Table of Contents
Advertisement
Quick Links
All manuals and user guides at all-guides.com
FCC/ID Notice
This device complies with Part 15 of the FCC rules. Operation is
subject to the following conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the
part responsible for compliance void the user's authority to operate
this devise.
Advertisement
Table of Contents
Related Manuals for Ultra Start 2250
Summary of Contents for Ultra Start 2250
- Page 1 All manuals and user guides at all-guides.com FCC/ID Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
-
Page 2: Table Of Contents
All manuals and user guides at all-guides.com NSTALLATION UIDE TABLE OF CONTENTS 2250 Wiring Diagram Page 3 Pre-Installation Page 4 Components Recommended Pre-Installation Procedures Recommended Install Procedures Wire Connectors Page 5 6 Pin Connector 14 Pin Connector 3 Pin Red Connector... - Page 3 All manuals and user guides at all-guides.com NSTALLATION UIDE WIRING DIAGRAM YELLOW RED/WHITE BROWN ORANGE WHITE/BLUE BLACK/WHITE PURPLE WHITE GREEN/WHITE GREEN BLACK PINK BLUE/WHITE BLUE *This input is a optional connection for “TL” models. This input is programmable and may need to be programmed for Tachless operation. See Page 11. Note: The center pin of this connector is low current and designed to power a Voltage Inverter.
-
Page 4: Recommended Pre-Installation Procedures
INSTALLATION GUIDE All manuals and user guides at all-guides.com INSTALLATION TIPS Components - Control module - Remote transmitter(s) - Antenna with built in program button and LED’s - 6 pin main harness with dual 30amp power inputs - 14 pin harness - 3 pin - 2 wire keyless entry harness - Multi-tone siren - Hood pin safety switch... -
Page 5: 14 Pin Connector
INSTALLATION GUIDE All manuals and user guides at all-guides.com WIRING CONNECTIONS 6 Pin Power Connector Yellow Starter 30amp output 12volts during crank only. Green Heater 30amp output 12volts in accessory. Off during start. 12 power 30amp input Constant 12volt power at ignition harness. 12 power 30amp input Constant 12volt power at ignition harness. - Page 6 INSTALLATION GUIDE All manuals and user guides at all-guides.com QUICK START INSTALL QUICK START INSTALL Step 1 - Connect All Of the Following Wires 6 Pin Power Connector Yellow Starter Output Connect The Yellow Wire From The 6 Pin T o The Vehicles Starter Wire. Green Heater Output Connect The Green Wire From The 6 Pin To The Vehicles Accessory Wire.
-
Page 7: Installation
INSTALLATION GUIDE All manuals and user guides at all-guides.com PROGRAMMING PROGRAMMING Programming Overview Program mode allows you to adjust the settings and options of your system. Your system has been intelligently designed by installers with years of experience. The system’s default settings do not require any program changes in most cases. - Page 8 All manuals and user guides at all-guides.com INSTALLATION GUIDE PROGRAMMING PROGRAMMING PROGRAM MODE - USER SETTINGS Setting 1- Ignition Auto Lock 1 Ignition Lock & Unlock Enabled 1 Light Flash Doors Lock / Unlock when the key is turned On/ Off 2 Ignition Lock Only 2 Light Flashes Doors Lock when ignition key is turned ON only...
- Page 9 All manuals and user guides at all-guides.com INSTALLATION GUIDE PROGRAMMING PROGRAMMING PROGRAM MODE - ALARM SETTINGS Enter Alarm Program Mode - See Page 7 for details on entering program mode Setting 1 - Secure Valet Mode 1 Secure Valet Active 1 Flash Valet only if ignition “ON”...
- Page 10 All manuals and user guides at all-guides.com INSTALLATION GUIDE PROGRAMMING PROGRAM MODE - STARTER SETTINGS Setting 1- Special Door Lock/ Unlock Operations 1 Type 1 1 Flash Unlock before start and a lock pulse after start & shutdown 2 Type 2 2 Flashes Lock pulse after remote starter shuts off 3* Normal Operation...
- Page 11 INSTALLATION GUIDE All manuals and user guides at all-guides.com PROGRAMMING PROGRAM MODE - TACH SETTINGS Setting 1- Tach Selection (TL Models Only) 1* Tach Detection Mode 1 Honk/Chirp Must connect Tach Wire. (Blue/White on 14-pin connector) 2 Tachless Mode 2 Honks/Chirps No Tach connection required.
-
Page 12: Reservation Mode
All manuals and user guides at all-guides.com INSTALLATION GUIDE OPERATIONS Reservation Mode - Manual Trans. Manual Transmission Remote Starters must have both the door trigger and park brake wires connected. Most installs will require a clutch bypass. This is a temporary bypass. The clutch should only be bypassed during the activation of the remote starter. -
Page 13: Service Mode
INSTALLATION GUIDE All manuals and user guides at all-guides.com OPERATIONS System Service Mode ACTIVATING SERVICE MODE 1. While the ignition is “ON” press and hold the Program Button for five seconds. The park lights will flash and the siren will chirp five times to confirm that the system is in Service Mode. 2. -
Page 14: Diagnostics
All manuals and user guides at all-guides.com INSTALLATION GUIDE OPERATIONS Lock Doors & Arm The Alarm 1.Press and release the LOCK button on the remote transmitter. 2.The park lights will flash and the siren will chirp once. 3.The doors will lock. (With Optional Keyless Entry) 4.The LED’s on the antenna will start flashing within five seconds. - Page 15 INSTALLATION GUIDE All manuals and user guides at all-guides.com OPERATIONS Reservation Mode (Manual Transmissions Only) 1. With the vehicle running, apply the park brake then press and release the brake pedal. 2. The park lights will flash and the siren will chirp to confirm that reservation mode has been activated. 3.
- Page 16 All manuals and user guides at all-guides.com Starter Kill with Bypass Units (Transponder or Passlock) 1 - Cut the Starter Wire between the key and the start Bypass Unit and connect to Pins 87a & 30 of the relay. Ignition 2 - Connect the “Constant”...