Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Ultra Start 3295Series
Summary of Contents for Ultra Start 3295Series
- Page 1 REV.2009.09.19 95 SERIES Advanced Remote Starters & Vehicle Security Systems INSTALLATION GUIDE THIS MANUAL COVERS THE OPERATIONS OF THE 3295, 4295 SERIES REMOTE STARTERS AND ALARMS WARNING: NEVER USE AN AUTOMATIC TRANSMISSION STARTER IN A MANUAL TRANSMISSION VEHICLE! www.ultrastarters.com...
-
Page 2: Table Of Contents
95 SERIES PAGE 2 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 TABLE OF CONTENTS QUICK VIEW WIRING DIAGRAM............3-4 Connector Pin Configuration Antenna Connector Park Light Jumper NOTES......................5 Addition Installation Notes QUICK VIEW PROGRAMMING..............6-9 Enter Program Mode System Reset Transmitter Programming Menu 1,2,3 &... -
Page 3: System Programming - Menu
95 SERIES PAGE 3 QUICK VIEW WIRE DIAGRAM INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 OUTPUT TO ACTIVATE THE VEHICLES STARTER CIRCUIT YELLOW OUTPUT TO ACTIVATE THE VEHICLES ACCESSORY CIRCUIT GREEN 12VOLT/ 30 AMP MAIN POWER INPUT 12VOLT/ 30 AMP MAIN POWER INPUT SELECTABLE OUTPUT* (DEFAULT 2ND IGN) WHITE* OUTPUT TO ACTIVATE... - Page 4 95 SERIES PAGE 4 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 QUICK VIEW WIRE DIAGRAM OUTPUT TO ACTIVATE DOOR LOCK CIRCUIT (-) GREEN OUTPUT FOR VOLTAGE INVERTER* N/A* OUTPUT TO ACTIVATE DOOR UNLOCK CIRCUIT (-) BLUE PRE-WARN TRIGGER FOR ALARM MODELS (-) BLUE** FULL TRIGGER FOR ALARM MODELS (-) GREEN**...
-
Page 5: Notes
95 SERIES PAGE 5 NOTES INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 PLEASE NOTE * THE CENTRE PIN OF THE KEYLESS CONNECTOR IS LOW CURRENT AND IS DESIGNED TO SUPPLY POWER TO DOOR LOCK MODULES (DO NOT CONNECT TO RELAYS) OVERLOADING THIS OUTPUT WILL DAMAGE THE MODULE! **THIS CONNECTOR IS USED FOR ALARM MODELS ONLY. -
Page 6: Quick View Programming
95 SERIES PAGE 6 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 QUICK VIEW PROGRAMMING ENTERING PROGRAM MODE 1 - Cycle the Ignition Key On/Off On/Off On (Leaving the key ON) 2 - Press and release the Program Switch 1 time. (Horn/ Siren will chip to confirm program mode entered) 3 - Select the Program Menu by pressing... - Page 7 95 SERIES PAGE 7 QUICK VIEW PROGRAMMING INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 SYSTEM PROGRAMMING - Menu 1 PROGRAM MODE 1 - see page 16 for detailed instructions SETTING # SETTING OPTION 1 OPTION 2 OPTION 3 LED FLASHES DESCRIPTION 1 CHIRP 2 CHIRPS...
- Page 8 95 SERIES PAGE 8 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 QUICK VIEW PROGRAMMING SYSTEM PROGRAMMING - Menu 1 PROGRAM MODE 3 - see page 21 for detailed instructions SETTING # SETTING OPTION 1 OPTION 2 OPTION 3 DESCRIPTION 1 CHIRP 2 CHIRPS 3 CHIRPS FLASHES...
-
Page 9: Auto Tach Learning
95 SERIES PAGE 9 TACH / TACHLESS LEARNING INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 AUTO TACH/ TACHLESS LEARNING 2 CHIRPS Horn/ Siren will chip to confirm that Start the vehicle with the Tach/ Tachless has been programmed. 4 CHIRPS the ignition key. -
Page 10: System Wiring Details
95 SERIES PAGE 10 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 INSTALL MANUAL SYSTEM WIRING DETAILS SYSTEM PROGRAMMING - Menu 1 6-PIN CONNECTOR OUTPUT TO ACTIVATE START CIRCUIT YELLOW OUTPUT TO ACTIVATE ACCESSORY/ HEATER CIRCUIT GREEN 30A HIGH CURRENT 12VOLT INPUT 30A HIGH CURRENT 12VOLT INPUT SELECTABLE OUTPUT (DEFAULT SECOND IGNITION) WHITE*... - Page 11 95 SERIES PAGE 11 INSTALL MANUAL SYSTEM WIRING DETAILS PIN-1 YELLOW Starter Output-This wire will test 0V when the key is off, in the Accessory position and when the Ignition is in the on position. The starter wire is 12volts during the start/ crank position only. PIN-2 GREEN Heater/Acc Output-This wire will test 0V when key is off, 12volts in the ACC and iIGN positions and off during start/ crank position.
