1. Manuals
  2. Brands
  3. Ultra Start Manuals
  4. Remote Starter
  5. 80 Series
  6. Installation manual

Ultra Start 80 Series Installation Manual

Ultra start 80 series remote starters for automatic and manual transmission models
Hide thumbs Also See for 80 Series:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Owner's Manual
REV.2011.7.22
AUTOMATIC AND MANUAL TRANSMISSION MODELS*
WARNING: NEVER USE AN AUTOMATIC TRANSMISSION
This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions:
2.This device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the part responsible for compliance void the user's authority to operate
INSTALLATION GUIDE
*MUST USE M SERIES REMOTE STARTER!
STARTER IN A MANUAL TRANSMISSION VEHICLE!
www.ultrastarters.com
FCC ID NOTICE
1. This device may not cause harmful interference, and
80 SERIES
Advanced Remote Starters & Vehicle Security Systems
this devise.
TM
TM

Advertisement

Table of Contents
loading

Related Manuals for Ultra Start 80 Series

Summary of Contents for Ultra Start 80 Series

  • Page 1 REV.2011.7.22 80 SERIES Advanced Remote Starters & Vehicle Security Systems INSTALLATION GUIDE AUTOMATIC AND MANUAL TRANSMISSION MODELS* *MUST USE M SERIES REMOTE STARTER! WARNING: NEVER USE AN AUTOMATIC TRANSMISSION STARTER IN A MANUAL TRANSMISSION VEHICLE! www.ultrastarters.com FCC ID NOTICE This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: 1.
  • Page 2 80 SERIES PAGE 2 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 TABLE OF CONTENTS QUICK VIEW WIRING DIAGRAM............3-4 Connector Pin Configuration Antenna Connector Park Light Jumper INSTALLATION NOTES................5 TACH LEARNING..................6 Tach/ Tachless Learn Hybrid Mode QUICK VIEW PROGRAMMING..............7-9 Enter Program Mode System Reset Menu 1,2,3 &...
  • Page 3 80 SERIES PAGE 3 QUICK VIEW WIRE DIAGRAM INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 OUTPUT TO ACTIVATE THE STARTER CIRCUIT YELLOW OUTPUT TO ACTIVATE ACCESSORY CIRCUIT GREEN 12VOLT/ 30 AMP MAIN POWER INPUT 12VOLT/ 30 AMP MAIN POWER INPUT...
  • Page 4 80 SERIES PAGE 4 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 QUICK VIEW WIRE DIAGRAM OUTPUT TO ACTIVATE DOOR LOCK CIRCUIT (-) GREEN OUTPUT FOR VOLTAGE INVERTER* N/A* OUTPUT TO ACTIVATE DOOR UNLOCK CIRCUIT (-) BLUE PRE-WARN TRIGGER FOR ALARM MODELS (-)
  • Page 5 80 SERIES PAGE 5 NOTES INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 PLEASE NOTE * THE CENTRE PIN OF THE KEYLESS CONNECTOR IS LOW CURRENT AND IS DESIGNED TO SUPPLY POWER TO DOOR LOCK MODULES (DO NOT CONNECT TO RELAYS) OVERLOADING THIS OUTPUT WILL DAMAGE THE MODULE! **THIS CONNECTOR IS USED FOR ALARM MODELS ONLY.
  • Page 6 80 SERIES PAGE 6 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 SYSTEM WIRING DETAILS AUTO TACH/ TACHLESS LEARNING 2 CHIRPS/ 2 FLASHES = TACH MODE Start the vehicle with 3 CHIRPS/ 3 FLASHES = DATA TACH MODE the ignition key.
  • Page 7 80 SERIES PAGE 7 PROGRAM MODE INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 ENTERING PROGRAM MODE 1 - Cycle the Ignition Key On/Off On/Off On (Leaving the key ON) 2 - Press and release the Program Switch 1 time. The park lights will turn on and the Horn (optional/ Siren (alarm model) will chip to confirm program mode entered.
  • Page 8 80 SERIES PAGE 8 INSTALL MANUAL PROGRAM MODE SYSTEM PROGRAMMING - Menu 1 PROGRAM MODE 1 (1 Flash/ 1 Chirp) SETTING # SETTING OPTION 1 OPTION 2 OPTION 3 LED FLASHES DESCRIPTION 1 CHIRP 2 CHIRPS 3 CHIRPS IGNITION IGNITION AUTO-LOCK /...
  • Page 9 80 SERIES PAGE 9 PROGRAM MODE INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 SYSTEM PROGRAMMING - Menu 1 PROGRAM MODE 3 (3 Flashes/ 3 Chirps) SETTING # SETTING OPTION 1 OPTION 2 OPTION 3 DESCRIPTION 1 CHIRP 2 CHIRPS 3 CHIRPS...
