Enter Starter Program Mode - See Page 7 for details on entering program mode
Setting 1- Special Door Lock/ Unlock Operations
1 Type `1
2 Type 2
3* Normal Operation
Press the Program Button 1 time to select setting 1 (This will be confirmed by 1 LED flash)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
Setting 2- Gas/ Diesel Mode- Blue Wire on 14-Pin
1 Negative Glow Plug
2 Timed Delay
3* Gas/ Glow Plug (+)
Press the Program Button 2 times to select setting 2 (This will be confirmed by 2 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
Setting 3- Rearm Output- Yellow Wire on 14-Pin
1 Type 1
2 Type 2
3* Factory Re-arm
Press the Program Button 3 times to select setting 3 (This will be confirmed by 3 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
Setting 4- Run Time
1 30 Min Run Time
2 45 Min Run Time
3* 15 Min Run Time
Press the Program Button 4 times to select setting 4 (This will be confirmed by 4 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
Setting 5-Maximum Crank Time
1 10 Seconds
1 Flash
2 3 Seconds
2 Flashes
3* 5 seconds
3 Flashes
Press the Program Button 5 times to select setting 5 (This will be confirmed by 5 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
Setting 6- Starter Kill / Aux. Horn - Orange wire on 14-Pin Con.
1 Horn Output
2* Starter Disable
Press the Program Button 6 times to select setting 6 (This will be confirmed by 6 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
Setting 7- Sensor Disconnect - Blue wire on 3-Pin Con.
1 Positive Start Input
2 Positive Disconnect
3* Positive Disconnect 3 Flashes
Press the Program Button 7 times to select setting 7 (This will be confirmed by 7 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
10
1 Flash
Unlock pulse before start, lock pulse after start and after shutdown
2 Flashes
Lock pulse after remote starter shuts off
3 Flashes
No additional re-lock pulses
1 Flash
Waits a Maximum of 30 second before starting.
2 Flashes
Ignition ON for 10 seconds before engaging remote starter
3 Flashes
If no diesel input is detected the vehicle will start after two seconds.
1 Flash
Pulse after start and with lock
2 Flashes
Pulse after start only
3 Flashes
0.75 second pulse with lock and after shutdown
1 Flash
Remote Starter runs for 30min when activated
2 Flashes
Remote Starter runs for 45min when activated
3 Flashes
Remote Starter runs for 15 min when activated
10 sec Max time that starter will stay engaged
3 sec Max time that starter will stay engaged
5 sec Max time that starter will stay engaged
1 Flash
Pulsed output to activate negative horn.
2 Flashes
Negative output while the system is armed
1 Flash
Positive pulse will activate remote starter.
2 Flashes
Alarm will trigger if disconnected from 12 volts.
Alarm will trigger if disconnected from 12 volts.
Installation Guide
Continued on next page...