Subscribe to Our Youtube Channel
Related Manuals for SIIG AV-GM02X3-S1
Summary of Contents for SIIG AV-GM02X3-S1
- Page 1 HDMI extender over single cat.X with bi-directional IR, and Auto EDID Learning P/N: AV-GM02X3-S1...
-
Page 2: Table Of Contents
However, like all electronic equipments, the AV-GM02X3-S1 should be used with care. Please read and follow the safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit. -
Page 3: Introduction
50m (165ft) in HDTV 1080i format, 40m (130ft) in HDTV 1080p format, and 20m (65ft) in HDTV 1080p with 36-bit color depth. AV-GM02X3-S1 also supports the most advanced 3D video format and therefore guarantees the highest 3D video compatibility on the market. -
Page 4: Specifications
SPECIFICATIONS Model Name AV-GM02X3-S1 Technical AV-GM02X3-S1 [Tx] AV-GM02X3-S1 [Rx] Role of usage Transmitter [TX] Receiver [RX] HDMI compliance HDMI Deep Color & full 3D HDCP compliance Video bandwidth Single-link 225MHz [6.75Gbps] Video support 480i / 480p / 720p / 1080i / 1080p60 HDMI over UTP Full HD (1080p)-40m (130ft) [CAT.X]... -
Page 5: Panel Descriptions
PANEL DESCRIPTIONS Transmitting unit ► AV-GM02X3-S1-TX Front Panel 1. +5V DC: Connect to 5V DC power supply 2. HDMI IN: Connects to a HDMI source with a HDMI male-male cable 3. EDID Learning Mode: 0 – EDID Full-HD (1080p@60)(1080p@30)(1080p@24)(1080i@60)(720p@60) – 24bit 2D video &... -
Page 6: Receiving Unit ► Rx
Receiving unit ► AV-GM02W3-S1 Front Panel 7. +5V DC: Connect to 5V DC power supply 8. HDMI OUT: Connects to a HDMI display with a HDMI male-male cable 9. Signal Level: Adjust the 8-level equalization control to the received HDMI signals. The HDMI signal level varies from MAX (strongest) to MIN (weakest) for respective transmission length from longest possible range to short distance. -
Page 7: Package Contents
PACKAGE CONTENTS 1x AV-GM02X3-S1 [TX & RX] 1x IR blaster 1x IR receiver 2x DC 5V 2A power supply 1x User Manual 1x Rack-mounting ear sets CONNECTION DIAGRAM... -
Page 8: Ir Pass-Through
IR PASS-THROUGH IR Extenders IR Blaster IR Receiver IR Sockets IR BLASTER: plug in the IR blaster to emit all IR command signals received from the IR receiver from the other end to control the devices corresponding to the IR signals. IR RECEIVER: plug in the IR receiver to receive all IR command signals from the IR remote controls of the corresponding devices. -
Page 9: Hardware Installation
6. Plug in 5V DC power supply unit to the power jack of the receiving unit AV-GM02W3-S1. 7. Plug in 5V DC power supply unit to the power jack of the transmitting unit AV-GM02X3-S1-TX. 8. If you see flickering or blinking image on the display, please adjust the rotary control switch to improve the cable skew. -
Page 10: Notice
NOTICE 1. When adjusting the signal level on the receiver unit, please dial the rotary control switch from MIN to MAX and stop turning the rotary switch whenever the audio/video is playing normally. Inappropriate signal level setting may cause overpowering issue that would shorten the product life significantly! 2. -
Page 11: Warranty
The SELLER will NOT be liable for direct, indirect, incidental, special, or consequential damages resulting from any defect or omission in this manual, even if advised of the possibility of such damages. Also, the technical information contained herein regarding the AV-GM02X3-S1 features and specifications is subject to change without further notice.
Need help?
Do you have a question about the AV-GM02X3-S1 and is the answer not in the manual?
Questions and answers