  • Page 10 80 SERIES PAGE 10 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 SYSTEM WIRING DETAILS 6-PIN CONNECTOR OUTPUT TO ACTIVATE START CIRCUIT YELLOW OUTPUT TO ACTIVATE ACCESSORY/ HEATER CIRCUIT GREEN 30A HIGH CURRENT 12VOLT INPUT 30A HIGH CURRENT 12VOLT INPUT SELECTABLE OUTPUT (DEFAULT SECOND IGNITION)
  • Page 11 80 SERIES PAGE 11 SYSTEM WIRING DETAILS INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 PIN-1 YELLOW Starter Output-This wire will test 0V when the key is off, in the Accessory position and when the Ignition is in the on position. The starter wire is 12volts during the start/ crank position only.
  • Page 12 80 SERIES PAGE 12 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 SYSTEM WIRING DETAILS 13 PIN CONNECTOR OUTPUT FOR FACTORY ALARM RE-ARM YELLOW OUTPUT FOR FACTORY ALARM DIS-ARM BROWN NEGATIVE STARTER OUTPUT GRAY OUTPUT FOR TRUNK RELEASE ACTIVATION RED/WHT NEGATIVE ACCESSORY OUTPUT/ AUXILIARY OUTPUT 2...
  • Page 13 80 SERIES PAGE 13 SYSTEM WIRING DETAILS INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 1-YELLOW Re-arm(-) (Programmable) - Supplies one .75 second pulse when locked and one .75 second pulse after remote start shutdown. Factory alarm re-arm/ RAP shutdown. 2-BROWN Dis-arm(-) - .75 second pulse when unlock button is pressed and one...
  • Page 14 80 SERIES PAGE 14 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 SYSTEM WIRING DETAILS 4 PIN AUXILIARY SENSOR CONNECTOR* PRE-WARN TRIGGER BLUE FULL TRIGGER INPUT GREEN *ALARM MODELS ONLY GROUND OUTPUT FOR AUXILIARY SENSOR BLACK 12VOLT OUTPUT FOR AUXILIARY SENSOR...
  • Page 15 80 SERIES PAGE 15 SHOCK SENSOR PROGRAM INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 ALARM MODELS ONLY 1 - ENTER SHOCK SENSOR ADJUSTMENT MODE Press & HOLD Lock + Unlock buttons at the same time Continue to hold the buttons for 3-5 seconds until the SIREN...
  • Page 16 80 SERIES PAGE 16 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 TRANSMITTER PROGRAMMING SYSTEM PROGRAMMING - Menu 1 The system can lean up to 4 different remote’s. Each remote to be used MUST be programmed together during the same sequence. For security, when a new remote is programmed all previous remote’s are deleted.
  • Page 17 80 SERIES PAGE 17 DIAGNOSTICS INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 DIAGNOSTICS CHART If the remote starter does not activate when the start button is pressed the park lights will flash a diagnostic to indicate what shutdown input has been triggered. For example: If the start button is pressed the park lights flash 3 times slowly.
  • Page 18 80 SERIES PAGE 18 INSTALL MANUAL RELAY DIAGRAMS DOOR LOCK DIAGRAMS Vehicle's Lock/Unlock Switch Door lock Output To Control Relay or Actuators Green Blue Ground Vehicle's Lock/ Unlock Switch Door lock Output 12volts Green Blue Ground 12volts USE SPDT 12v Relay...
  • Page 19 80 SERIES PAGE 19 RELAY DIAGRAMS INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 DOOR LOCK DIAGRAMS Ground Vehicle's Lock/ Unlock Switch Door lock Output 12volts Green Blue Ground Lock Resistor 12volts Unlock Resistor USE SPDT 12v Relay 12volts Lock/ Unlock Switch...
  • Page 20 80 SERIES PAGE 20 INSTALL MANUAL **FOR DETAILED VEHICLE WIRING INFORMATION GO TO: http://www.ultrastarters.com/wiring_diagrams.html This site is for registered and authorized dealer only. If you are an authorized dealer but have been registered, please fill out the service request form at http://www.ultrastarters.com/wiring_diagrams.html...

Table of Contents