- Page 12 95 SERIES PAGE 12 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 SYSTEM WIRING DETAILS 13 PIN CONNECTOR OUTPUT FOR FACTORY ALARM RE-ARM YELLOW OUTPUT FOR FACTORY ALARM DIS-ARM BROWN NEGATIVE STARTER OUTPUT GRAY OUTPUT FOR TRUNK RELEASE ACTIVATION RD/WHT NEGATIVE ACCESSORY OUTPUT/ AUXILIARY OUTPUT 2 ORG/WHT AUXILIARY OUTPUT 1/ PROGRAMMABLE OUTPUT WHT/VIO...
- Page 13 95 SERIES PAGE 13 SYSTEM WIRING DETAILS INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 1-YELLOW Re-arm(-) (Programmable) Supplies one .75 second pulse when locked and one .75 second pulse after remote start shutdown. Factory alarm re-arm/ RAP shutdown. 2-BROWN Dis-arm(-) Supplies one .75 second pulse when the unlock button is pressed and one .75 second pulse before remote start activation.
- Page 14 95 SERIES PAGE 14 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 SYSTEM WIRING DETAILS 4 PIN AUXILIARY SENSOR CONNECTOR* PRE-WARN TRIGGER BLUE FULL TRIGGER INPUT GREEN *ALARM MODELS ONLY GROUND OUTPUT FOR AUXILIARY SENSOR BLACK 12VOLT OUTPUT FOR AUXILIARY SENSOR 1- BLUE Pre-Warn Trigger (-) Input When this wire is grounded by an auxiliary sensor (i.e: Radar Sensor) the system will chirp the SIREN 3 times.
-
Page 15: Program Menus
95 SERIES PAGE 15 PROGRAM MODE INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 ENTERING PROGRAM MODE 1 - Cycle the Ignition Key On/Off On/Off On (Leaving the key ON) 2 - Press and release the Program Switch 1 time. (The park lights will turn on and the HORN will chip to confirm that program mode was entered) 3 - Select the Program Menu by pressing... -
Page 16: Program Mode
95 SERIES PAGE 16 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 PROGRAM MODE ENTERING PROGRAM MODE 1 PROGRAM SWITCH SIREN CHIRP REMOTE BUTTON IGNITION KEY Press LOCK 1 CHIRP Button to ON/OFF - ON/OFF - ON Confirming Select Menu 1 Press and release 1 time (Leaving the key ON) Program Mode... - Page 17 95 SERIES PAGE 17 PROGRAM MODE INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 CON'T FROM PREVIOUS PAGE SETTING 4- DOOR LOCK TIMING PRESS 4 CHIRP 1 TIME THE SIREN WILL CHIRP 4 TIMES WHEN SETTING 4 IS SELECTED CHANGE SETTING 4 - PRESS &...
- Page 18 95 SERIES PAGE 18 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 PROGRAM MODE CON'T FROM PREVIOUS PAGE SETTING 7- PASSIVE LOCKS PRESS 7 CHIRP 1 TIME THE SIREN WILL CHIRP 8 TIMES WHEN SETTING 8 IS SELECTED CHANGE SETTING 7 - PRESS &...
- Page 19 95 SERIES PAGE 19 PROGRAM MODE INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 ENTERING PROGRAM MODE 2 SYSTEM PROGRAMMING - Menu 1 PROGRAM SWITCH SIREN CHIRP REMOTE BUTTON IGNITION KEY Press UNLOCK 1 CHIRP Button to ON/OFF - ON/OFF - ON Confirming Select Menu 2 Press and release 1 time...
- Page 20 95 SERIES PAGE 20 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 PROGRAM MODE SETTING 4- SIREN OPTIONS PRESS 4 CHIRP 1 TIME THE SIREN WILL CHIRP 4 TIMES WHEN SETTING 4 IS SELECTED CHANGE SETTING 4 - PRESS & HOLD THE VALET SWITCH UNTIL THE SIREN CHIRP(S) GOTO SETTING 5 - PRESS &...
- Page 21 95 SERIES PAGE 21 PROGRAM MODE INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 ENTERING PROGRAM MODE 3 SETTING 3-GAS/ DIESEL MODE PRESS 3 CHIRP 1 TIME THE SIREN WILL CHIRP 3 TIMES WHEN SETTING 3 IS SELECTED CHANGE SETTING 3 - PRESS &...
