Subscribe to Our Youtube Channel
Related Manuals for SIIG AV-GM04A3-S1-IR
Summary of Contents for SIIG AV-GM04A3-S1-IR
- Page 1 HDMI extender over IP with IR and RS-232 To avoid EMI issue, complete STP Cat6 cable is strongly recommended! P/N: AV-GM04A3-S1...
-
Page 2: Table Of Contents
However, like all electronic equipments, the AV-GM04A3-S1-IR should be used with care. Please read and follow the safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit. -
Page 3: Introduction
IR pass-through path and RS-232 serial port control. The AV-GM04A3-S1-IR is also a HD video distribution solution for digital signage. With SP-5022I, AV-GM04A3-S1-IR can also support s a 10 layer “daisy-chain” for up to 1000M or even longer. FEATURES ●... -
Page 4: Specifications
SPECIFICATIONS Model Name AV-GM04A3-S1-IR Technical AV-GM04A3-S1-IR[Tx] AV-GM04A3-S1-IR[Rx] Role of usage Transmitter [TX] Receiver [RX] HDMI compliance HDMI HDCP compliance Video bandwidth Single-link 225MHz [6.75Gbps] Video support 480i / 480p / 720p / 1080i / 1080p60 HDMI over UTP Full HD (1080p)-100m (330ft) [CAT.X]... -
Page 5: Panel Descriptions
Relative humidity 20~90% RH [no condensation] PANEL DESCRIPTIONS Transmitting unit ► AV-GM04A3-S1-IR-TX Front Panel HDMI IN: Connects to a HDMI source with a HDMI male-male cable Power LED Indicator: Power LED indicator Signal LED Indicator: Signal LED indicator Rear Panel... -
Page 6: Receiving Unit
IR Blaster: Infrared 3.5mm socket for plugging in the extension cable of IR blaster Receiving unit ► AV-GM04A3-S1-IR-RX Front Panel HDMI OUT: Connect to a HDMI display with a HDMI male-male cable. Power LED Indicator: Power LED indicator Signal LED Indicator: Signal LED indicator... -
Page 7: Connection Diagram
CONNECTION DIAGRAM 1 to 1... - Page 8 Cascading...
-
Page 9: Ir Pass-Through
IR PASS-THROUGH IR Extenders IR Blaster IR Receiver IR Sockets IR BLASTER: plug in the IR blaster to emit all IR command signals received from the IR receiver from the other end to control the devices corresponding to the IR signals. IR RECEIVER: plug in the IR receiver to receive all IR command signals from the IR remote controls of the corresponding devices. -
Page 10: Hardware Installation
1. Connect a HDMI or DVI source (such as a Blu-ray Disc player) to the transmitting unit AV-GM04A3-S1-IR-TX. 2. Connect a HDMI or DVI display (such as a LCD TV) to the receiving unit AV-GM04A3-S1-IR-RX. 3. Connect IR Blaster/Receiver to both TX and RX units. - Page 11 Pin 1 TMDS Data2+ Pin 11 TMDS Clock Shield Pin 2 TMDS Data2 Shield Pin 12 TMDS Clock– Pin 3 TMDS Data2– Pin 13 Pin 4 TMDS Data1+ Pin 14 Reserved (N.C. on device) Pin 5 TMDS Data1 Shield Pin 15 Pin 6 TMDS Data1–...
-
Page 12: Notice
NOTICE 1. When adjusting the signal level on the receiver unit, please dial the rotary control switch from MIN to MAX and stop turning the rotary switch whenever the audio/video is playing normally. Inappropriate signal level setting may cause overpowering issue that would shorten the product life significantly! 2. -
Page 13: Warranty
The SELLER will NOT be liable for direct, indirect, incidental, special, or consequential damages resulting from any defect or omission in this manual, even if advised of the possibility of such damages. Also, the technical information contained herein regarding the AV-GM04A3-S1-IR features and specifications is subject to change without further notice.
Need help?
Do you have a question about the AV-GM04A3-S1-IR and is the answer not in the manual?
Questions and answers