Table of Contents
Advertisement
Read the following important safety information before using this equipment to avoid
serious injury or death and to avoid damage to equipment or property.
WARNING
ELECTRIC SHOCK HAZARD:
• For
hard-wired
connections must be in accordance with
local electrical codes and any other
applicable codes. Connections should be
made by a qualified, licensed electrician.
• Units equipped with a cord and plug supplied
by Hatco must be plugged into a properly
grounded electrical outlet of the correct
voltage, size, and plug configuration. If the
plug and receptacle do not match, contact a
qualified electrician to determine and install
the proper voltage and size electrical outlet.
• Unplug the power cord or turn the power OFF
at the fused disconnect switch/circuit
breaker and allow the unit to cool before
performing any maintenance or cleaning.
• Discontinue use if power cord is frayed or
worn.
• Do not attempt to repair or replace a
damaged power cord. The cord must be
replaced by Hatco, an Authorized Hatco
Service Agent, or a person with similar
qualifications.
• DO NOT submerge or saturate with water.
Unit is not waterproof. Do not operate if unit
has been submerged or saturated with water.
• This unit is not "jet-proof" construction. Do
not use jet-clean spray to clean this unit.
• Use only Genuine Hatco Replacement Parts
when service is required. Failure to use
Genuine Hatco Replacement Parts will void
all warranties and may subject operators of
the equipment to hazardous electrical
voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are
specified
to
operate
environments in which they are used. Some
aftermarket or generic replacement parts do
not have the characteristics that will allow
them to operate safely in Hatco equipment.
Form No. GRM-0508
All manuals and user guides at all-guides.com
IMPORTANT SAFETY INFORMATION
units,
all
electrical
safely
in
the
FIRE HAZARD:
• Locate the unit the correct distance from
combustible walls and materials. If safe
distances are not maintained, discoloration
or combustion could occur. Refer to specific
installation and mounting information in this
manual for proper clearances.
• Make
sure
to
information listed below for specific strip
heaters. If safe distances are not maintained,
discoloration or combustion could occur.
a. Do not install standard wattage strip
heaters (GR, GRA, GRN, GRAL Series)
less than 10" (254 mm) above combustible
surfaces.
b. Do not install high wattage strip heaters
(GRH, GRAH, GRNH, GRAHL Series) less
than 13-1/2" (343 mm) above combustible
surfaces.
c. Do not install dual strip heaters (GRA-
XXD, GRAH-XXD, GRAL-XXD, and GRAHL-
XXD Series) above combustible surfaces.
e. Install all single strip heaters with a
minimum distance of 3" (76 mm) from a
combustible wall or adjacent surface.
• Do not store or use gasoline or other
flammable vapors or liquids in the vicinity of
this or any other appliance.
Use only light bulbs that meet or exceed
(National
Sanitation
standards and are specifically designed for food
holding areas. Breakage of light bulbs not
specially coated could result in personal injury
and/or food contamination.
For installation with chains, make sure the
chains have sufficient strength and are securely
fastened to both the unit and the mounting
location. Poorly installed chains may cause the
unit to loosen and fall. Do not place anything on
top of units installed with chains.
This unit has no "user-serviceable" parts. If
service is required on this unit, contact an
Authorized Hatco Service Agent or contact the
Hatco Service Department at 800-558-0607 or
414-671-6350; fax 800-690-2966; or International
fax 414-671-3976.
1
WARNING
follow
the
installation
Foundation
(NSF)
Hide quick links:
Advertisement
Table of Contents
