Table of Contents
Advertisement
Quick Links
The SG800 is born from the elegance and prestige that has always distinguished BEINAT S.r.l. and from
the home fitness concept.
The probe is a Catalytic gas detection unit with IP66 protection that, together with one of BEINAT's industrial
type Control Units or stand-alone, detects the presence of esplosive gas such as Methane, LPG, Hydrogen,
Freon, Chlorine, Idrogen Sulphide,
The probe has two danger levels:
1
st
LEVEL, pre-alarm. This was set at see Table on page 2
nd
2
LEVEL, main alarm. This was set at see Table on page 2
For Oxygen ALARM, for <Oxygen deficiency and > Oxygen Excess
The probe is managed by a microprocessor which not only supplies an alarm signal to the control unit connected
to it, but also allows execution of a self-diagnosis and therefore an AUTOMATIC CALIBRATION, in order to always
have the maximum detection accuracy.
The self-calibration means the probe adapts in harsh and variable temperature environments, avoiding false alarms
due to anomalous events.
The probe has a 0 ÷ 20 % LEL linear output conforming to the 4 ÷ 20mA standard, for which can be connected
with one of BEINAT's industrial control units.
The important innovation of this probe is:
The possibility to substitute the sensor at the end of the operating cycle or fault by the technician without having
to send to BEINAT Srl.
Instrument of testing TS1008
To facilitate the reading of the functional parameters of the probe as well as the
control of annual operating, the BEINAT
The tester allows to read all the data in the memory of the probes eand by serial
transmission, it prints the ticket that confirms the testing data, certifying your own work.
Important: Assembly / maintenance of the appliance must be carried out by qualified personnel and in
accordance with applicable laws and regulations.
The manufacturer assumes no responsibility for the use of products that have to comply with particular
environmental and / or installation standards.
Important note
Before connecting the equipment, it is recommended that you read the instruction manual carefully and
keep it for future reference. It is also recommended to perform the electrical connections correctly as
per enclosed drawings, observing the instructions and the Standards.
N.B. Refer to the documentation in all cases where the symbol is on the side
Installation and user
guide
Stand-alone Gas Sensor SG800
OXYGEN, and other type of gas.
S.r.l.
has built a new portable tester TS1008.
Electric connections also available on
CONFORMITY
EN 50194
EN 50270
Compliant EN 60079-29-1
Installation EN 60079-29-2
Reports issued by TUV Italia
Channel: Beinat gas solutions
V. R4
Advertisement
Table of Contents
Related Manuals for BEINAT SG800
Summary of Contents for BEINAT SG800
- Page 1 Stand-alone Gas Sensor SG800 V. R4 The SG800 is born from the elegance and prestige that has always distinguished BEINAT S.r.l. and from the home fitness concept. The probe is a Catalytic gas detection unit with IP66 protection that, together with one of BEINAT’s industrial...
- Page 2 When doing the electrical connections, follow the drawing closely. Any use of the detector for purposes other than the intended one is considered improper, and as a result of which BEINAT S.r.l. therefore disclaims any responsibility for possible damages caused to people, animals or objects.
- Page 3 Compatible control units CONTROL UNITS MOUNTING PROBES Max. DEGREE ALARMS POSITIVE OPERATING protec. alarms safety range GS100M unit 1 zone Wall/cabinet I P 4 4 Y E S GS300M unit 1 zone Wall/cabinet I P 4 4 Y E S BX444-MC unit 1 zone Wall/cabinet I P 4 4...
- Page 4 Positioning of the Probe The positioning of the probe is a factor of crucial importance for the correct functioning of gas detection. In order to obtain the maximum results from an appliance and minimize the probabilities of false alarms, we recommend to follow this diagram and to keep in mind the following general rules.
- Page 5 Before connecting to the mains power, ensure the voltage is correct. Carefully follow the instructions and the connections according to Regulations in force, keeping in mind that the signal cables should be laid separate from the power cables. Description and connecting probe SG800 for explosive gases Led Pre-alarm Led alarm...
- Page 6 220 Ohm resistance installed between terminal 2 Power Supply and terminal 3. 12÷24 V. Linear Otput 4-20 mA If other problems arise, the Distributor of BEINAT S.r.l. should be contacted directly. Page 6...
- Page 7 The probe continues to blink at a low frequency again for 24 hours to make sure that the probe do the auto calibration. Gas Input Test TEST SG800 The installation of the SG800 probe, its ordinary and Ammo nia At 20% del L.I.E. ±2% extraordinary maintenance, and its out of service removal at Acetylen At 20% del L.I.E.
- Page 8 Defects caused by unauthorized personnel tampering, incorrect installation and negligence resulting from phenomena outside normal functioning shall be excluded from the warranty. BEINAT S.r.l. is not liable for possible damage, direct or indirect, to people, animals, or things; from product faults and from its enforced suspension of use.
Need help?
Do you have a question about the SG800 and is the answer not in the manual?
Questions and answers