment is power-off during the installation. Check the specification of the products for the installation environment. Check whether the power supply is matched with your power output to avoid the damage. Make sure the wall is strong enough to withstand ...
- Page 7 1). Loosen the P screw to adjust the pan position [0° to 360°]. Tighten the screw after completing the adjustment. 2). Loosen the T screw to adjust the tilt position [0° to 90°]. Tighten the screw after completing the adjustment. 3).
- Page 8 Junction Box Figure 2-6 Fix the Junction Box to the Wall/Ceiling 7. Route the cables through the cable hole, or the side opening of the junction box. 8. Combine the junction box cover with its body. Figure 2-7 Fix the Junction Box Cover back to its Body 9.
-
Page 9: Ceiling/Wall Mounting With Junction Box
Figure 2-9 Fix the Camera to the Ceiling Note: In the supplied screw package, both self-tapping screws and expansion blots are contained. If the ceiling/wall is cement, expansion blots are required to fix the camera. If the ceiling/wall is wooden, self-tapping screws are required. -
Page 10: Menu Description
6. Route the cables through the cable hole, or the side opening of the junction box. 7. Combine the junction box cover with its body with supplied screws on the junction box’s cover. Figure 2-12 Combine the Junction Box’s Cover with its Body 8. -
Page 11: Output Mode
RESOLUTION OUTPUT FRAME RATE MODE VIDEO OUT RETURN SHUTTER FLICKER MODE EXPOSURE BRIGHTNESS D-WDR RETURN MAIN MENU BACKLIGHT WHITE AWC- SET MANUAL COLOR DAY & NIGHT AUTO MIRROR SPECIAL LANGUAGE RETURN SHARPNESS ADJUST MONITOR RETURN SAVE & END EXIT RESET NOT SAVE Figure 3-2 Main Menu Overview 3.1 OUTPUT MODE... - Page 12 (National Television System Committee) is the analog television system that is used in most of North America, parts of South America, Myanmar, South Korea, etc.. 3.2 EXPOSURE Exposure describes the brightness-related parameters. You can adjust the image brightness by the SHUTTER FLICKER MODE, AGC, BRIGHTNESS, and D-WDR in different light conditions.
-
Page 13: Day & Night
3.4 WB (White Balance) White balance is the white rendition function of the camera to adjust the color temperature according to the environment. It can remove the unrealistic color casts in the image. MANUAL, ATW (Auto-Tracking White Balance), AWC→SET are selectable. Manual You can set the R GAIN/B GAIN value from 0 to 255 to adjust the shades of red/blue color of the image. - Page 14 WHITE DPC: White DPC is the pixel on CCD or CMOS sensor that appear completely white. Move the cursor to the white DPC, and press Iris+ to enter the white DPC configuration interface. BLACK DPC: Black DPC is the pixel on CCD or CMOS sensor that appear completely black.