Related Manuals for Omron MicroHAWK V/F3 F Series
Summary of Contents for Omron MicroHAWK V/F3 F Series
- Page 1 MicroHAWK Optics and Lighting Accessory Kit Installation Guide Z435-E-01 (84-9320017-02)
-
Page 2: Table Of Contents
MicroHAWK Optics and Lighting Accessory Kit Installation Guide This guide contains instructions for how to install the optical accessories on a MicroHAWK ID/MV-20, V/F320-F, V/F330-F, V/F420-F and V/F430-F. Contents 1. MicroHAWK ID/MV-20 Diffuser and Polarizer Kit Installation 2. MicroHAWK V/F3XX-F Diffuser and Polarizer Kit Installation 3. -
Page 3: Kit, Diffuser, Microhawk Id
MicroHAWK ID/MV-20 Diffuser and Polarizer Installation Diffuser Kit Hardware, MicroHAWK ID/MV-20 Description Kit Part Number Kit, Diffuser, MicroHAWK ID/MV-20 98-9000077-01 Diffuser Kit Installation, MicroHAWK ID-20/MV-20 Step 1: Peel the protective liner from the adhesive on the diffuser. Step 2: Rest the narrow edge of the diffuser on the bottom edge of the window opening at an angle as shown below. -
Page 4: Kit, Polarizer, Microhawk Id
Polarizer Kit Hardware, MicroHAWK ID-20/MV-20 Description Kit Part Number Kit, Polarizer, MicroHAWK ID/MV-20 98-9000062-01 Polarizer Kit Installation, MicroHAWK ID-20/MV-20 Step 1: Peel the protective liner from adhesive on the polarizer. Step 2: Rest the narrow edge of the polarizer on the bottom edge of the window opening at an angle as shown below. -
Page 5: Kit Part Number
MicroHAWK V/F320 and V/F330 Diffuser and Polarizer Installation Diffuser Kit Hardware, MicroHAWK V/F330 and V/F320 Description Kit Part Number Kit, Diffuser, MicroHAWK V/F330 V330-AF1 Diffuser Kit Installation, MicroHAWK V/F330 and V/F320 Step 1: Follow same steps as above for the ID/MV-20 Note: Take care to align the Diffuser so that the narrow edge is at bottom, that there is an equal gap laterally, and that the bottom edge is aligned with bottom edge of window. -
Page 6: V430-Af0
MicroHAWK V/F4XX-F Window and LED Kit Installation Window Kit Hardware, MicroHAWK V/F430-F and V/F420-F Description Kit Part Number Window, Diffuser, Polarizer or Filter Kits V430-AF0 (Window) (included) V430-AF1 (Diffuser) V430-AF2 (Polarizer) V430-AF4 (YAG Filter) V430-AF5 (ESD Window) V430-AF6 (Red Filter) 0-80 Phillips-Head Screws (included) V430-AF7 (Blue Filter) Gasket (included) - Page 7 Outer LED Removal, MicroHAWK V/F4XX-F Note: If installing an LED accessory only, skip to Step 6. Step 4: Remove the two screws from the LED boards. Step 5: Unplug the LED boards from the camera. Note: The LED boards have a connector interface. Gently pry the top of each LED board from the main board using fine-tipped tweezers or an equivalent tool.
- Page 8 Window Installation, MicroHAWK V/F4XX-F Step 8: Install the gasket onto the camera. Ensure that the gasket is properly seated in place and is covering all sealing surfaces. Step 9: Install the window (or window accessory) onto the camera. Step 10: Secure the window in place using the screws provided. Do not over-tighten the screws. (1.0 in./lbs.
-
Page 9: V430-Af0R
MicroHAWK V/F430-F with Ring Light Window and LED Installation Window Kit Hardware, MicroHAWK V/F430-F with Ring Light Description Part Number Window Assembly (included) V430-AF0R (Window) V430-AF1R (Diffuser) Window Gasket (included) #2-56 X 3/8” Phillips Flat Head Screw (included) #4-40 X 1/4” Phillips Pan Head Screw w/ Lock Washers (included) Phillips Torque Wrench (not included) LED Kit Hardware, MicroHAWK V/F430-F with Ring Light... - Page 10 Outer LED Removal, MicroHAWK V/F430-F Ring Light Step 5: Unplug the LED board from the camera. Note: The LED board has two connectors on the left and right of the camera front face. Gently pry the LED board from the camera using fine-tipped tweezers or an equivalent tool. Use caution not to contact the LEDs as they may become damaged.
- Page 11 Window Installation, MicroHAWK V/F430-F with Ring Light Step 7: Reinstall the new #2-56 flat head screws through the diffuser into the camera PEM nuts. Do not overtighten the screws (1.9 in-lbs. (0.21 Nm) max) Step 8: Install the new gasket, ensuring that it is fully constrained within the gasket groove. Step 9: Place the window on the front of the unit and secure with the new #4-40 pan head screws and lock washers.
-
Page 12: V430-Af2R
MicroHAWK V/F430-F with Ring Light Polarizer Installation Polarizer Kit Hardware, MicroHAWK V/F430-F with Ring Light Description Kit Part Number Window Assembly (included) V430-AF2R (Polarizer) Window Gasket (included) #2-56 X 3/8” Phillips Flat Head Screw (included) #4-40 X 1/4” Phillips Pan Head Screw w/ Lock Washers (included) Phillips Torque Wrench (not included) Window Removal, MicroHAWK V/F430-F with Ring Light... - Page 13 Polarizer Window Installation, MicroHAWK V/F430-F with Ring Light Step 5: Reinstall the new #2-56 flat head screws in the LED board PEM nuts without replacing the diffuser. Do not overtighten the screws (1.9 in-lbs. (0.21 Nm) max) Step 6: Install the new gasket, ensuring that it is fully constrained within the gasket groove. Step 7: Place the polarizer window on the front of the unit and secure with the new #4-40 pan head screws and lock washers.
- Page 14 The Netherlands Hoffman Estates, IL 60169 U.S.A. Tel: (31)2356-81-300/Fax: (31)2356-81-388 Tel: (1) 847-843-7900/Fax: (1) 847-843-7787 © OMRON Corporation 2019 All Rights Reserved. OMRON (CHINA) CO., LTD. OMRON ASIA PACIFIC PTE. LTD. In the interest of product improvement, Room 2211, Bank of China Tower, No.