- Page 22 95 SERIES PAGE 22 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 PROGRAM MODE SETTING 6- REMOTE STARTING PRESS 6 CHIRP 1 TIME THE SIREN WILL CHIRP 6 TIMES WHEN SETTING 6 IS SELECTED CHANGE SETTING 6 - PRESS & HOLD THE VALET SWITCH UNTIL THE SIREN CHIRP(S) GOTO SETTING 7 - PRESS &...
- Page 23 95 SERIES PAGE 23 PROGRAM MODE INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 PROGRAM MODE 4 SYSTEM PROGRAMMING - Menu 1 SETTING 2-ADJUST FOR UNDER-CRANK PRESS 2 CHIRP 1 TIME THE SIREN WILL CHIRP 2 TIMES WHEN SETTING 2 IS SELECTED CHANGE SETTING 2 - PRESS &...
-
Page 24: Door Lock Diagrams
95 SERIES PAGE 24 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 RELAY DIAGRAMS DOOR LOCK DIAGRAMS Vehicle's Lock/Unlock Switch Door lock Output To Control Relay or Actuators Green Blue Ground Vehicle's Lock/ Unlock Switch Door lock Output 12volts Green Blue Ground 12volts USE SPDT 12v Relay... - Page 25 95 SERIES PAGE 25 RELAY DIAGRAMS INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 DOOR LOCK DIAGRAMS Ground Vehicle's Lock/ Unlock Switch Door lock Output 12volts Green Blue Ground Lock Resistor 12volts Unlock Resistor USE SPDT 12v Relay 12volts Lock/ Unlock Switch Door lock Output Green Blue...
-
Page 26: Shock Sensor (Alarm Models)
95 SERIES PAGE 26 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 SHOCK SENSOR SETTINGS ALARM MODELS ONLY THE SHOCK SENSOR SENSITIVITY IS SET USING THE REMOTE PROGRAM MODE FEATURE. ALARM MODELS ONLY. ENTER REMOTE PROGRAM MODE TO ENTER PROGRAM MODE PRESS AND HOLD THE STATUS BUTTON ON THE M-1234 REMOTE FOR 4 SECONDS. -
Page 27: Quick View Operations Chart
95 SERIES PAGE 27 QUICK VIEW OPERATIONS INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 SYSTEM PROGRAMMING - Menu 1 QUICK VIEW OPERATION CHART CHIRPS / BUTTON LENGTH OF PRESS SYSTEM OPERATION FLASHES 1 SECOND LOCK / ARM ALARM 3 SECONDS ACTIVATE PANIC 1 SECOND (PANIC OR ALARM) ALARM/ PANIC OFF... -
Page 28: Transmitter Programming
95 SERIES PAGE 28 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 TRANSMITTER PROGRAMMING TRANSMITTER PROGRAMMING THE SYSTEM CAN LEARN UP TO 4 REMOTE TRANSMITTER. EACH REMOTE MUST BE PROGRAMMED TOGETHER DURING THE SAME SEQUENCE. FOR SECURITY REASONS ALL PREVIOUSLY PROGRAMMED TRANSMITTER WILL BE DELETED FROM MEMORY. -
Page 29: Fault Codes
95 SERIES PAGE 29 FAULT CODES INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 FAULT CODE VIA PAGER IF THE STARTER FAILS TO START THE REMOTE WILL DISPLAY A FAULT CODE ON THE LCD DISPLAY. THE TEXT “FAULT” WILL BE FOLLOWED BY THE INPUT OR CONDITION THAT IS CAUSE THE ISSUE BRAKE FAULT THIS FAULT WOULD OCCUR IF... -
Page 30: Alarm Triggers
95 SERIES PAGE 30 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 ALARM TRIGGERS ALARM TRIGGERS & PAGER MODE WHEN THE ALARM IS TRIGGERED THE SYSTEM WILL PAGE THE REMOTE WITH THE SPECIFIC ALARM TRIGGER. THE REMOTE WILL START TO BEEP AND THE LCD WILL ALTERNATE BETWEEN “ALARM”... -
Page 31: Diagnostics
95 SERIES PAGE 31 DIAGNOSTICS INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 DIAGNOSTICS CHART If the remote starter does not activate when the start button is pressed the park lights will flash a diagnostic to indicate what shutdown input has been triggered. For example: If the start button is pressed the park lights flash 3 times slowly. -
Page 32: Contact Information
95 SERIES PAGE 32 INSTALL MANUAL **FOR DETAILED VEHICLE WIRING INFORMATION GO TO: http://www.ultrastarters.com/wiring_diagrams.html This site is for registered and authorized dealer only. If you are an authorized dealer but have been registered, please fill out the service request form at http://www.ultrastarters.com/wiring_diagrams.html PRODUCT INFORMATION: www.ultrastarters.com TECHNICAL SUPPORT: support@ultrastarters.com...