Table of Contents
Advertisement
Quick Links
TURBO HD
4K Series Bullet Camera
User Manual
User Manual
Thank you for purchasing our product. If there are any
questions, or requests, do not hesitate to contact the
dealer.
This manual applies to the models below:
Type
Model
Type I Camera
DS-2CE17U8T-IT
Type II Camera
DS-2CE18U8T-IT3
This manual may contain several technical incorrect
places or printing errors, and the content is subject to
change without notice. The updates will be added to
the new version of this manual. We will readily improve
or update the products or procedures described in the
manual.
0100001071023
Advertisement
Table of Contents
Related Manuals for HIKVISION DS-2CE17U8T-IT
Summary of Contents for HIKVISION DS-2CE17U8T-IT
-
Page 1: User Manual
This manual applies to the models below: Type Model Type I Camera DS-2CE17U8T-IT Type II Camera DS-2CE18U8T-IT3 This manual may contain several technical incorrect places or printing errors, and the content is subject to change without notice. The updates will be added to the new version of this manual. -
Page 2: Regulatory Information
Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. - Page 3 Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions”. Warnings: Serious injury or death may occur if any of the warnings are neglected.
-
Page 4: Installation
To avoid heat accumulation, good ventilation is required for the operating environment. Keep the camera away from liquid while in use for non-water-proof device. While in delivery, the camera shall be packed in its original packing, or packing of the same texture. Mark Description Table 0-1 Mark Description Mark... - Page 5 Check the specification of the products for the installation environment. Check whether the power supply is matched with your power output to avoid the damage. Make sure the wall is strong enough to withstand three times the weight of the camera and the mount. If the wall is cement, insert expansion bolts before ...
- Page 6 Pan Position [0° to 360°] P Screw Tilt Position [0° to 180°] T Screw Rotation Position R Screw [0° to 360°] Figure 2-3 3-axis Adjustment 1). Loosen the P screw to adjust the pan position [0° to 360°]. Tighten the screw after completing the adjustment.
- Page 7 Figure 2-6 Fix the Junction Box to the Wall/Ceiling 7. Route the cables through the bottom cable hole (optional), or the side cable hole of the junction box. 8. Combine the junction box cover with its body. Figure 2-7 Fix the Junction Box Cover back to its Body 9.
-
Page 8: Ceiling/Wall Mounting With Junction Box
Figure 2-9 Fix the Camera to the Ceiling Note: The supplied screw package contains self-tapping screws, and expansion bolts. For cement wall/ceiling, expansion bolts are required to fix the camera. For wooden wall/ceiling, self-tapping screws are required. 5. Connect the corresponding power cord, and video cable. - Page 9 4. Fix the camera on the junction box’s cover with three supplied screws. Figure 2-11 Fix the Camera on the Junction Box’s Cover 5. Secure the junction box’s body with supplied screws on the ceiling/wall. Figure 2-12 Install the Junction Box 6.
-
Page 10: Menu Description
3 Menu Description Purpose: Call the menu by clicking button on the PTZ Control interface, or call preset No.95. Steps: 1. Connect the camera with the TVI DVR, and the monitor shown as the Figure 3-1. Figure 3-1 Connection 2. Power on the analog camera, TVI DVR, and the monitor to view the image on the monitor. - Page 11 3.3 Settings 3.3.1 Exposure Exposure describes the brightness-related parameters, which can be adjusted by Brightness, Exposure Mode, AGC, and Slow Shutter. Figure 3-3 Exposure Brightness Brightness refers to the brightness of the image. You can set the brightness value from 1 to 10 to darken or brighten the image.
- Page 12 3.3.2 WB (White Balance) White balance, the white rendition function of the camera, is to adjust the color temperature according to the environment. It can remove unrealistic color casts in the image. You can set WB mode as Auto, Manual, or Natural.
- Page 13 Day to Night Threshold is used to control the sensitivity of switching the day mode to the night mode. You can set the value from 1 to 9. The larger the value is, the more sensitive the camera is. Nà D Threshold (Night to Day Threshold) ...
- Page 14 3.3.5 Facroty Default Click Iris+ to enter the submenu, and click OK to reset all the settings to the factory default. Click Cancel to give up the reset settings. 3.3.6 Save & Exit Move the cursor to Save & Exit, and click Iris+ to save the settings and exit the menu.
Need help?
Do you have a question about the DS-2CE17U8T-IT and is the answer not in the manual?
Questions and answers